Anurag Dutta <a-dutta@ti.com> says:
Hi All,
In u-boot, hbmc is broken and has been removed from j7200
configs. This series re-enables the hbmc driver and introduces a series
of hyperflash boot fixes. At present, in u-boot, the parent device (fss)
gets registered as a syscon device. This is done because the MMIO
mux driver in u-boot did not support the mux functionality when the
parent device is not a syscon. In this series, we make relevant changes
in the hbmc driver as well as dts' so that we can use the reg-mux driver for
selecting the appropriate state of the mux.
Test logs:
1) j721e-idk-gw hyperflash boot test: https://gist.github.com/anuragdutta731/50aae6fec707a3ffad6d985de6757fe4
2) j7200-evm hyperflash boot test: https://gist.github.com/anuragdutta731/c3a4d60f8bfd9c425d6c44b36eb7322b
Link: https://lore.kernel.org/r/20241129113136.383277-1-a-dutta@ti.com
Instead of bloating the defconfig with CONFIG_CMD_*, move J7 devices to
start using TI_COMMON_CMD_OPTIONS.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
Wadim Egorov <w.egorov@phytec.de> says:
This implements capsule updates for all our K3 SoMs for
eMMC, OSPI NOR and uSD cards.
We can use capsule updates to update the bootloader on all our
supported flash devices.
Link: https://lore.kernel.org/r/20241127121736.1525948-1-w.egorov@phytec.de
Enable raw & on disk capsule updates and provide configs required
for updating MTD devices. Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Enables ESM configs for j721s2 and disables them for AM68 as AM68
includes J721s2 configs by default.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This reverts commit 1fdf53ace1, reversing
changes made to e5aef1bbf1.
I had missed that this caused too much size growth on rcar3_salvator-x.
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass <sjg@chromium.org> says:
This includes various patches towards implementing the VBE abrec
bootmeth in U-Boot. It mostly focuses on SPL tweaks and adjusting what
fatures are available in VPL.
Link: https://lore.kernel.org/r/20241207172412.1124558-1-sjg@chromium.org
With VBE we want to use FIT in all phases of the boot. Add Kconfig
options to support this.
Disable the options for sandbox_vpl for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The env variable "SN" is used to store the serial number on DH electronics
SoMs. New SoMs will use the variable "dh_som_serial_number". To ensure
compatibility, these env variables are synchronized. This is achieved
using callback functions.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Bryan Brattlof <bb@ti.com> says:
Hello Everyone!
This small series converts TI's AM65x reference board to use
CONFIG_OF_UPSTREAM and removes the unused device tree files from
arch/arm/dts.
Because it's the last board using a AM65x without enabling OF_UPSTREAM
it allows us to also remove all the SoC FDT files as well and keep a
single version of the SoC's DT files in the dts/upstream directory going
forward.
Link: https://lore.kernel.org/r/20241121-am65x-v1-0-fe87aff1b5fc@ti.com
Rather than rely on manual updates from the arch/arm/dts directory,
enable CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the am65x reference board.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Aniket Limaye <a-limaye@ti.com> says:
This series adds OPP_LOW spec data in k3_avs driver and enables a config
option to select the OPP_LOW performance point.
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
The default j7200 devicetree and k3_avs driver set OPP_NOM spec
frequency and voltage.
In the board init file, if K3_OPP_LOW config is enabled, Check if
OPP_LOW AVS voltage read from efuse is valid and update frequency (A72
and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec.
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
Test logs:
https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075
- With series applied on master and CONFIG_K3_OPP_LOW enabled in
j7200_evm_r5_defconfig
- Logs shown with and without efuse register programmed for OPP_0
(Errors out if OPP_0 not found, programs OPP_LOW spec if found)
- Voltage update verified using 'i2c md 0x4c 0xe' in u-boot
- Frequency update verified using 'k3conf clock dump' in linux
Link: https://lore.kernel.org/r/20241119003617.1871183-1-a-limaye@ti.com
Define new CONFIG_K3_OPP_LOW under arm/mach-k3/r5/Kconfig and add
default value to j7200_evm_r5_defconfig
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Enable AVS support on J784S4 along with regulator.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZ0m53AAKCRDKSWXLKUoM
Ie4PAJ4r7EHkSngpW3QdBEb15aLxN1pC4ACcC9DDGGn04kCTChpv0CEi/kRLUBU=
=Veyg
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2025.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2025.04-rc1
binman:
- Separate binman description from main DT
zynqmp:
- Enable binman for ZynqMP platforms
- DT sync with Linux v6.12
- Update usb5744 hub for SOMs
common:
- Drop SPL_FIT_GENERATOR support
versal2
- Enable OPTEE layers
ospi:
- Refactor the flash reset functionality
pytest:
- Fix tcminit mode handling
PSCI reset is not implemented in Exynos850 EL3 firmware. Disable it to
fix the reset in cases where it can be used, e.g. when running EFI
selftest.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a small utility for displaying some information about U-Boot and the
hardware it's running on in a similar fashion to the popular neofetch
tool for Linux [1].
While the output is meant to be useful, it should also be pleasing to
look at and perhaps entertaining. The ufetch command aims to bring this
to U-Boot, featuring a colorful ASCII art version of the U-Boot logo.
[1]: https://en.wikipedia.org/wiki/Neofetch
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8560-QRD
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
USB host support on ZYNQMP KRIA SOM needs onboard USB
hub driver for handling reset GPIO and for i2c initialization
sequence.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20241126041238.1969723-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable PCIe/NVMe support on Data Modul i.MX8M Mini eDM SBC. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
The YModem support in SPL was never really used on this device,
the SDP support is much more convenient on i.MX8M Mini based
hardware. Replace the YModem support with SDP support.
The SDP can be utilized by forcing the board into SDP boot mode
by grounding test point right next to silkscreen label U30, and
then by using mfgtools 'uuu -brun spl flash.bin' once the device
enumerates on host system USB bus. The SDP capable USB port is
available on the USB micro-B port on the base board.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Deduplicate defconfigs for all Data Modul i.MX8M eDM SBC systems by factoring
out the common parts into generic imx8m_data_modul.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is almost
identical for all Data Modul i.MX8M eDM SBC systems, except for slight
alignment in DEBUG_UART and SYS_PBSIZE.
Signed-off-by: Marek Vasut <marex@denx.de>
Currently, the PCI subsystem selects the small "region 2" (which starts at 0x7000000)
as bus_addr/phys_addr. As a consequence, the BAR0 on PCIe video card cannot be initialized,
because it simply doesn't fit into 0x1000000 bytes size of "region 2".
U-Boot should use "region 1" instead (the one which starts at 0x60090000), because
it has much bigger size (0xFF70000), and easily accomodates BAR0 of the video card.
Linux kernel also uses 0x60090000 as bus_start/phys_start.
Signed-off-by: Yuri Zaporozhets <yuriz@vodafonemail.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To restore MMC boot, enable SPL_SYS_MMCSD_RAW_MODE and recover
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Fixes: 2a00d73d08 ("spl: mmc: Try to clean up raw-mode options")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
With the move from script based booting to using bootmeth a lot of
environment variables have changed. To always use the default environment
it is recommendable to erase the environment stored in the SPI flash.
This can be done with the 'env erase' sub-command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
u-boot.itb has been generated via mkimage_fit_atf.sh but it is on the way
out that's why convert it's description to binman.
Compare to script binman description is not able to configure BL31 and BL32
load/entry addresses which should be done separately.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/90b613796aee38158252c8bb1dfc3da0420f089d.1730452668.git.michal.simek@amd.com
There is necessary to do some steps to compose boot images. These steps
were in scripts in layers for a while. That's why introduce description via
binman to simplify wiring and remove all scripting around.
This should make sure that everybody is up2date with the latest versions.
The first step is to create fit image with DTBs with descriptions in
configuration node which is written as regular expression to match all SOM
versions.
Description is there for k24 and k26 in spite of low level psu_init
configuration is different. The reason is that it goes to u-boot.itb image
which is the same for k24 and k26.
u-boot.itb is another image which is generated. It is normally generated
via arch/arm/mach-zynqmp/mkimage_fit_atf.sh but this script is supposed to
be deprecated.
FIT image by purpose is using 64bit addresses to have default option to
move images to high DDR (above 4GB). TF-A and TEE are optional components
but in the most cases TF-A is present all the time and TEE(OP-TEE) is used
by some configurations too.
3rd generated image is boot.bin with updated user field which contains
version number. This image can be used with updated Image Selector
which supports A/B update mechanisms with rollback protection.
4th image is image.bin which binary file which contains boot.bin and
u-boot.itb together and can be programmed via origin Image Selector.
This image can be also used for creating one capsule which contains both
boot images (in SPL boot flow).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/35bc47a4a4799c5f5dbea56a45340a2810538330.1730452668.git.michal.simek@amd.com
Make use of OF_UPSTREAM which uses Linux dts.
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Anand Gore <anand.gore@broadcom.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/23573
Android:
- bootstd: Implement bootimage v2 support
- bootstd: Support non-A/B in bootmeth_android
- Migrate VIM3 and VIM3L to use bootmeth_android
- bootstd: Additional test for bootimage v2
- bootstd: Optimize load time when reading partitions
The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
