In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
Read bit 21 of the mode, it marks if the caller is
the bootloader or the Linux Kernel.
Power off:
Check if the comphy was already configured to PCIe, if yes,
check if the caller is bootloader, if both conditions are true
(PCIe mode and called by Linux) - skip the power-off.
In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.
NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).
Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller
to setup secure or non-secure regions of DRAM memory. The TZC controller
allows to setup upto eight such regions of memory in DRAM. This driver
provides helper functions to setup the TZC controller within DMC-620.
Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Migrate Marvell platforms from legacy console API to
multi-console API.
Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Now that MULTI_CONSOLE_API is enabled for the STM32MP1 platform,
we can remove the non MULTI_CONSOLE_API parts in the driver.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
These issues wer found by sparse:
drivers/st/clk/stm32mp1_clk.c:1524:19:
warning: incorrect type in assignment (different base types)
expected restricted fdt32_t const [usertype] *pkcs_cell
got unsigned int const [usertype] *
plat/st/stm32mp1/plat_image_load.c:13:6:
warning: symbol 'plat_flush_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
warning: symbol 'plat_get_bl_image_load_info' was not declared.
Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
warning: symbol 'plat_get_next_bl_params' was not declared.
Should it be static?
plat/st/stm32mp1/bl2_io_storage.c:40:10:
warning: symbol 'block_buffer' was not declared. Should it be static?
Signed-off-by: Yann Gautier <yann.gautier@st.com>
cppcheck:
[drivers/partition/gpt.c:19] -> [drivers/partition/gpt.c:19]:
(warning) Either the condition 'str_in!=((void*)0)' is redundant
or there is possible null pointer dereference: name.
sparse:
drivers/partition/gpt.c:39:9:
warning: Using plain integer as NULL pointer
Signed-off-by: Yann Gautier <yann.gautier@st.com>
All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.
The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.
The exceptions are files that are imported from other projects:
- CryptoCell driver
- dt-bindings folders
- zlib headers
Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
This function was needed at the time where we didn't have the
compiler_rt lib. An AArch32-specific variant was provided to handle
the 64-bit shift operation in 32-bit. This is no longer needed.
Change-Id: Ibab709a95e3a723ae2eeaddf873dba70ff2012b3
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
It isn't possible to build this driver without adding this define.
Change-Id: Iba2ced411cd8ce438787871fa01b414d32b9aa42
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
It has only been tested with a system clock of 24 MHz.
It has only been implemented for the multi console API.
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The definitions FAIL_CONTROL_*_SHIFT were incorrect, they have been
fixed.
The types tzc_region_attributes_t and tzc_action_t have been removed and
replaced by unsigned int because it is not allowed to do logical
operations on enums.
Also, fix some address definitions in arm_def.h.
Change-Id: Id37941d76883f9fe5045a5f0a4224c133c504d8b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Add support for Marvell Armada-3700 COMPHY driver
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
The "Reduced Serial Bus" is an Allwinner specific bus, bearing many
similarities with I2C. It sports a much higher bus frequency, though,
(typically 3 MHz) and requires much less handholding for the typical
task of manipulating slave registers (fire-and-forget).
On most A64 boards this bus is used to connect the PMIC to the SoC.
This driver provides basic primitives to read and write slave registers,
it will be later used by the PMIC code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The `finish_console_register` macro is used by the multi console
framework to register the `console_t` driver callbacks. It relied
on weak references to the `ldr` instruction to populate 0 to the
callback in case the driver has not defined the appropriate
function. Use of `ldr` instruction to load absolute address to a
reference makes the binary position dependant. These instructions
should be replaced with adrp/adr instruction for position independant
executable(PIE). But adrp/adr instructions don't work well with weak
references as described in GNU ld bugzilla issue 22589.
This patch defines a new version of `finish_console_register` macro
which can spcify which driver callbacks are valid and deprecates the
old one. If any of the argument is not specified, then the macro
populates 0 for that callback. Hence the functionality of the previous
deprecated macro is preserved. The USE_FINISH_CONSOLE_REG_2 define
is used to select the new variant of the macro and will be removed
once the deprecated variant is removed.
All the upstream console drivers have been migrated to use the new
macro in this patch.
NOTE: Platforms be aware that the new variant of the
`finish_console_register` should be used and the old variant is
deprecated.
Change-Id: Ia6a67aaf2aa3ba93932992d683587bbd0ad25259
Signed-off-by: Soby Mathew <soby.mathew@arm.com>
Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.
Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h
If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".
The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reference code:
==============
rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]
Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date: Thu Aug 30 21:26:41 2018 +0900
Update IPL and Secure Monitor Rev1.0.22
General Information:
===================
This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).
Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls
$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed
Other dependencies:
------------------
* mbed_tls:
git@github.com:ARMmbed/mbedtls.git [devel]
Merge: 68dbc94 f34a4c1
Author: Simon Butcher <simon.butcher@arm.com>
Date: Thu Aug 30 00:57:28 2018 +0100
* optee_os:
https://github.com/BayLibre/optee_os
Until it gets merged into OP-TEE, the port requires Renesas' Trusted
Environment with a modification to support power management.
Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Date: Thu Aug 30 16:49:49 2018 +0200
plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
* u-boot:
The port has beent tested using mainline uboot.
Author: Fabio Estevam <festevam@gmail.com>
Date: Tue Sep 4 10:23:12 2018 -0300
*linux:
The port has beent tested using mainline kernel.
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Sep 16 11:52:37 2018 -0700
Linux 4.19-rc4
Overview
---------
BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)
BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).
During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.
Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.
To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).
Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.
[1] https://github.com/renesas-rcar/arm-trusted-firmware
Tests
-----
* cpuidle
-------
enable kernel's cpuidle arm_idle driver and boot
* system suspend
--------------
$ cat suspend.sh
#!/bin/bash
i2cset -f -y 7 0x30 0x20 0x0F
read -p "Switch off SW23 and press return " foo
echo mem > /sys/power/state
* cpu hotplug:
------------
$ cat offline.sh
#!/bin/bash
nbr=$1
echo 0 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
$ cat online.sh
#!/bin/bash
nbr=$1
echo 1 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline
Signed-off-by: ldts <jramirez@baylibre.com>
Whereas the GPT table is read with io_block, the binaries to be loaded
(e.g. BL33) cannot use it, as it is not suitable to read them block by
block, or the boot time would be very bad.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This IO is required to read binaries with STM32 header.
This header is added with the stm32image tool.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
This driver is for the STMicroelectronics sdmmc2 IP
which is in STM32MP1 SoC.
It uses the MMC framework, and can address either eMMC or SD-card.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
