Provide a defconfig for booting the phycore-am62x via Ethernet.
We need a separate defconfig because the AM62x has not enough internal
SRAM to support all boot sources.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The ACPI IORT and ACPI MADT needs to use the same IDs when referencing
GIC ITS. The GIC-v3 ITS driver uses dev_seq(dev) to generate a unique ID
for the MADT, but qemu sbsa-ref hardcodes it.
Currently it's not the same ID, breaking interrupt routing on the OS.
Don't assume it's 0 and fetch it from the device instead.
TEST: Fixes non working IRQs in QEMU sbsa-ref.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Note that this undoes the changes of commit cf6d4535cc ("x86:
emulation: Disable bloblist for now") as that was intended only for the
release due to time.
Currently in j721e_init.c we check which firewalls to remove using
the board configuration (e.g CONFIG_TARGET_J721E_R5_EVM). We do this
as J721e and J7200 have different IP and firewalls but use the same
SoC definition (SOC_K3_J721E) even though they are different SoCs.
The idea was they would be similar enough that they both could use
the same SoC config to help with common code sharing. Board checks
would then be used differentiate.
This has grown far too messy to maintain any more, especially now
that there is more than one board using J721e (EVM, SK, Beagle AI64).
As differentiation is done based on board, every one of these boards
would have to have checks added for them. Instead let's split J7200
support out from J721e like how normal new SoC support is done.
This patch touches several subsystems and could not be split much better
as when we add SOC_K3_J7200 we want to make use of it in all spots that
once used the combined SOC_K3_J721E so we can turn off SOC_K3_J721E when
building for J7200 boards.
Signed-off-by: Andrew Davis <afd@ti.com>
Jeremy Compostella <jeremy.compostella@intel.com> says:
Introduces a new configuration option X86_RUN_64BIT_NO_SPL to allow
building U-Boot as a 64-bit binary without using the SPL (Secondary
Program Loader). The motivation is to simplify the boot process for
specific x86-based platforms that do not require SPL, such as those
booting directly from a 64-bit coreboot firmware.
Link: https://lore.kernel.org/r/87bjtyutkp.fsf@jcompost-mobl.amr.corp.intel.com
When set_dfu_alt_info() is called, interface can be NULL when called for
the EFI capsule, so check it before calling it with strcmp().
Fixes: 12ea40d29d ("ARM: meson: add support for Libre Computer aml-s905d3-cc")
Fixes: 9e6e6b034b ("ARM: meson: add support for Libre Computer aml-a311d-cc")
Fixes: 75c87c6cbc ("board: libre-computer: aml-s805x-cc: Enable capsule updates")
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20250403-u-boot-fix-set-dfu-alt-info-interface-v1-1-1fdd12463186@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Manorit Chawdhry <m-chawdhry@ti.com> says:
The series adds support for J742S2 family of SoCs. Also adds J742S2 EVM
Support and re-uses most of the stuff from the superset device J784s4.
This device is a subset of J784S4 and shares the same memory map and
thus the code is being reused from J784S4 to avoid duplication.
It initially cleans up the J784s4 and AM69 files so that they can be
re-usable for j742s2 and then it introduces J742S2.
The DT for the following SoC will be coming to U-boot during 6.13 Sync
so the series is kept as RFC till then.
Here are some of the salient features of the J742S2 automotive grade
application processor:
The J742S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive, ADAS and industrial
applications requiring AI at the network edge. This SoC extends the K3
Jacinto 7 family of SoCs with focus on raising performance and
integration while providing interfaces, memory architecture and compute
performance for multi-sensor, high concurrency applications.
Some changes that this devices has from J784S4 are:
* 4x Cortex-A72 vs 8x Cortex-A72
* 3x C7x DSP vs 4x C7x DSP
* 4 port ethernet switch vs 8 port ethernet switch
* 2 DDR controller vs 4 DDR controller
Test logs:
https://gist.github.com/manorit2001/f7df0e8cca1e9973b4361f0559c6f53d
Link: https://lore.kernel.org/r/20250317-b4-upstream-j742s2-v4-0-4ba88bfd357a@ti.com
Based off j784s4 configs with delta changes for J742S2
[ Add AVS support for J742S2 ]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Include the U-boot device tree files needed to boot the board.
[ DDR config ]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Refactor J784s4 ddr file to a common file which uses the
superset device to allow reuse in j742s2-evm which uses the subset part.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. In the case of OF_SEPARATE this is
the default so we do not need to do anything here normally to enforce
this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Christian Marangi <ansuelsmth@gmail.com> says:
This little series adds initial support for Airoha AN7581 SoC.
With the help of some backport patch, this use OF_UPSTREAM
directly.
Posting this to have the targer and the very basic driver.
Ethernet, SNAND and eMMC support is already ready downstream
and will be posted shortly after this gets approved.
Having the first driver ready permits to separately push
dedicate series for SNAND, eMMC and Ethrnet as they all depends
on basic support of clock and reset and nothing else.
Link: https://lore.kernel.org/r/20250314185941.27834-1-ansuelsmth@gmail.com
Add initial support for Airoha AN7581 SoC. This adds the initial Kconfig
and Makefile entry for the SoC, an U-Boot specific DTSI and initial config
for it. Also add the initial code for CPU and RAM initialization.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The first 4 block copy channels and rings on AM62P support
High Capacity Block Copy. These channels have approximately
3x improvement over the normal Block copy channels when doing
DDR-to-DDR copy.
Currently, during allocation these channels do not have a
separate interface and are allocated with normal BCDMA channels.
Latest TIFS and DM firmware adds support for differentiating these
High Capcity resources. This update is for allocating these new
resource type to different hosts with below mentioned scheme.
--------------------- --------------- ------------- ----------------
Resource A53_2 MCU_R5 WKUP_R5
--------------------- --------------- ------------- ----------------
BCDMA HC CHAN [4] => 2 (Primary) 1 (Primary) 1 (Primary)
BCDMA HC CHAN RING [4] => 2 (Primary) 1 (Primary) 1 (Primary)
BCDMA CHAN [4] => 18 (Primary) 2 (Primary) 6 (Primary)
BCDMA CHAN RING[4] => 18 (Primary) 2 (Primary) 6 (Primary)
Signed-off-by: Sparsh Kumar <sparsh-kumar@ti.com>
Signed-off-by: Sebin Francis <sebin.francis@ti.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Remove leftover code from Milk-V Mars CM and Mars CM Lite boards that do
not exist in upstream Linux Kernel devicetree-rebasing. These will be re-
introduced when submitted upstream for a future U-Boot release. Users of
these boards should use the previous stable release of U-Boot until then.
Signed-off-by: E Shattow <e@freeshell.de>
The BeagleBone Green board is a revision of the BoneBlack board.
Having BeagleBone Black devicetree listed before BeagleBone Green will
select always the BeagleBone Black devicetree following the functioning of
board_fit_config_name_match().
Fix it by changing the test condition and selecting BoneBlack board only
if it is not a revision of this board.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Assorted fixes, refactorings and additions that are ready, and shave
off some load from upcoming series'.
Improves MMC performance on D1/T113 (missed clock divider), enables
eMMC access on the H616 family (never worked, many thanks to Jernej for
the fix!), DRAM detection fixes for the H616 (now reportedly stable).
Some patches for the upcoming Allwinner A133 SoC support: a few
refactorings, plus the DM clock and pinctrl driver. The DRAM init
routines work, but need some more polishing, that also holds back the
actual enablement patch, which will hopefully follow for v2025.07 still.
Also some preparatory patches for the Allwinner A523 SoC support, for
now just to improve the FEL save/restore code. There will be more patches
coming up for this, ideally also in the coming cycle still.
Gitlab CI passed, and I booted that briefly on some boards.
The AXP803 has been around for about a decade now, but so far we didn't
need SPL support, since the DRAM rail was wired up correctly at reset.
Now some boards using the A133 SoC use the (compatible) AXP707 with DDR4
memory, which requires the SPL to set the required 1.1V voltage manually.
Add the descriptions for the DC/DC regulators of the AXP803, and enable
that when CONFIG_AXP803_POWER is enabled.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There is a config option to run the PMIC at nominal voltages
which is not enabled on the i.MX8MP Beacon kit, so it the PMIC
runs at overdrive voltages. Unfortuately, the check for this
condition to set the GIC clock parent and rate is backwards from
what it should be, and accidentally sets the GIC clock to nominal
if the PMIC is in overdrive, and sets the GIC clock to overdrive
if the PMIC is in nominal. Fix this by inverting the logic on the
check.
Fixes: ab53bd43db ("arm64: imx: Add support for imx8mp-beacon-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
The configuration descriptions generated by binman contain the vendor
device-tree directory. Instead of adding it to all match strings just strip
it off.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The zkr ISA extension can be used to generate random numbers. Since RVA22
zkr is an optional ISA extension. It can be emulated by QEMU. Our RNG
driver detects if the extension is usable during driver binding. Let's
enable it by default on QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. In this case, the option
SPL_RISCV_MMODE is the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tianrui Wei <tianrui-wei@outlook.com>
In case ENV_IS_IN_SPI_FLASH is disabled, returning ENVL_SPI_FLASH
leads to failure to find environment driver on start up. Fix this
by testing whether ENV_IS_IN_SPI_FLASH is enabled and if not, then
return ENVL_NOWHERE instead.
Signed-off-by: Marek Vasut <marex@denx.de>
spl_perform_fixups is redundant in the current implementation. SPLs call
dram_init during spl_enable_cache in arch/arm/mach-k3/common.c. In
U-Boot, dram_init and dram_init_banksize are automatically called in
init_sequence_f. Therefore, SPLs and U-Boot always determine the correct
RAM size. During Linux boot, fdt_fixup_memory_banks adjusts the RAM size
in the Linux device tree, ensuring correct RAM usage.
dram_init() calls get_ram_size() for the Verdin AM62, which determines
the correct RAM size through read/write operations. However, due to the
K3 bootflow placing ATF in RAM and requiring cache coherence, calling
get_ram_size() with caches enabled prevents ATF boot. Removing this call
restores ATF boot functionality.
This fixes a regression introduced in commit 4164289db8 ("board:
verdin-am62: fix missing memory fixup call") which prevents some of our
Verdin AM62 modules from booting.
Fixes: 4164289db8 ("board: verdin-am62: fix missing memory fixup call")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. In this case we can easily fix this
by dropping the select line as the following choice statement handles
things correctly. We also drop the "default false" line as false / n is
the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Now that the UART driver can enable the required clocks, remove
the hard-coded clock enable.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that the UART driver can enable the required clocks, remove
the hard-coded clock enable.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that the UART driver can enable the required clocks, remove
the hard-coded clock enable. This requires a small re-order
of a couple functions.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Ouya microconsole is build on Nvidia Tegra 3 (T33) SoC, featuring a
quad-core 1.7 GHz ARM Cortex-A9 CPU and a ULP GeForce GPU, paired with 1GB
of DDR3 RAM and 8GB of internal flash storage. Running a modified Android
4.1 (Jelly Bean) OS with a custom launcher, it aimed for open-source gaming
via a digital storefront.
This implementation is mostly based on upstream Linux device tree and
fragments of work done by previous developers.
Co-developed-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Wadim Egorov <w.egorov@phytec.de> says:
This patch series syncs the phyCORE-AM62Ax feature-wise with our other
K3-based SoMs by adding SoM overlay handling and capsule updates. It
also introduces support for USBDFU boot and includes various minor fixes.
Link: https://lore.kernel.org/r/20250305045838.3614661-1-w.egorov@phytec.de
Add the phyCORE-AM62Ax to our common board directory to
enable our SOM detection for this product.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
TI's k3_dfu.env includes redundant dfu_alt_info_* data, some of which
is incompatible with our board configuration. Replace it with a custom
variant that better aligns with our setup, ensuring correct offsets and
eliminating unnecessary entries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
This config includes the phycore_am62ax_r5_defconfig file as well as
the am62x_r5_usbdfu.config fragment. We need another defconfig
because the AM62Ax has not enough internal SRAM to support all boot
sources. The normal phycore_am62ax_r5_defconfig should allow to boot
from MMC and OSPI while this new defconfig allows to boot from USB.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Provide a common part for our K3 based boards including general details
about environment handling and EFI capsule updates.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Basic board support for BeagleY-AI. Information on this
board can be found at https://beagleboard.org/beagley-ai
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrew Davis <afd@ti.com>
