Allow to disable ENABLE_PIE on STM32MP2. BL31 is loaded at the beginning
of SYSRAM whatever the options set. Set ENABLE_PIE to 0 by default.
This should allow us to reduce BL31 and BL2 size.
Change-Id: Ie8c83c9205e81301eb1fdcf24b94216172586630
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
The macro STM32MP_SEC_SYSRAM_SIZE only redefine STM32MP_SYSRAM_SIZE.
Directly use the latter one and remove the STM32MP_SEC_SYSRAM_SIZE.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I9cca19fda7294be3f31ec74293ce122037541d12
BL31 will need to access a device tree for several configurations (UART,
GIC, OTP mapping...).
Create a BL31 device tree (SOC_FW_CONFIG). It is loaded in DDR, in a
spare area.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Change-Id: I320a05859e1aa3dd8db9a274e7201075a8c250c2
Add driver to support DDR on STM32MP2 platform. It drives the DDR PHY
and its firmware, as well as the DDR controller.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Change-Id: I93de2db1b9378d5654e76b3bf6f3407d80bc4ca5
Add RETRAM base address and size definition at platform level.
RETRAM is used by the DDR driver to store retention registers (DDR
training results) in order to restore them in standby exit sequence.
Add map/unmap services at platform level and configure dedicated RISAB5.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Change-Id: I460b36fccce62e83c1fbff298f96b23530aaa4f3
Change the size of BL31 limit allocation to be half the sysram size.
Defining BL31_PROGBITS_LIMIT to detect overflows.
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Change-Id: Iccc1cc0826b8113a3c2fd6ffa77ca419795854d3
This feature is enabled by default using STM32MP_DDR_FIP_IO_STORAGE.
DDR firmware binary is loaded from FIP to SRAM1 which needs to be
mapped.
Only half of the SRAM1 will be allocated to TF-A.
RISAB3 has to be configured to allow access to SRAM1.
Add image ID and update maximum number on platform side also.
Fill related descriptor information, add policy and update numbers.
DDR_TYPE variable is used to identify binary file, and image is now
added in the fiptool command line.
The DDR PHY firmware is not in TF-A repository. It can be found at
https://github.com/STMicroelectronics/stm32-ddr-phy-binary
To ease the selection of the firmware path, STM32MP_DDR_FW_PATH is added
to platform.mk file.
Change-Id: I09ab0a5c63406055a7b5ccd16d65e443de47ca2f
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Add the required files to compile BL31 on STM32MP2.
Update BL2 configuration to load BL31. The platform boots until BL31,
but stops here as no other binaries are loaded as DDR is not
initialized.
At runtime, BL31 will use only the first half of the SYSRAM, the upper
half will be used for non-secure DMA LLIs. To be sure nothing from this
area is still in the cache, invalidate the upper SYSRAM before enabling
BL31 cache. BL31 should then map only first half of the SYSRAM. But it
must temporarily map the upper half read-only, as this is where we will
retrieve BL2 parameters, used to fill registers for next boot stages.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Change-Id: Ie91527a7a26625624b4b3c65fb6a0ca9dd355dbd
The DT file will be in the FIP, and loaded at the beginning of SYSRAM.
The info for hw-config (U-Boot DT by default) is also added, it will
be loaded just after BL33 (U-Boot binary).
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I9d58428c2d911c5c16cae5164122bf833a847a7d
Print information about CPU type, package and revision.
SoC revision ID of MP2 family are defined with the OTP 102.
Signed-off-by: Maxime Méré <maxime.mere@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I14a95c8a7cb9b06ce32c2e592ae69a1741067e8d
Configure the first steps for STM32MP2 BL2 platform boot:
- Save boot context address for later use
- Configure BL2 MMU
- Load and use BL2 DT
- Reset backup domain
- Initialize clocks
- Configure UART for console
- Print some info about board and reset reason
- Setup storage (only SD-card for the moment)
The platform boot stops at BL2 image load, as bl2_mem_params_descs[]
is still empty.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: If6127cfbf77825a03afe8d65ba47c8c0661de496
This driver manages the clocks on STM32MP2 platforms.
It uses a dedicated RCC (Reset and Clock Control) peripheral.
Change-Id: I6ba2173e73222269a2dfca4c6897229276a150c0
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Add compilation and initialization of BSEC peripheral, to access OTP
fuses. Add the definition of OTP fuses.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: If6403838b1e2c04c59effc8545b381aced5f7cda
When STM32MP2 boots on Cortex-M33, the Cortex-A35 do no more have access
to BSEC peripheral. New static inline stm32_otp_* wrappers are added,
which just redirect to BSEC functions.
While at it remove a useless bsec.h include.
Change-Id: Ie0f917c02e48acf456634f455dae41805bf6adbf
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
To be able to boot, STM32MPU platforms require the BL2 binary (together
with its DT) to be preceded with an STM32 header. Add the required
files and macro to properly generate this header.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: I675de2c5cb733fe9d9e9baf76a941741a06dfac8
Use UART driver and fill helpers for crash console.
Add early console setup in bl2_el3_early_platform_setup().
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Change-Id: Ifb39554214dec05dafe4e306f8754e1454cdab61
This new STMicroelectronics SoC is based on a dual Cortex-A35.
For the moment, only BL2 is compiled with the common parts for ST
platforms.
Change-Id: I1bc4e6835dba4230359ea9b26d736791e27258aa
Signed-off-by: Yann Gautier <yann.gautier@st.com>
