Add a new method to write the processor device identified by _HID
ACPI0007, that is preferred over the Processor OpCode since ACPI 6.0.
Fixes booting arm using ACPI only since the Processor OpCode isn't
found valid by the Linux kernel.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Allocate memory for ACPI tables in generic acpi code. When ACPI wasn't
installed in other places, install the ACPI table using BLOBLISTs.
This allows non x86 platforms to boot using ACPI only in case the
EFI loader is being used, since EFI is necessary to advertise the location
of the ACPI tables in memory.
TEST: Booted QEMU SBSA (no QFW) using EFI and ACPI only.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Since ACPI 2.0 the RSDT is deprecated and the XSDT should be preferred.
Until now the RSDT and XSDT entries were keept in sync as all platforms
that installed ACPI tables placed them below 4GiB and thus the address
would fit into the 32bit RSDT.
On platforms that do not have usable DRAM below 4GiB, like QEMU sbsa,
the RSDT cannot be used. Allow both RSDT and XSDT to be null and only
fill those tables that are present in acpi_add_table().
TEST: Fixes a crash on QEMU sbsa and allows to boot on QEMU sbsa.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Allow other architectures to use acpi_create_mcfg_mmconfig as well
by moving the function prototype to common code.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
The SoC can implement acpi_fill_iort to update the IORT table.
Add a helper function to fill out the NAMED_COMPONENT node.
TEST=Run FWTS V24.03.00 on RPi4 and round no problems.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Return the ACPI table revision in acpi_get_table_revision() for
PPTT and GTDT. Match both to ACPI 6.2.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
The FADT structure found in U-Boot represents FADT revision 6 and the
GICC and GICD structures defined in U-Boot are based on ACPI revision
6.3.
Bump the table revision to fix FWTS failures seen on aarch64.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Add a new method to acpi_ops to let drivers fill out ACPI MADT.
The code is unused for now until drivers implement the new ops.
TEST: Booted on QEMU sbsa using driver model generated MADT.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Add generic ACPI code to generate
- MADT GICC
- MADT GICD
- MADT GICR
- MADT GIC ITS
- PPTT processor
- PPTT cache
as commonly used on arm platforms.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Add the interrupt flag used in ACPI GTDT table as define.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Moritz Fischer <moritzf@google.com>
When ACPI is enabled on arm it will use the getinfo function to fill
the SPCR ACPI table.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Moritz Fischer <moritzf@google.com>
Rename ACPI tables MADR to MADT.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Write MADT in common code and let the SoC fill out the body by
calling acpi_fill_madt() which must be implemented at SoC level.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Write the FADT in common code since it's used on all architectures.
Since the FADT is mandatory all SoCs or mainboards must implement the
introduced function acpi_fill_fadt() and properly update the FADT.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
This moves the SPCR and DBG2 table generation into common code, so that
they can be used by architectures other than x86.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
This driver should not generally be present in SPL, even if misc devices
are enabled. Update the Makefile rule accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow MMC init when clock support is not enabled in a particular phase.
Refactor the setting of priv->emmc_clk so it is a bit clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
When MMC booting fails it is sometimes hard to figure out what went
wrong as there is no error code. It isn't even clear which MMC device
was chosen, since SPL can have its own numbering.
Add some debugging to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are currently four symbols here, so drop the word 'two'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Separate BSS is current mandatory on armv8 but this is not useful for
early boot phases. Add support for the combined BSS.
Use an #ifdef to avoid using CONFIG_SPL_BSS_START_ADDR which is not
valid in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The sprintf() etc. functions are supposed to return the length of the
string written, but do not. Fix this by checking the amount of buffer
space used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Oliver Gaskell <Oliver.Gaskell@analog.com> says:
ADSP-SC5xx is a series of ARM-based DSPs.
This comprises the armv7 based SC57x, SC58x and SC594 series, and the
armv8 based SC598.
This patch series includes configurations, init code, and minimal DTs
to enable Analog Devices' evaluation boards for these SoCs to boot
through SPL and into U-Boot Proper, as well as devicetree schemas for
the added DTs.
This patch series depends on ("arm: Add Analog Devices SC5xx Machine
Type") (https://lists.denx.de/pipermail/u-boot/2024-April/552043.html)
Adds support for Analog Devices' SC589-MINI board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC589-EZKIT board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
- Memory configuration
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC594-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Adds support for Analog Devices' SC598-SOM-EZLITE board. Includes:
- Board specific configs in mach-sc5xx/Kconfig
- Board-specific Kconfig and environment in board/adi/
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Moves common options between all SC5xx series boards to the ARCH_SC5XX
option instead of duplicating them.
Also, it was possible to select multiple of the SoC support options.
Given a U-Boot binary can only support a single platform, this moves
the SoC selection to a `choice`, making them mutually exclusive.
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add devicetree schema for the clock tree on Analog Devices SC5xx series
SoCs.
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add minimal device tree for Analog Devices' SC598-SOM-EZLITE board.
This patch depends on Patches 01 and 07, for sc5xx.dtsi and
sc598-som.dtsi respectively.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add minimal device tree for Analog Devices' SC598-SOM-EZKIT board, and
the SC598 SoM.
This patch depends on patch 01, for sc5xx.dtsi.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Add minimal device tree for Analog Devices' SC594-SOM-EZLITE board.
This patch depends on Patches 01 and 05, for sc5xx.dtsi and
sc594-som.dtsi respectively.
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
