- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
Enable the 'eeprom' command with support for EEPROM layout for Turris
Omnia. Enable the i2c-eeprom driver so that the EEPROM is accessed via
driver model.
Signed-off-by: Marek Behún <kabel@kernel.org>
For board revisions where the WAN ethernet PHY reset GPIO is controllable
via MCU we currently insert a phy-reset-gpios property into the ethernet
controller node. The mvneta driver parses this property and uses the
GPIO to reset the PHY.
But this phy-reset-gpios property is not a valid DT binding in upstream
kernel. Instead, a reset-gpios property should be inserted into the
ethernet PHY node. This correct DT binding is supported by the DM ETH PHY
U-Boot driver.
Insert the reset-gpios property into the WAN PHY node instead the
phy-reset-gpios property in WAN ETH node so that Linux will correctly use
the reset GPIO.
Enable the CONFIG_DM_ETH_PHY config option so that U-Boot will also use
the correct DT property.
Note: currently there are 4 ethernet controller drivers parsing the
wrong DT property: dwc_eth_qos, fex_mxc, mvneta and mvpp2. We should
convert all relevant device-trees to use reset-gpios so that we can get
rid of these drivers parsing this property.
Fixes: 1da53ae26a ("arm: mvebu: turris_omnia: Add support for design with SW reset signals")
Signed-off-by: Marek Behún <kabel@kernel.org>
Turris Omnia defconfig is nearing image size limit. Disable ext4 write
support to reserve space for more important stuff.
This reduces the size of the KWB image by ~19 KiB.
If in the future U-Boot supports compressing itself and decompressing
on load, we may enable this again.
Signed-off-by: Marek Behún <kabel@kernel.org>
Enable PCA953x GPIO expander driver in DH i.MX8MP DHCOM PDK2 configuration.
The PCA9539 GPIO expander is used on production DH i.MX8MP DHCOM SoM rev.200.
This is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align the
two configurations.
Fixes: 9de599ec3d ("arm64: dts: imx8mp: Update i.MX8MP DHCOM SoM DT to production rev.200")
Signed-off-by: Marek Vasut <marex@denx.de>
Enable 'cat' command to print file from filesystem to stdout.
Enable 'xxd' command to hexdump file from filesystem to stdout.
Signed-off-by: Marek Vasut <marex@denx.de>
The board has the TCA9554 I2C GPIO expander chip for expansion
board presence detection logic.
Enable the relevant I2C GPIO drivers.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Enable the clock/pinctrl drivers for these two SoCs. Previously left out
due to only being used on the db410c and db820c respectively which both
have their own board code. We can still boot these with most features
working without that board code.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Sam Day <me@samcday.com>
The Lenovo IdeaPad Yoga 11 is a hybrid laptop/tablet Windows RT-based
computer released in late 2012. The device uses a 1.3 GHz quad-core
Nvidia Tegra 3 chipset with 2 GB of RAM, features a 11.6 inch 1366x768
screen and 32/64 GB of internal memory that can be supplemented with
a microSDXC card slot, full size SD card slot and 2 full size USB 2.0
ports.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Surface RT is a hybrid tablet computer developed and manufactured
by Microsoft and shipped with Windows RT. The tablet uses a 1.3 GHz
quad-core Nvidia Tegra 3 chipset with 2 GB of RAM, features 10.8
inch 1366x768 screen and 32/64 GB of internal memory that can be
supplemented with a microSDXC card giving up to 200 GB of
additional storage.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
WEXLER Tab 7t is a mini tablet computer developed by WEXLER that
runs the Android operating system. The device features a 7.0-inch
(180 mm) HD display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM,
8, 16 or 32 GB of storage that can be supplemented with a microSDXC
card giving up to 64 GB of additional storage and a full size USB
port.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Asus Eee Pad Transformer family are 2-in-1 detachable/slider
tablets developed by Asus that run the Android operating system.
The Eee Pad Transformers feature a 10.1-inch (260 mm) display,
an Nvidia Tegra 2 dual-core chip, 1 GB of RAM, and 16/32 GB of storage.
Transformers board derives from Nvidia Ventana development board.
This patch brings support for all 3 known T20 Transformers:
- Asus Eee Pad Transformer TF101
- Asus Eee Pad Transformer TF101G
- Asus Eee Pad Slider SL101
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Jiaxun Yang <jiaxun.yang@flygoat.com> says:
Hi all,
This series enabled qemu-xtensa board.
For dc232b CPU it needs to be built with toolchain[1].
This is a side product of me investigating architectures
physical address != virtual address in U-Boot. Now we can
get it covered under CI and regular tests.
VirtIO devices are not working as expected, due to U-Boot's
assumption on VA == PA everywhere, I'm going to get this fixed
later.
My Xtensa knowledge is pretty limited, Xtensa people please
feel free to point out if I got anything wrong.
Thanks
[1]: https://github.com/foss-xtensa/toolchain/releases/download/2020.07/x86_64-2020.07-xtensa-dc232b-elf.tar.gz
This feature is not present on older Chromebooks, so disable the
setting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We currently don't have any boards enabling CONFIG_EFI_RT_VOLATILE_STORE.
We do have EFI selftests testing the feature though, so enable it in
all the sandbox platforms and test the functionality properly
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Now that am335x_evm boots OK on the Beaglebone black, drop the latter
and update the docs to cover the change.
Also add a few updates about 'make fit' and drop the note about the
security review, as U-Boot's verified boot has had quite extensive
review now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This causes a hang, so disable it. Unfortunately the RAM-size fix does
not resolve the problem and I am unsure what is wrong. As soon as the
cache is enabled the board appears to hang.
Fixes: 6d8cdfd153 ("rockchip: spl: Enable caches to speed up checksum validation")
Signed-off-by: Simon Glass <sjg@chromium.org>
Set a size limit for this board so that we get a build error if it grows
too much.
Note that the limit is approximately, since it does not include the FDT,
microcode and fdtmap, which can change in size. However this board is
fairly stable, so overflowing this limit will likely result in the image
not fitting in the ROM space available for U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
This cannot be enabled early in boot since some other init is needed.
At this point it is unclear exactly what init is needed, so disable
the debug UART to avoid a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21310
- Enable SPL DTO application support for i.MX8MP DHCOM PDK2.
- Migrate imx8mn_bsh_smm_s2 and imx6ulz_bsh_smm_m2 to OF_UPSTREAM.
- Drop redundant imports with dts/upstream.
- Miscellaneous improvements for Gateworks i.MX8M boards.
Enable SPL DTO support to apply matching SoM specific DTOs to cater
for the SoM differences in DH i.MX8MP DHCOM PDK2 configuration. This
is already enabled in DH i.MX8MP DHCOM PDK3 configuration so align
the two configurations.
Fixes: ad1158c50e ("arm64: dts: imx8mp: Switch to DT overlays for i.MX8MP DHCOM SoM")
Signed-off-by: Marek Vasut <marex@denx.de>
Migrate imx8mn_bsh_smm_s2 and imx8mn_bsh_smm_s2pro boards to OF_UPSTREAM.
Signed-off-by: Patrick Barsanti <patrick.barsanti@amarulasolutions.com>
Tested-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
It is good to be aware what information is shared via smbios interface
that's why enable it by default.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable ICSSG driver, DP83869 phy driver, REMOTEPROC and PRU_REMOTEPROC
in am64x_evm_a53_defconfig. All these configs are needed for ICSSG
driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Jayesh Choudhary <j-choudhary@ti.com> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
Introduce the initial configs needed to support the J722S SoC family.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
