It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the mxc-i2c
driver will fail to support scl-gpios and sda-gpios for
i2c bus recovery.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This TU currently relies on getting a declaration of schedule()
through some nested include. Include the proper header directly.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some I2C slave devices are read-only and don't even answer with NACK.
For example FD65x segment LED controllers.
Make them usable with i2c-gpio,sda-output-only that are already supported
by Linux 6.3+.
Signed-off-by: Alex Shumsky <alexthreed@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for the following Maxim chips using the existing PCA954x
driver:
- MAX7356
- MAX7357
- MAX7358
- MAX7367
- MAX7368
- MAX7369
All added Maxim chips behave like the PCA954x, where a single SMBUS byte
write selects up to 8 channels to be bridged to the primary bus.
Tested using the MAX7358.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Now that this is always 1, remove it and the associated dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Now that this is always 0, remove it and the associated dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop some old code from the mxc_i2c and ddr/fsl drivers. This will allow
removal of very old common I2C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The TXFIFO register of LPI2C only has one byte length, and if the length
of the data that needs to be read exceeds 256 bytes, it needs to be
written to TXFIFO multiple times.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Instead of using the hard-coded bus speed value I2C_SPEED_STANDARD_RATE,
use the actual configured bus speed. This way the bus speed doesn't
change suddenly after calling the imx_lpi2c_probe_chip() function for
example.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Newer Samsung SoCs (including newer Exynos, ExynosAuto, Google Tensor)
still use these IPs, or slightly newer versions of it.
Make these drivers available on these platforms by guarding
EXYNOS4/EXYNOS5 specific code behind their configs, and using CCF for
clocks on other platforms.
Tested S3C I2C driver on Exynos7885.
This along with extended clock driver should enable S3C I2C on
Exynos850.
Signed-off-by: David Virag <virag.david003@gmail.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is no reason to use goto and just call return. Better is to call
return directly which is done for some if/else parts.
Also make no sense to setup ret to -ETIMEDOUT and then to 0.
Return timeout directly.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is no reason to have any pointer to GD that's why remove it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop all duplicate newlines. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for optional arb and pmic clock for i2c provided in upstream
linux DTSI.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove <common.h> from this driver directory and when needed
add missing include files directly.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Support for the Qualcomm Generic Interface (GENI) I2C interface
found on newer Qualcomm SoCs.
The Generic Interface (GENI) is a firmware based Qualcomm Universal
Peripherals (QUP) Serial Engine (SE) Wrapper which can support multiple
bus protocols depending on the firmware type loaded at early boot time
based on system configuration.
It also supports the "I2C Master Hub" which is a single function Wrapper
that only FIFO mode I2C.
It replaces the fixed-function QUP Wrapper found on older SoCs.
The geni-se.h containing the generic GENI Serial Engine registers defines
is imported from Linux.
Only FIFO mode is implemented, neither SE DMA nor GPI DMA are implemented.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Marek Vasut <marek.vasut+renesas@mailbox.org> says:
Rename R-Mobile to Renesas all over the place because the chips are
made by Renesas, while only a subset of them is from the R-Mobile line.
Rename ARCH_RMOBILE to ARCH_RENESAS because all the chips are made
by Renesas, while only a subset of them is from the R-Mobile
line.
Use the following command to perform the rename:
"
$ git grep -l 'ARCH_RMOBILE' | xargs -I {} sed -i 's@ARCH_RMOBILE@ARCH_RENESAS@g' {}
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
This driver supports the I2C module on the Renesas RZ/G2L (R9A07G044)
SoC, also known as the RIIC module.
This patch is based on both the u-boot driver in the Renesas RZ BSP
3.0.5 release [1] (commit 7fcc1fdc2534), and the Linux v6.7 driver
(commit 0dd3ee311255).
Support for deblocking the I2C bus is included as this may be needed
after triggering a reset via the Power Management IC (PMIC) over I2C
(the PMIC asserts the reset line before the SoC completes the I2C write
transaction with obvious bus locking effects). If the SDA line is
observed to be low during initialisation, we automatically attempt to
deblock.
[1]: https://github.com/renesas-rz/renesas-u-boot-cip
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The "i2cbcdev" sneaked in when implementing this function for the
bootcounter use case. Obviously the intention was to use prop_name
instead.
Fixes: b483552773 (i2c: Implement i2c_get_chip_by_phandle())
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Now that we have time conversion defines from in time.h there is no need
for each driver to define their own version.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com> #at91
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> #qcom geni
Reviewed-by: Stefan Bosch <stefan_b@posteo.net> #nanopi2
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This new function enhances the i2c_get_chip*() toolbox by implementing a
variant that does not require a chip_addr. Instead, the desired device
is pointed to by a phandle.
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In SPL probing of the designware_i2c device on the StarFive VisionFive 2
board fails with
dw_i2c: mode 0, ic_clk 1000000, speed 100000,
period 10 rise 1 fall 1 tlow 5 thigh 4 spk 0
dw_i2c: bad counts. hcnt = -4 lcnt = 4
device_probe: i2c@12050000 failed to probe -22
When changing the offset for the high phase from 7 to 3 the device is
probed correctly. This now matches the value from the Linux driver.
Without this fix the memory size of the StarFive VisionFive 2 board cannot
be read from EEPROM.
Fixes: e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
first version is only support standard mode.
remove this judgment to support standard/fast/fast plus mode.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Changes for v2:
- add commit message
Reviewed-by: Heiko Schocher <hs@denx.de>
Allwinner seems to typically stick to a common MMIO memory map for
several SoCs, but from time to time does some breaking changes, which
also introduce new generations of some peripherals. The last time this
happened with the H6, which apart from re-organising the base addresses
also changed the clock controller significantly. We added a
CONFIG_SUN50I_GEN_H6 symbol back then to mark SoCs sharing those traits.
Now the Allwinner D1 changes the memory map again, and also extends the
pincontroller, among other peripherals.
To mark this generation of SoCs, add a CONFIG_SUNXI_GEN_NCAT2 symbol,
this name is reportedly used in the Allwinner BSP code, and prevents us
from inventing our own name.
Add this new symbol to some guards that were already checking for the H6
generation, since many features are shared between the two (like the
renovated clock controller).
This paves the way to introduce a first user of this generation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
U-Boot's generic GPIO_EXTRA_HEADER is a convenience symbol to allow code
to more easily include platform specific GPIO headers. This should not
be needed in a DM world anymore, since the generic GPIO framework
handles that nicely.
For Allwinner boards we still need to deal with non-DM GPIO in the SPL,
but this should become the exception, not the rule.
Make this more obvious by removing the definition of GPIO_EXTRA_HEADER,
and just force every legacy user of platform specific GPIO to include
the new sunxi_gpio.h header explicitly. Everyone doing so should feel
ashamed and should find a way to avoid it from now on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
lib/acpi/acpigen.o is only compiled into SPL when SPL_ACPIGEN is enabled.
Update several files which reference these functions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox unit tests in U-Boot proper load a test device tree to have some
devices to work with. In order to do the same in SPL, we must enable
SPL_OF_REAL. However, we already have SPL_OF_PLATDATA enabled. When
generating platdata from a devicetree, it is expected that we will not need
devicetree access functions (even though SPL_OF_CONTROL is enabled). This
expectation does not hold for sandbox, so allow user control of
SPL_OF_REAL.
There are several places in the tree where conditions involving OF_PLATDATA
or OF_REAL no longer function correctly when both of these options can be
selected at the same time. Adjust these conditions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Errors were handled only if an I2C transfer timed out
and received a NACK which is very unlikely. This commit
changes the condition such that errors are handled if
an I2C transfer times out or received a NACK.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
The MVTWSI controller can act either as a master or slave device. When
acting as a master, the FSM is driven by the CPU. As a slave, the FSM is
driven by the bus directly. In what is (apparently) a safety mechanism,
if the bus transitions our FSM in any improper way, the FSM goes to a
"bus error" state (0x00). I could find no documented or experimental way
to get the FSM out of this state, except for a controller reset.
Since U-Boot only uses the MVTWSI controller as a bus master, this
feature only gets in the way: we do not care what happened on the bus
previously as long as the bus is ready for a new transaction. So, when
trying to start a new transaction, check for this state and reset the
controller if necessary.
Note that this should not be confused with the "deblocking" technique
(used by the `i2c reset` command), which involves pulsing SCL repeatedly
if SDA is found to be held low, in an attempt to force the bus back to
an idle state. This patch only resets the controller in case something
else had previously upset it, and (in principle) results in no
externally-observable change in behavior.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
MT7981 actually uses MediaTek I2C controller v3 instead of v1.
This patch adds support for I2C controller v3 fix fixes the I2C usability
for MT7981.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
As the Designware_i2c_pci.c uses ACPI APIs, If some SoCs (StarFive
JH7110) contain Designware i2c and PCI but do not use ACPI,
This file cannot be compiled. So add a new Kconfig for
designware_i2c_pci.c, which depends on ACPIGEN
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
