BL2_AT_EL3 is an overloaded macro which has two uses:
1. When BL2 is entry point into TF-A(no BL1)
2. When BL2 is running at EL3 exception level
These two scenarios are not exactly same even though first implicitly
means second to be true. To distinguish between these two use cases we
introduce new macros.
BL2_AT_EL3 is renamed to RESET_TO_BL2 to better convey both 1. and 2.
Additional macro BL2_RUNS_AT_EL3 is added to cover all scenarious where
BL2 runs at EL3 (including four world systems).
BREAKING CHANGE: BL2_AT_EL3 renamed to RESET_TO_BL2 across the
repository.
Change-Id: I477e1d0f843b44b799c216670e028fcb3509fb72
Signed-off-by: Arvind Ram Prakash <arvind.ramprakash@arm.com>
Signed-off-by: Maksims Svecovs <maksims.svecovs@arm.com>
Add page table translation entry for secure uart so that logs from
secure partition can be routed via the same.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I3416d114bcee13824a7d0861ee54fb799e154897
Revert submission 14286-uart_segregation
Reason for revert: Need to wait for companion patches in CI and UEFI/Linux to be upstreamed.
Reverted Changes:
I8574b31d5:feat(sgi): add page table translation entry for se...
I8896ae05e:feat(sgi): route TF-A logs via secure uart
I39170848e:feat(sgi): deviate from arm css common uart relate...
Change-Id: I9bec02496f826e184c6efa643f869b2eb3b52539
Add page table translation entry for secure uart so that logs from
secure partition can be routed via the same.
Signed-off-by: Rohit Mathew <rohit.mathew@arm.com>
Change-Id: I8574b31d5d138d9f94972deb903124f8c5b70ce4
On a multi-chip platform, the boot CPU on the first chip programs the
TZC controllers on all the remote chips. Define a memory region map for
the TZC controllers for all the remote chips and include it in the BL2
memory map table.
In addition to this, for SPM_MM enabled multi-chip platforms, increase
the number of mmap entries and xlat table counts for EL3 execution
context as well because the shared RAM regions and GIC address space of
remote chips are accessed.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I6f0b5fd22f9f28046451e382eef7f1f9258d88f7
Allow the access of system registers and nor2 flash memory region
from s-el0. This allows the secure parititions residing at s-el0
to access these memory regions.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I3887a86770de806323fbde0d20fdc96eec6e0c3c
Remove the 'ARM_' prefix from the macros defining the CPER buffer memory
and replace it with 'CSS_SGI_' prefix. These macros are applicable only
for platforms supported within plat/sgi. In addition to this, ensure
that these macros are defined only if the RAS_EXTENSION build option is
enabled.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I44df42cded18d9d3a4cb13e5c990e9ab3194daee
The SGI platform defines the macro PLAT_ARM_MEM_PROT_ADDR which
indicates that the platform has mitigation for cold reboot attacks.
However, the flash memory used for the mem_protect region was not
mapped. This results in a crash when an OS calls PSCI MEM_PROTECT.
To fix this map the flash region used for mem_protect.
Change-Id: Ia494f924ecfe2ce835c045689ba8f942bf0941f4
Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
Following merge of patchset [1] the spm_mm_boot_info_t structure is
included in few platform files unconditionally even when SPM_MM option
is disabled.
[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/2647
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I68bc034c9348b5d9bcfd2e5217b781df5ad1b369
Before adding any new SPM-related components we should first do
some cleanup around the existing SPM-MM implementation. The aim
is to make sure that any SPM-MM components have names that clearly
indicate that they are MM-related. Otherwise, when adding new SPM
code, it could quickly become confusing as it would be unclear to
which component the code belongs.
The secure_partition.h header is a clear example of this, as the
name is generic so it could easily apply to any SPM-related code,
when it is in fact SPM-MM specific.
This patch renames the file and the two structures defined within
it, and then modifies any references in files that use the header.
Change-Id: I44bd95fab774c358178b3e81262a16da500fda26
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
There are two different implementations of Secure Partition
management in TF-A. One is based on the "Management Mode" (MM)
design, the other is based on the Secure Partition Client Interface
(SPCI) specification. Currently there is a dependency between their
build flags that shouldn't exist, making further development
harder than it should be. This patch removes that
dependency, making the two flags function independently.
Before: ENABLE_SPM=1 is required for using either implementation.
By default, the SPCI-based implementation is enabled and
this is overridden if SPM_MM=1.
After: ENABLE_SPM=1 enables the SPCI-based implementation.
SPM_MM=1 enables the MM-based implementation.
The two build flags are mutually exclusive.
Note that the name of the ENABLE_SPM flag remains a bit
ambiguous - this will be improved in a subsequent patch. For this
patch the intention was to leave the name as-is so that it is
easier to track the changes that were made.
Change-Id: I8e64ee545d811c7000f27e8dc8ebb977d670608a
Signed-off-by: Paul Beesley <paul.beesley@arm.com>
The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.
So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.
Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Many parts of the code were duplicating symbols that are defined in
include/common/bl_common.h. It is better to only use the definitions in
this header.
As all the symbols refer to virtual addresses, they have to be
uintptr_t, not unsigned long. This has also been fixed in bl_common.h.
Change-Id: I204081af78326ced03fb05f69846f229d324c711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Use full include paths like it is done for common includes.
This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.
Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.
This also prevents problems like cyclic dependencies.
Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
The definitions in bl1/bl1_private.h and bl2/bl2_private.h are useful for
platforms that may need to access them.
Change-Id: Ifd1880f855ddafcb3bfcaf1ed4a4e0f121eda174
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Update some asserts that refer to #defines that only occur in
ARM platforms, preventing this code to be used on other platforms.
Instead, use a platform agnostic name, and update all the existing
users.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Enforce full include path for includes. Deprecate old paths.
The following folders inside include/lib have been left unchanged:
- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}
The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).
For example, this patch had to be created because two headers were
called the same way: e0ea0928d5 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a2 ("drivers: add tzc380 support").
This problem was introduced in commit 4ecca33988 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.
Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.
Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Add platform specific changes needed to add support for the RAS
feature on SGI575 platform, including adding a mapping for the
CPER buffer being used on SGI575 platform.
Change-Id: I01a982e283609b5c48661307906346fa2738a43b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
The secure partition manager reserves chunks of memory which are used
for the S-EL0 StandaloneMM image and the buffers required for
communication between the Non-Secure world with the StandaloneMM
image. Add the memory chunks to relevant arrays for mapping the
regions of memory with corresponding attributes.
Change-Id: If371d1afee0a50ca7cacd55e16aeaca949d5062b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>
Remove the redundant SGI functions which map memory
for BL1 and BL2.
Change-Id: I651a06d0eb6d28263a56f59701bb3815f1ba93dc
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Add support for System Guidance for Infrastructure platform SGI575.
Change-Id: I0125c2ed4469fbc8367dafcc8adce770b6b3147d
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>
