The A/B loader [1] meant to be used for convenient CI testing.
The tool is installed into the same location as SA0, where it
conveniently fits due to its size, and where it makes use of
non-volatile PMIC registers to alternate between loading and
starting A or B copy of the BL2. The PMIC registers are used
because CPU registers are lost across reset.
In case the B copy is loaded, it is loaded from 8 MiB offset
from start of HF. In case the B copy fails to boot, a simple
reset of the system will switch back to booting previously
known working A copy and allow recovery.
The A/B loader sets MFIS bit MFISBTSTSR_BOOT_PARTITION to
pass the information which A/B copy is currently booting on
to TFA, which then loads the follow up components from 0 MiB
or 8 MiB offset, depending on whether the A or B copy is being
booted.
The MFISBTSTSR_BOOT_PARTITION interferes with regular A/B
switching during boot from eMMC as the boot media, where
the BootROM also sets MFISBTSTSR_BOOT_PARTITION bit in case
the system boots from SECOND eMMC HW BOOT partition.
Since the A/B loader is meant as a development and CI tool,
isolate the A/B loader use to RPC HF only and furthermore
isolate it behind new RCAR_RPC_HYPERFLASH_ABLOADER option
which is disabled by default.
[1] https://github.com/marex/abloader
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Change-Id: I04ecd50fa1405b78e1ba3949d54029034d4f22d8
In the high system load situation, bus latency increase was observed
and it made impact to other feature (e.g. audio dropouts). This is
because some modules push as much as possible traffic into the DBSC4
CAM for execution, and make increasing bus latency. Re-defining swap
priorities reduce this situation. This advice has been confirmed by
hardware developer.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Change-Id: Ifebafa883d5a997de6894198327a6025b64e4ee5
Fixed the check of the address range which the program is loaded to.
Use the addresses and sizes in the BL31 and BL32 certificates to check
that they are within the range of the target address and size
defined inside the TF-A.
It also uses the addresses and sizes in the BL33x certificates to check
that they are outside the protected area defined inside the TF-A.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Code clean up
Change-Id: Iade15431fc86587489fb0ca9106f6baaf7e926e2
Check if next NS image invades a previous loaded image.
Correct non secure image area to avoid loading a NS image to secure
Move GZ compressed payload at 32 * compressed payload size offset,
so it is loaded in non-secure area and can be decompressed into
non-secure area too. It is unlikely that the up to 2 MiB compressed
BL33 blob would decompress to payload larger than 64 MiB .
Signed-off-by: Tobias Rist <tobias.rist@joynext.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix for compressed BL33
Change-Id: I52fd556aab50687e4791e5dbc45d425f802c8757
Make sure the length of the payload is not longer than the
DRAM size in check_load_area(), and make sure the payload
end does not cross protected area start.
Signed-off-by: Tobias Rist <tobias.rist@joynext.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I4d687be577a138352be9f92e5b0b6f596ffffba9
The Draak board ID is 7, Eagle is 3, update them to match
HW documentation. Drop the U suffix from Ebisu board ID.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Idd191614a6f1f8dbbc13b8e0bc1f089090f9d20b
secure_boot_api_f is defined to take uint32_t, uint32_t, and void *
parameters. However rom_secure_boot_api_f is defined to take uint32_t *,
uint32_t *, void *. These are incompatible and cause a warning when
compiling with -Wextra. Align the rom definition to the more generic
definition from where it's called.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Change-Id: Ia030803b3c2335d220aff09fc0eef5c7615276aa
Compiling with -Wimplicit-fallthrough=3 (enabled by -Wextra) produces
many warnings about fallthrough comments either missing or being wrong.
Unify the comments so we comply with -Wextra.
Note that Coverity recommends against using the __attribute__ directive.
Also, zlib does not build with a higher value of -Wimplicit-fallthrough.
Finally, compilers strip comments before expanding macros. As such,
checkpatch's fallthrough annotation (or higher levels of the flag) isn't
really possible.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Change-Id: I060cf4f8dc04c02cbb45cf4ceb69569a8369ccee
Modify the type of the variable that stores the value for MPIDR
in the internal function from uint64_t to u_register_t.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ib5bda93d5432e0412132bddf41ead8ee3fcf9e46
Add new function so that the value of bit at WUPMSKCA57/53,
which points to CPU other than the BOOT CPU, is 1 at initialization.
Modify sequence so that value of each bit for CPU at WUPMSKCA57/53 is
basically 0 and target bit value is changed to 1 only when CPU_OFF.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Id5dafc04e1dbaf265c8b67b903c335bb1af49914
Change internal function to call when updating value for WUPMSKCA57/53.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Id20e65e27861dd73a149ff487123859581a9b5c5
Change processing of invalidate instruction cache to after changing
the RAM attribute.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> # squash with rcar_gen3: drivers: Disable data cache while Suspend To RAM
Change-Id: I61339fc5415b26074b1e0753da4c4a432e8f83d9
- Modify load destination variable of the Cert Header to static.
- Modify the return value to error (IO_FAIL) when failed to check
the Cert Header.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Ief09a841ec8d2ae236de82d04855e6a47cfb43f0
In case MFISBTSTSR bit 4 is 1, that means the loader was started as
B-side. Load the remaining boot components from 8 MiB offset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I11d882f30ca4f0cf55fd28d3470ff1063d350d10
- Added the condition where output the SSCG (MD12) setting
to log for R-Car D3.
- Added the process to switching the bit rate of SCIF by the
SSCG (MD12) setting value for R-Car D3.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Iaf07fa4df12dc233af0b57569ee4fa9329f670a9
Modified the operation register to clearing the state bit of
the SYSCISR register from SYSCISR to SYSCISCR.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I9a0820b6414425fa2f4197f60852137827414a4d
Added the process of SYSECEXTMASK bit set/clear for following
power Resume/Shutoff flow.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I71ed22840a42e7ab7d87bfd4241eec6f5ddb129b
This commit fixes a return value of console_rcar_init because it is
expected to return 1 on success but the function always returns 0.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I97a6800578e3c517c0c1e3c00dc75f0ef75e8778
This commit adds the function to change the settings used for DDR
initialization depending on the board ID and DDR rank.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I94d550cea620748f5b15499fed1b791a69d61592
This commit fixes value to write to the ICCR register according to
the hardware manual.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I1f612a482c012a6739e2f31db80224b222df766c
This commit deletes the value of the redefined CPG register.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I05cf4a449ae28adb2ddd59593971a7d0cbcb21de
Add support to identify Silicon Linux RZ/G2E evaluation kit (EK874).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id7bdbc9b0d25aa9af496d58d4bd5055579edc104
Add pin control support for RZ/G2E SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I736724cc0dd32f2169018ed7f2f48319b039b61f
DRAM initialization on RZ/G2E SoC is identical to R-Car E3 so re-use the
same.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I454fb40af4f8ce6c4c0d2a53edb307326efd02df
Add pin control support for RZ/G2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Ib5eb4f3b1b75e158ec13c4eefdbe9688344206a3
Add support for initializing DRAM on RZ/G2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id09a367b92b11a5da88f2dce6887677cc935d0c0
Add pin control support for RZ/G2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I06dc259d7d26a5a5313e8731ea72f846bfca09ed
Add support for initializing DRAM on RZ/G2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Iae23f1093f65a9efd065d37b7d6e9340ff6350b9
Switch using common ddr driver code from renesas/common/ddr directory
for RZ/G2M SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I807dcb0bc5186bd32bc1c577945d28634bb10e1f
Move ddr driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I9aef73d3e9a027a127ce7483b72d339559866727
