The FriendlyElec NanoPi R2S Plus is a single-board computer based on
Rockchip RK3328 SoC. It features e.g. 1 GB DDR4 RAM, 32 GB eMMC,
SD-card, 2x GbE LAN, optional M.2 SDIO Wi-Fi and 2x USB 2.0 host.
Features tested on a NanoPi R2S Plus 2309:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for Cool Pi GenBook, it works as a carrier board
connect with CM5 SOM.
Specification:
- Rockchip RK3588
- LPDDR5X 8/32 GB
- eMMC 64 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for RTL8852BE Wireless connection
- PCIE M.2 M Key for NVME connection
- eDP panel with 1920x1080
Tested by Armbian boot on USB disk.
Change-Id: I4d9b8572dc7c400077dde666633f3fea1b47dd03
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Qnap TS433 is a 4-bay NAS based around the RK3568.
Two SATA bays are connected to the RK3568's own SATA controllers while
the other two are connected to a JMicron SATA controller living on the
PCIe bus.
It provides one 2.5Gb and one 1Gb ethernet port as well as 3 usb ports.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Coreboot provides the CMOS layout in the tables it passes to U-Boot.
Use that to build an editor for the CMOS settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sphinx writes a warning if a page is included twice in the table of
contents. Use references instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Neha Malcom Francis <n-francis@ti.com>
Sphinx warns if a page is added to the table of contents twice.
Add a reference instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The Emcraft Systems NavQ+ kit is a mobile robotics platform
based on NXP i.MX8 MPlus SoC.
The following interfaces and devices are enabled:
- eMMC
- Gigabit Ethernet (through eQOS interface)
- SD-Card
- UART console
The device tree file is taken from upstream Linux Kernel
through OF_UPSTREAM
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jan Kiszka <jan.kiszka@siemens.com> says:
This adds support for the new IOT2050 SM variant, introduces a sysinfo
driver which also permits SMBIOS support and switches the board to
OF_UPSTREAM. There are some further fixes for the boards included as well.
Not yet included is configuration support for DMA isolation via the PVU as
this depends on not yet merged DT bindings and another overlay.
[trini: This is just the first 10 patches in the series for now]
Link: https://lore.kernel.org/r/cover.1729577070.git.jan.kiszka@siemens.com
Main differences between the new variant and Advanced PG2:
1. Arduino interface is removed. Instead, an new ASIC is added for
communicating with PLC 1200 signal modules.
2. USB 3.0 type A connector is removed, only USB 2.0 type A connector is
available.
3. DP interface is tailored down. Instead, to communicate with the
PLC 1200 signal modules, a USB 3.0 type B connector is added but the
signal is not USB.
4. DDR size is increased to 4 GB.
5. Two sensors are added, one tilt sensor and one light sensor.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
[Jan: rebased over OF_UPSTREAM]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Due to new DDR size introduction, the current logic of determining the
DDR size is not able to get the correct size.
Instead, the DDR size is determined by the FSBL(SEBOOT) then passed to
u-boot through the scratchpad info.
The SEBoot version must be >= D/V01.04.01.02 to support this change.
Also now for some variants, the DDR size may > 2GB, so borrow some code
from the TI evm to iot2050 to support more than 2GB DDR.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Patrick Rudolph <patrick.rudolph@9elements.com> says:
Based on the existing work done by Simon Glass this series adds
support for booting aarch64 devices using ACPI only.
As first target QEMU SBSA support is added, which relies on ACPI
only to boot an OS. As secondary target the Raspberry Pi4 was used,
which is broadly available and allows easy testing of the proposed
solution.
The series is split into ACPI cleanups and code movements, adding
Arm specific ACPI tables and finally SoC and mainboard related
changes to boot a Linux on the QEMU SBSA and RPi4. Currently only the
mandatory ACPI tables are supported, allowing to boot into Linux
without errors.
The QEMU SBSA support is feature complete and provides the same
functionality as the EDK2 implementation.
The changes were tested on real hardware as well on QEMU v9.0:
qemu-system-aarch64 -machine sbsa-ref -nographic -cpu cortex-a57 \
-pflash secure-world.rom \
-pflash unsecure-world.rom
qemu-system-aarch64 -machine raspi4b -kernel u-boot.bin -cpu cortex-a72 \
-smp 4 -m 2G -drive file=raspbian.img,format=raw,index=0 \
-dtb bcm2711-rpi-4-b.dtb -nographic
Tested against FWTS V24.03.00.
Known issues:
- The QEMU rpi4 support is currently limited as it doesn't emulate PCI,
USB or ethernet devices!
- The SMP bringup doesn't work on RPi4, but works in QEMU (Possibly
cache related).
- PCI on RPI4 isn't working on real hardware since the pcie_brcmstb
Linux kernel module doesn't support ACPI yet.
Link: https://lore.kernel.org/r/20241023132116.970117-1-patrick.rudolph@9elements.com
Add support for Arm sbsa [1] v0.3+ that is supported by QEMU [2].
Unlike other Arm based platforms the machine only provides a minimal
FDT that contains number of CPUs, ammount of memory and machine-version.
The boot firmware has to provide ACPI tables to the OS.
Due to this design a full DTB is added here as well that allows U-Boot's
driver to properly function. The DTB is appended at the end of the U-Boot
image and will be merged with the QEMU provided DTB.
In addition provide documentation how to use, enable binman to fabricate both
ROMs that are required to boot and add ACPI tables to make it full compatible
to the EDK2 reference implementation.
The board was tested using Fedora 40 Aarch64 Workstation. It's able
to boot from USB and AHCI or network.
Tested and found working:
- serial
- PCI
- xHCI
- Bochs display
- AHCI
- network using e1000e
- CPU init
- Booting Fedora 40
1: Server Base System Architecture (SBSA)
2: https://www.qemu.org/docs/master/system/arm/sbsa.html
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Features tested on a ODROID-M1S 8GB rev1.0 20230906:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Clarify the usage of SCMI specific device tree to use with
stm32mp15_defconfig and with OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support for the Libre Computer aml-s905d3-cc "Solitude" board:
https://libre.computer/products/aml-s905d3-cc/
The Solitude board has a Credit Card form factor, similar to the
the previous "Le Potato" card, but with the Amlogic A311D SoC,
MIPI DSI and CSI connectors. PoE header and a single USB2 Type-C
connector replacing the microUSB one for power and USB 2.0.
The board has an embedded SPI NOR flash, and EFI Capsule support
is added.
The GUID is dynamically generated for the board, to get it:
=> efidebug capsule esrt
========================================
ESRT: fw_resource_count=1
ESRT: fw_resource_count_max=1
ESRT: fw_resource_version=1
[entry 0]==============================
ESRT: fw_class=4302C3CB-2502-5EFE-87E0-894A8A322893
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
========================================
On the host (with the aml_encrypt_g12a result binary):
$ eficapsule --guid 4302C3CB-2502-5EFE-87E0-894A8A322893 -i 1 u-boot.bin u-boot.cap
On the board (from USB disk containing u-boot.cap at root):
=> load usb 0:1 $kernel_addr_r u-boot.cap
=> efidebug capsule update $kernel_addr_r
The binary will then be flashed on the SPI.
Link: https://lore.kernel.org/r/20240920-u-boot-topic-libre-computer-solitude-alta-v1-2-8915b108840b@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for the Libre Computer aml-a311d-cc "Alta" board:
https://libre.computer/products/aml-a311d-cc/
The Alta board has a Credit Card form factor, similar to the
the prvevious "Le Potato" card, but with the Amlogic A311D SoC,
MIPI DSI and CSI connectors. PoE header and a single USB2 Type-C
connector replacing the microUSB one for power and USB 2.0.
The board has an embedded SPI NOR flash, and EFI Capsule support
is added.
The GUID is dynamically generated for the board, to get it:
=> efidebug capsule esrt
========================================
ESRT: fw_resource_count=1
ESRT: fw_resource_count_max=1
ESRT: fw_resource_version=1
[entry 0]==============================
ESRT: fw_class=17E07D9D-4D91-53F4-8780-1D91F279C1A5
ESRT: fw_type=unknown
ESRT: fw_version=0
ESRT: lowest_supported_fw_version=0
ESRT: capsule_flags=0
ESRT: last_attempt_version=0
ESRT: last_attempt_status=success
========================================
On the host (with the aml_encrypt_g12a result binary):
$ eficapsule --guid 17E07D9D-4D91-53F4-8780-1D91F279C1A5 -i 1 u-boot.bin u-boot.cap
On the board (from USB disk containing u-boot.cap at root):
=> load usb 0:1 $kernel_addr_r u-boot.cap
=> efidebug capsule update $kernel_addr_r
The binary will then be flashed on the SPI.
Link: https://lore.kernel.org/r/20240920-u-boot-topic-libre-computer-solitude-alta-v1-1-8915b108840b@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The TF-A URL was updated, as a result the name of the
directory changed as part of the new git URL and not
all the referenced directories were updated.
Fixes: 0ec0207fe0 ("Update the ARM trusted firmware git URL")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The primary upstream URL for tf-a has moved, in some cases
things like tags are not always pushed to the old URL so
update the URLs to the primary upstream project URL.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Add Android bootflow support for AM62X SK EVM board with
new android boot method.
To build for AM62x for Android, we use the
am62x_a53_android.config fragment when building A53 bootloaders:
$ make am62x_evm_a53_defconfig
$ make am62x_a53_android.config
$ make
Co-developed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
AST2700 SoCs integrates a Ibex 32-bits RISC-V core as the boot MCU
for the first stage bootloader execution, namely SPL.
This patch implements the preliminary base to successfully run SPL
on this RV32-based MCU to the console banner message.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The process here is almost identical to the Dragonboard 410c, we've come
full circle!
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
eMMC is enabled on E850-96 board now. Mention that in the board
documentation.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Rock 5 ITX is a board in ITX form factor using the RK3588 SoC
It can be powered either by 12V, ATX power-supply or PoE.
Notable peripherals are the 4 SATA ports, M.2 M-Key slot, M.2 E-key slot,
2*2.5Gb PCIe-connected Ethernet NICs.
Display options are 2*HDMI, DP via USB-c, eDP + 2*DSI via PCB connectors.
USB ports are 4*USB3 + 2*USB2 on the back panel and 2-port front-panel
connector.
Schematics for the board can be found on
- https://dl.radxa.com/rock5/5itx/radxa_rock_5_itx_X1100_schematic.pdf
- https://dl.radxa.com/rock5/5itx/v1110/radxa_rock_5itx_v1110_schematic.pdf
The naming scheme with the dashes follows Dragan's comment on the mainline
devicetree commit:
"the name of this board deviates from the standard Radxa naming scheme,
which is something like "ROCK <number><letter>" thus, "rock-5a" is
fine, but it should be "rock-5-itx", simply because there's a space
between "5" and "ITX" in "ROCK 5 ITX"
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The CM3588 NAS by FriendlyElec pairs the CM3588 compute module, based
on the Rockchip RK3588 SoC, with the CM3588 NAS Kit carrier board.
Features tested on a CM3588 NAS Kit with 8GB RAM 64GB eMMC module:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
The two hw revisions use different io-voltage for Ethernet PHY and can
be identified using GPIO4_C4:
- v1.1.1: x (internal pull-down)
- v2.1: PHY_RESET (external pull-up)
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both hw revisions.
Minimal DTs that includ DT from dts/upstream is added to support booting
from both hw revision and only set Ethernet PHY io-voltage when the hw
revision is detected at runtime. A side-affect of this is that defconfig
show OF_UPSTREAM=n, however dts/upstream DTs is used for this board.
Features tested on Orange Pi 3B 4GB (v1.1.1 and v2.1):
- SD-card boot
- eMMC boot
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB host
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ZERO 3W/3E is an ultra-small, high-performance single board
computer based on the Rockchip RK3566, with a compact form factor and
rich interfaces.
Implement rk_board_late_init() to set correct fdtfile env var and
board_fit_config_name_match() to load correct FIT config based on what
board is detected at runtime so a single board target can be used for
both board models.
Features tested on a ZERO 3W 8GB v1.11:
- SD-card boot
- eMMC boot
- USB gadget
- USB host
Features tested on a ZERO 3E 4GB v1.2:
- SD-card boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
version based on the RK3568 SoC and an industrial version based on the
RK3568J SoC.
Features tested on ROCK 3B 8GB v1.51 (both variants):
- SD-card boot
- eMMC boot
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa ROCK S0 is a single-board computer based on the Rockchip RK3308B
SoC in an ultra-compact form factor. Add a board target for the board.
Features tested on a ROCK S0 v1.2 with 512 MiB RAM and 8 GiB eMMC:
- SD-card boot
- eMMC boot
- Ethernet
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for packaging the TIFS Stub as it's required for basic Low
Power Modes like Deep Sleep.
The reason it is packaged using binman and not inherently as part of the
DM firmware is because for HS devices, customer owns the customer key
and only customer has access to it.
DM is release by TI, Since TI doesn't have access to the customer key it
cannot have a component that is signed by customer key.
Hence, it's left as part of binman to be signed and packaged.
While at it, also make sure it's documented in phycore-am62x
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
* Include the actual common documentation about the TIFS Stub and role
it plays to enable Low Power Modes in the platform.
* Add the AM62x boot flow to show at which point the TIFS Stub actually
gets loaded.
* Mention the TIFS Stub in the TISPL image format.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Since AM62x, AM62P and AM62A all use similar boot flows and their low
power mode s/w ARCH is also similar in the way that they make use of the
TIFS Stub, update their documentation to show where TIFS Stub is.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Use the new boot_firmwares labels that help make documentation more
specific as to which firmwares are used in which devices
Signed-off-by: Dhruva Gole <d-gole@ti.com>
* Add documentation to briefly explain the role of TIFS Stub in relevant
K3 SoC's.
* Shed light on why TIFS Stub isn't package with the DM firmware itself.
* Modify the platform docs wherever the TIFS Stub documentation applies.
* Also, refactor and add a few new labels to help split the firmware
documentation chunks. This will make it easier to include them one by
one wherever applicable
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # verdin-am62
Before adding more files, move the bootstd docs into a new directory,
with an index.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The NanoPi R6S is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, 32GB eMMC storage,
one RTL8211F 1GbE and two RTL8125 2.5GbE Ethernet ports, one USB 2.0
Type-A and one USB 3.0 Type-A port, a HDMI port, a 12-pin GPIO FPC
connector, a fan connector, IR receiver as well as some buttons and LEDs.
Add initial support for this board using the upstream devicetree sources.
Kernel commit:
f1b11f43b3e9 ("arm64: dts: rockchip: Add support for NanoPi R6S")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Sebastian Kropatsch <seb-dev@mail.de>
