- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
Support old DDR3 training code on Turris Omnia, selectable via EEPROM
field.
Users experiencing DDR3 initialization failures or random crashes of the
operating system due to incorrect DDR3 configuration can select the old
DDR3 training implementation to fix those issues by setting the EEPROM
field "Use old DDR training":
eeprom update "Use old DDR training" 1
Signed-off-by: Marek Behún <kabel@kernel.org>
Some Turris Omnia boards experience memory issues, and by
experimentation we found that some of these issues can be solved by
slowing DDR speed.
Add a new field in the extended EEPROM information structure, ddr_speed.
Support several values in this field (for now 1066F, 1333H, and the
default, 1600K) and use it to overwrite the DDR topology parameters
used by the DDR training algorithm.
Signed-off-by: Marek Behún <kabel@kernel.org>
Implement Turris Omnia EEPROM layout for the 'eeprom' command.
When the 'eeprom' command (with layout support) is enabled, we can now
use the 'eeprom print' and 'eeprom update' commands, for example:
=> eeprom print
Magic constant 34a04103
RAM size in GB 2
Wi-Fi Region
CRC32 checksum cecbc2a1
Signed-off-by: Marek Behún <kabel@kernel.org>
For board revisions where the WAN ethernet PHY reset GPIO is controllable
via MCU we currently insert a phy-reset-gpios property into the ethernet
controller node. The mvneta driver parses this property and uses the
GPIO to reset the PHY.
But this phy-reset-gpios property is not a valid DT binding in upstream
kernel. Instead, a reset-gpios property should be inserted into the
ethernet PHY node. This correct DT binding is supported by the DM ETH PHY
U-Boot driver.
Insert the reset-gpios property into the WAN PHY node instead the
phy-reset-gpios property in WAN ETH node so that Linux will correctly use
the reset GPIO.
Enable the CONFIG_DM_ETH_PHY config option so that U-Boot will also use
the correct DT property.
Note: currently there are 4 ethernet controller drivers parsing the
wrong DT property: dwc_eth_qos, fex_mxc, mvneta and mvpp2. We should
convert all relevant device-trees to use reset-gpios so that we can get
rid of these drivers parsing this property.
Fixes: 1da53ae26a ("arm: mvebu: turris_omnia: Add support for design with SW reset signals")
Signed-off-by: Marek Behún <kabel@kernel.org>
The older i.MX8M Mini Verdin SoMs may came with 20 MHz SPI CAN controller
oscillator, the newer SoMs always use 40 MHz oscillator. Handle both by
overriding the oscillator frequency just before booting the kernel.
These are the known variants with 20 MHz oscillator:
- 0055, V1.1A, V1.1B, V1.1C and V1.1D, use a 20MHz oscillator
- 0059, V1.1A and V1.1B, use a 20MHz oscillator
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Various minor fixes and improvements:
* Fix Qualcomm SPMI v5 support
* Move default environment to a file
* Add support for special pins (e.g ufs/mmc reset/data pins)
* IPQ moves to OF_UPSTREAM and receives some cleanup and MAINTAINERS
changes
* Add a reset driver for devices without PSCI
* msm8916 USB clock improvements for mobile devices
Make use of CONFIG_DEFAULT_ENV_FILE and move the default qcom
environment to a file under board/qualcomm.
This is much cleaner and means we don't need to recompile on changing
the environment.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The Lenovo IdeaPad Yoga 11 is a hybrid laptop/tablet Windows RT-based
computer released in late 2012. The device uses a 1.3 GHz quad-core
Nvidia Tegra 3 chipset with 2 GB of RAM, features a 11.6 inch 1366x768
screen and 32/64 GB of internal memory that can be supplemented with
a microSDXC card slot, full size SD card slot and 2 full size USB 2.0
ports.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Surface RT is a hybrid tablet computer developed and manufactured
by Microsoft and shipped with Windows RT. The tablet uses a 1.3 GHz
quad-core Nvidia Tegra 3 chipset with 2 GB of RAM, features 10.8
inch 1366x768 screen and 32/64 GB of internal memory that can be
supplemented with a microSDXC card giving up to 200 GB of
additional storage.
Tested-by: Jethro Bull <jethrob@hotmail.com>
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
WEXLER Tab 7t is a mini tablet computer developed by WEXLER that
runs the Android operating system. The device features a 7.0-inch
(180 mm) HD display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM,
8, 16 or 32 GB of storage that can be supplemented with a microSDXC
card giving up to 64 GB of additional storage and a full size USB
port.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Asus Eee Pad Transformer family are 2-in-1 detachable/slider
tablets developed by Asus that run the Android operating system.
The Eee Pad Transformers feature a 10.1-inch (260 mm) display,
an Nvidia Tegra 2 dual-core chip, 1 GB of RAM, and 16/32 GB of storage.
Transformers board derives from Nvidia Ventana development board.
This patch brings support for all 3 known T20 Transformers:
- Asus Eee Pad Transformer TF101
- Asus Eee Pad Transformer TF101G
- Asus Eee Pad Slider SL101
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Jiaxun Yang <jiaxun.yang@flygoat.com> says:
Hi all,
This series enabled qemu-xtensa board.
For dc232b CPU it needs to be built with toolchain[1].
This is a side product of me investigating architectures
physical address != virtual address in U-Boot. Now we can
get it covered under CI and regular tests.
VirtIO devices are not working as expected, due to U-Boot's
assumption on VA == PA everywhere, I'm going to get this fixed
later.
My Xtensa knowledge is pretty limited, Xtensa people please
feel free to point out if I got anything wrong.
Thanks
[1]: https://github.com/foss-xtensa/toolchain/releases/download/2020.07/x86_64-2020.07-xtensa-dc232b-elf.tar.gz
Tim Harvey <tharvey@gateworks.com> says:
This series will automatically add /chosen/kaslr-seed to the dt if
DM_RNG is enabled
during the boot process.
If RANDOMIZE_BASE is enabled in the Linux kernel instructing it to
randomize the virtual address at which the kernel image is loaded, it
expects entropy to be provided by the bootloader by populating
/chosen/kaslr-seed with a 64-bit value from source of entropy at boot.
If we have DM_RNG enabled populate this value automatically when
fdt_chosen is called. We skip this if ARMV8_SEC_FIRMWARE_SUPPORT
is enabled as its implementation uses a different source of entropy
that is not yet implemented as DM_RNG. We also skip this if
MEASURED_BOOT is enabled as in that case any modifications to the
dt will cause measured boot to fail (although there are many other
places the dt is altered).
As this fdt node is added elsewhere create a library function and
use it to deduplicate code. We will provide a parameter to overwrite
the node if present.
For our automatic injection, we will use the first rng device and
not overwrite if already present with a non-zero value (which may
have been populated by an earlier boot stage). This way if a board
specific ft_board_setup() function wants to customize this behavior
it can call fdt_kaslrseed with a rng device index of its choosing and
set overwrite true.
Note that the kalsrseed command (CMD_KASLRSEED) is likely pointless now
but left in place in case boot scripts exist that rely on this command
existing and returning success. An informational message is printed to
alert users of this command that it is likely no longer needed.
Note that the Kernel's EFI STUB only relies on EFI_RNG_PROTOCOL for
randomization and completely ignores the kaslr-seed for its own
randomness needs (i.e the randomization of the physical placement of
the kernel). It gets weeded out from the DTB that gets handed over via
efi_install_fdt() as it would also mess up the measured boot DTB TPM
measurements as well.
Use the fdt_kaslrseed function to deduplicate code doing the same thing.
Note that the kalsrseed command (CMD_KASLRSEED) is likely pointless now
but left in place in case boot scripts exist that rely on this command
existing and returning success. An informational message is printed to
alert users of this command that it is likely no longer needed.
Note that the Kernel's EFI STUB only relies on EFI_RNG_PROTOCOL for
randomization and completely ignores the kaslr-seed for its own
randomness needs (i.e the randomization of the physical placement of
the kernel). It gets weeded out from the DTB that gets handed over via
efi_install_fdt() as it would also mess up the measured boot DTB TPM
measurements as well.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Akash Gajjar <gajjar04akash@gmail.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Devarsh Thakkar <devarsht@ti.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Now that am335x_evm boots OK on the Beaglebone black, drop the latter
and update the docs to cover the change.
Also add a few updates about 'make fit' and drop the note about the
security review, as U-Boot's verified boot has had quite extensive
review now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add better logging for power init so that CONFIG_LOG_ERROR_RETURN can
be enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Padmarao is leaving Microchip soon, and suggested that I should take
over maintaining the Icicle in U-Boot in his stead.
Suggested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Kernel Image and DTB files are supposed to be picked from the rootfs
of the SD Card, this fails in legacy boot flow because bootpart is set
to 1:1. Fix it.
Fixes: a200f428b5 ("board: ti: am62x: Add am62x_beagleplay_* defconfigs and env file")
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Chirag Shilwant <c-shilwant@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Unfortunately when enabling FDT fixups for the AM62x family of SoCs and
moving TF-A to the bottom of RAM we missed the BeaglePlay. This is
causing Linux's memory allocator to clobber TF-A and break its boot.
Enable OF_SYSTEM_SETUP to fixup the kernel's FDT to inform it of the
actual location of the firmware
CC: Andrew Davis <afd@ti.com>
CC: Nishanth Menon <nm@ti.com>
CC: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Chirag Shilwant <c-shilwant@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
Specifically board_interface_eth_init will handle the configuration of
GPR1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Due to supply chain issues Venice boards use either a DP83867 or a
GPY111 RGMII PHY. We already print an identifier for the DP83867 so add
one for the GPY111 to better identify what PHY is on a board:
Example:
Net: GPY111 eth0: ethernet@30be0000 [PRIME]
Net: DP83867 eth0: ethernet@30be0000 [PRIME]
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Extensive testing has shown that at higher temperatures operating
without a GSC backup battery, the GSC needs a small delay after
releasing the I2C SDA/SCL pins before it is ready to handle I2C
requests.
Add a delay to avoid errors such as:
wait_for_sr_state: Arbitration lost sr=93 cr=80 state=2020
i2c_init_transfer: failed for chip 0x20 retry=0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks System Controller (GSC) has a voltage supervisor which is
disabled by default. On older boards we want to maintian this but on
newer boards we wish to enable the voltage supervisor.
The Gateworks System Controller (GSC) can disable the board primary
power supply by driving a pin to a FET high. On older board models
the leakage of the GSC may exceed the leakage of the FET causing this
signal slowly rise when the GSC battery is low and the board is in a
powered down state resulting in the board being kept in a disabled
state.
Newer boards have a hardware fix to avoid this leakage and thus should
enable the voltage supervisor.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
When ICSSG driver is enabled (CONFIG_TI_ICSSG_PRUETH=y) set
storage_interface and fw_dev_part env variables.
These variables need be set appropriately in order to load different
ICSSG firmwares needed for ICSSG driver. By default the storage
interface is mmc and the partition is 1:2. User can modify this based on
their needs.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Jayesh Choudhary <j-choudhary@ti.com> says:
Hello there,
This series add the U-Boot support for our new platform of K3-SOC
family - J722S-EVM which is a superset of AM62P. It shares the same
memory map and thus the nodes are being reused from AM62P includes
instead of duplicating the definitions.
Some highlights of J722S SoC (in addition to AM62P SoC features) are:
- Two Cortex-R5F for Functional Safety or general-purpose usage and
two C7x floating point vector DSP with Matrix Multiply Accelerator
for deep learning.
- Vision Processing Accelerator (VPAC) with image signal processor
and Depth and Motion Processing Accelerator (DMPAC).
- 7xUARTs, 3xSPI, 5xI2C, 2xUSB2, 2xCAN-FD, 3xMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 5xMcASP for audio,
4xCSI-RX for Camera, 1 PCIe Gen3 controller, USB3.0 eCAP/eQEP,
ePWM, among other peripherals.
TRM: <https://www.ti.com/lit/zip/sprujb3>
Schematics: <https://www.ti.com/lit/zip/sprr495>
Boot test log:
<https://gist.github.com/Jayesh2000/0313e58fde377f877a9a8f1acc2579ef>
Introduce the basic files needed to support the TI J722S family of SoCs.
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM69
SK.
TODO: possibly make the struct's sk specific.
TODO: add doc commit (and make sure doc is sk/NOR specific, and add OSIP
boot mode)
TODO: update doc to show sk defconfig when building
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
BeagleBoneAI64.
Note this involved creating BeagleBoneAI64's own beagleboneai64.h board
header file instead of reusing j721e_evm's.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62px
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM62x
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
BeaglePlay.
Note this involved creating BeaglePlay's own beagleplay.h board header file
instead of reusing am62_evm's.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the
SK-TDA4VM.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Define the firmware components updatable via EFI capsule update, including
defining capsule GUIDs for the various firmware components for the AM64x
SK.
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no need to reread the EEPROM multiple times in different stages
to detect the RAM size. We can do this once at an early stage and let
higher stages decode memory nodes using fdtdec.
Make sure to pass fixup memory nodes before passing to u-boot stage.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Pull in ti/k3_dfu.env for dfu_alt_info_ram in SPL stage.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Copy fixed-partitions nodes from U-Boot device tree to OS device tree.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Test whether this system is compatible with STM32MP15xx DHCOM SoM,
if so, test whether R292 pull up is populated on pin PC3, which is
an indication that the second MAC chip, KS8851-16MLL, is populated.
Use this information to patch 'status' DT property into the second
ethernet MAC DT node and enable/disable the MAC on systems where
the chip is/isn't populated respectively.
Use spl_perform_fixups() to patch the U-Boot proper DT from SPL and
ft_board_setup() to patch Linux DT from U-Boot proper. This way both
software components are configured the same way.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZnBfewAKCRDKSWXLKUoM
Ib/7AJ0cn3q7lMpxbSbRj33oftI8Vy8+owCeN35Nl8TN9l/DHbfusER4uVfnOVw=
=YMIB
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
AMD/Xilinx changes for v2024.10-rc1
common:
- spl: Introduce SoC specific init function
xilinx:
- Enable FF-A and NVMEM
- Rename spl_board_init() to spl_soc_init()
zynqmp:
- DT alignments
- Enable reset from SPL
- Enable USB3 for KD240
- Align multiboot register on Kria for proper reboot
- Allow multiboot environment write even in saved environment
- Move zynqmp commands from board/ to arch/
- Clean up xilinx_zynqmp.h
versal:
- Do not prioritize boot device if driver is not enabled
versal-net:
- Setup location for redundant variables in SPI
versal2:
- Add support for new SOC
mmc:
- Fix tap delay for SD on Versal NET
spi:
- Add SPI_NOR_OCTAL_READ flag for mx66uw2g345gx0 flash part
gpio:
- Cover MODEPIN firmware dependency
This commit enables SPL to reset the CPU via PMU-firmware. The usual
reset mechanism requires bl31 to be loaded which may not be the case in
SPL.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Link: https://lore.kernel.org/r/20240607092608.712996-2-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch corrects the mio and pll configuration registers for using usb3
on the kd240 starter kit. Without this patch, the usb3 to sd card bridge does
not initialize correctly and u-boot is unable to find the OS located on the
kd240 starter kit sd card.
In addition, this patch correctly configures mio76 and mio77 as gpio pins
which are used as reset gpio pins on the kd240 starter kit.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20240604083854.2033917-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
