It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
The default PCA9451 BUCK2 volt is 0.6 V for LPDDR4x VDDQ. The codes
are actually used for reworking to LPDDR4 which needs VDDQ at 1.1 V.
So remove it to avoid LPDDR4x issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fix build error "undefined reference to `is_warm_boot'" when
ls1021atsn and ls1021atwr boards are built with CONFIG_SPL=y and
CONFIG_DEEP_SLEEP=n.
Signed-off-by: Benjamin Lemouzy <blemouzy@centralp.fr>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable dynamic settings to mmcdev and mmcroot for i.MX8MQ-EVK
Since we are here, clean up the including headers
Signed-off-by: Peng Fan <peng.fan@nxp.com>
buf was used as destination and as parameter to sprintf
which triggers an undefined behaviour.
This commit removes this usage of sprintf and uses strcat
to append strings to buf variable.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Improve "mmcautodetect=yes" boot mode autodetection to able to use it
if CONFIG_ENV_IS_NOWHERE=y is used for i.MX9 SoCs and i.MX93 EVK board.
If both CONFIG_ENV_IS_IN_MMC=y and CONFIG_ENV_IS_NOWHERE=y are in the
defconfig, CONFIG_ENV_IS_IN_MMC=y will be overiden default
CONFIG_ENV_IS_NOWHERE settings.
Goal is in this patch to able to use the boot mode autodetection
if defconfig use only CONFIG_ENV_IS_NOWHERE=y option
(without CONFIG_ENV_IS_IN_MMC) for any i.MX9 SoC.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
With CONFIG_DM_USB, there is no longer the need for any USB board code
anymore.
Remove the unneeded USB board code.
While at it, also remove the uneeeded CONFIG_USB_MAX_CONTROLLER_COUNT
option.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Simon Glass <sjg@chromium.org> says:
When the SPL build-phase was first created it was designed to solve a
particular problem (the need to init SDRAM so that U-Boot proper could
be loaded). It has since expanded to become an important part of U-Boot,
with three phases now present: TPL, VPL and SPL
Due to this history, the term 'SPL' is used to mean both a particular
phase (the one before U-Boot proper) and all the non-proper phases.
This has become confusing.
For a similar reason CONFIG_SPL_BUILD is set to 'y' for all 'SPL'
phases, not just SPL. So code which can only be compiled for actual SPL,
for example, must use something like this:
#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
In Makefiles we have similar issues. SPL_ has been used as a variable
which expands to either SPL_ or nothing, to chose between options like
CONFIG_BLK and CONFIG_SPL_BLK. When TPL appeared, a new SPL_TPL variable
was created which expanded to 'SPL_', 'TPL_' or nothing. Later it was
updated to support 'VPL_' as well.
This series starts a change in terminology and usage to resolve the
above issues:
- The word 'xPL' is used instead of 'SPL' to mean a non-proper build
- A new CONFIG_XPL_BUILD define indicates that the current build is an
'xPL' build
- The existing CONFIG_SPL_BUILD is changed to mean SPL; it is not now
defined for TPL and VPL phases
- The existing SPL_ Makefile variable is renamed to SPL_
- The existing SPL_TPL Makefile variable is renamed to PHASE_
It should be noted that xpl_phase() can generally be used instead of
the above CONFIGs without a code-space or run-time penalty.
This series does not attempt to convert all of U-Boot to use this new
terminology but it makes a start. In particular, renaming spl.h and
common/spl seems like a bridge too far at this point.
The series is fully bisectable. It has also been checked to ensure there
are no code-size changes on any commit.
Jerome Forissier <jerome.forissier@linaro.org> says:
Miscellaneous fixes made when developing the lwIP series [1]. They are
posted separately since they make sense on their own. Subsequent
versions of the lwIP series will contain a squashed version of this one.
[1] http://patchwork.ozlabs.org/project/uboot/list/?series=420712&state=%2A&archive=both
Prefix the flash status codes (ERR_*) with FL_ in order to avoid clashes
with third-party libraries. Case in point: including the lwIP library
header file <lwip/err.h> which defines err_enum_t as an enum with values
being ERR_*.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Add back low drive mode 1866mts ddr timing file, no need
CONFIG_IMX9_LOW_DRIVE_MODE anymore, using runtime selection.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove unused CONFIG_IMX9_LOW_DRIVE_MODE kconfig and
imx93_11x11_evk_ld_defconfig.
Remove the ld timing file.
The LD mode support will be added back with runtime detection later.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Use runtime voltage selection for LD/OD/ND mode.
2. According to latest PE/TE report, the voltages of VDD_SOC for
LD and ND mode need add 50mv margin, so LD voltage is 0.75v->0.8v,
ND voltage is 0.8v->0.85v.
3. Use TOFF_DEB to differentiate new trimmed pmic and old pmic
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since we use SPEED GRADE fuse to set A55 frequency, remove the
set_arm_core_low_drive_clk function which has hard coded frequency.
And adjust clock_init called sequence and split it to early and late
functions.
Set the authen register in early function, because CCF driver checks
NS bit.
Set bus and core clock in late function, because the fuse read and
SoC type/rev depend on ELE.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace the static CONFIG_IMX9_LOW_DRIVE_MODE with runtime target
voltage mode by checking the part's SPEED GRADE fuse.
SPL will configure to highest A55 speed which is indicated by the SPEED
fuse and select corresponding voltage mode.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Kconfig symbols SYS_ARCH, SYS_CPU, SYS_SOC, SYS_VENDOR and
SYS_BOARD are defined in arch/Kconfig as having type string, and most
board files simply amend those definition with suitable
default "foo"
or
default "foo" if BAR
stanzas. But some also include a redundant repetition of the type.
Homogenize the code base by removing those lines.
Generated by
find arch/*/ board -name Kconfig | xargs perl -i -g -pe 's/(config SYS_(ARCH|CPU|SOC|VENDOR|BOARD)\n)\s*string\n/\1/gs'
with the trailing slash in arch/*/ ensuring that arch/Kconfig itself
is not found.
This does not change boards which add a prompt string, e.g.
string "Board name"
because I think those change the semantics of the symbol into being
user-settable.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
This allows boards to fixup / overwrite DT model string when booting OS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
After adding the U_BOOT_LONGHELP macro some new commands came in still
that were not making use if it. Switch these cases over and in a few
places add missing newlines as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
