DCC driver to support boot and runtime console scope
switch for dedicated boot and runtime consoles.
Change-Id: I7769dc44860a5fda99ca42ce17a3a6009288d7e7
Signed-off-by: Maheedhar Bollapalli <MaheedharSai.Bollapalli@amd.com>
GITS_CTLR.Quiescent is bit31, not bit1.
So fix GITS_CTLR_QUIESCENT_BIT to BIT32(31).
Change-Id: Ic16a52e0c4e557d68a8128ccc7e7a0f1a316a23b
Signed-off-by: Joe Yang <magicse7en@outlook.com>
The GICR_WAKER.Sleep and GICR_WAKE.Quiescent functionality is solely
about flushing out the LPI cache and ensuring that the contents are
consistent with external memory.
Hence, as shown in GIC-700 TRM version r3p0, software must poll for
Quiescent bit only if LPIs are supported.
Change-Id: I7d69b208428e24d8a3ff30e81bd1a8ee3d0bda6e
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Most newer CPU's have DSU and CPU power control core-off bit which
means before turning off CPUs from base power controller we need to
turn individual cores off from CPU Power control.
However there are certain older CPU's that don't have DSU and
don't support CPUPWRCTRL_EL1, so populate them as a list
and ignore setting core-off bit for those older CPU's as all newer
CPU's have them.
Note: unfortunately there is no mechanism to identify if a DSU is
present and CPUPWRCTRL_EL1 is supported through any CPU control
registers and CPUPWRCTRL_EL1 is supported only for ARM64 platforms
and not available in ARM32 platforms.
Change-Id: Iba6c3c8db60dbeb177cead7ebc65df8265860da7
Signed-off-by: Govindraj Raja <govindraj.raja@arm.com>
Enables the doorbell channels in MHUv3 for TC3.
Change-Id: Ib4f47df3e54f9182939ea6c1d8bc1a66a3c03094
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Adds driver support to preserve DSU PMU register values over a DSU
power cycle. This driver needs to be enabled by the platforms that
support DSU and also need it's PMU registers to be preserved
Change-Id: I7fc68a3d7d99ee369379aa5cd114fffc763fc0d2
Signed-off-by: Arvind Ram Prakash <arvind.ramprakash@arm.com>
Changes all occurrences of "RSS" and "rss" in the code and build files
to "RSE" and "rse".
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Change-Id: I9f72ad36ec233d7eaac3ce9e2f2b010130e1fa94
GIC600 erratum 2384374 is a Category B erratum. Part 1 is fixed
in this patch, and the Part 1 failure mode is described as
'If the packet to be sent is a SET packet, then a higher priority SET
may not be sent when it should be until an unblocking event occurs.'
This is handled by calling gicv3_apply_errata_wa_2384374() in the
ehf_deactivate_priority() path, so that when EHF restores the priority
to the original priority, the interrupt packet buffered
in the GIC can be sent.
gicv3_apply_errata_wa_2384374() is the workaround for
the Part 2 of erratum 2384374 which flush packets from the GIC buffer
and is being used in this patch.
SDEN can be found here:
https://developer.arm.com/documentation/sden892601/latest/
Signed-off-by: Arvind Ram Prakash <arvind.ramprakash@arm.com>
Change-Id: I4bb6dcf86c94125cbc574e0dc5119abe43e84731
Extend the SDS driver to be able to handle multiple
SDS regions:
- AP-SCP
- AP-RSS
Change-Id: Id303840b248c383b3f960227cbf6333d1cc75e65
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Signed-off-by: David Vincze <david.vincze@arm.com>
Reading the SCMI mailbox status in polling mode causes a burst of bus
accesses. On certain platforms, this would not be ideal as the shared
bus on the CPU subsystem might cause contentions across all the CPUs.
So allow platforms to specify a delay to be introduced while polling.
Change-Id: Ib90ad7b5954854071cfd543f4a27a178dde3d5c6
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
CryptoCell-712 and CryptoCell-713 drivers have been deprecated since
TF-A v2.9 and their removal was announced for TF-A v2.10 release.
See [1].
As the release is approaching, this patch deletes these drivers' code as
well as all references to them in the documentation and Arm platforms
code (Nuvoton platform is taken care in a subsequent patch). Associated
build options (ARM_CRYPTOCELL_INTEG and PLAT_CRYPTOCELL_BASE) have also
been removed and thus will have no effect if defined.
This is a breaking change for downstream platforms which use these
drivers.
[1] https://trustedfirmware-a.readthedocs.io/en/v2.9/about/release-information.html#removal-of-deprecated-drivers
Note that TF-A v3.0 release later got renumbered into v2.10.
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Change-Id: Idabbc9115f6732ac1a0e52b273d3380677a39813
Add unregistration function for the JTAG DCC (Debug Communication
Channel) console.
The unregistration function flushes DCC buffer before unregistering
the dcc console to make sure that no output char is pending.
Since console_flush() flushes chars for all registered consoles on
the platform, which is not required in this case, dcc_console_flush()
is being called instead.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Change-Id: I6f15a07c6ee947dc0e7aa8fb069227618080e611
The generic interrupt controller identifies an interrupt based on its
type whereas the GIC uses the notion of groups to identify an
interrupt.
Currently, they are used interchangeably in GICv3 driver. It did not
cause any functional issues since the matching type and group had the
same value for corresponding macros. This patch makes the necessary
fixes.
The generic interrupt controller APIs, such as
plat_ic_set_interrupt_type map interrupt type to interrupt group
supported by the GICv3 IP. Similarly, other generic interrupt
controller APIs map interrupt group to interrupt type as needed.
This patch also changes the name of the helper functions to use group
rather than type for handling interrupts.
Change-Id: Ie2d88a3260c71e4ab9c8baacde24cc21e551de3d
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
The generic interrupt controller identifies an interrupt based on its
type whereas the GIC uses the notion of groups to identify an
interrupt.
This patch changes the name of the helper functions to use group
rather than type for handling interrupts. No functional change in this
patch.
Change-Id: If13ec65cc6c87c2da73a3d54b033f02635ff924a
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Changes have been made in NPU firmware version 13 around error handling
which require some different register values to be set in AUXCTLR and
SYSCTRL1.
SiP service version number has been bumped up to 15 to reflect these
changes.
Change-Id: I6cda0048dc75df2150f7a0fe25f12ba6bf119ced
Signed-off-by: Rob Hughes <robert.hughes@arm.com>
This patch adds a helper API to explicitly refresh SBSA secure watchdog
timer. Please refer section A.3 of the following spec:
https://developer.arm.com/documentation/den0029/latest/
Change-Id: I2d0943792aea0092bee1e51d74b908348587e66b
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
When the Arm(R) Ethos(TM)-N NPU driver is built with TZMP1 support, the
NPU should use the firmware that has been loaded into the protected
memory by BL2. The Linux Kernel NPU driver in the non-secure world is
not allowed to configure the NPU to do this in a TZMP1 build so the SiP
service will now configure the NPU to boot with the firmware in the
protected memory.
BREAKING CHANGE: The Linux Kernel NPU driver can no longer directly
configure and boot the NPU in a TZMP1 build. The API version has
therefore been given a major version bump with this change.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65d00f54b3ade3665d7941e270da7a3dec02281a
The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the address extension and attribute control for the NPU's
streams. The non-secure world will still be allowed to read the address
extension for stream0 but non-secure access to all other streams have
been removed.
The API version has been given a minor bump with this change to indicate
the added functionality.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I2b041ca4a0a2b5cd6344a4ae144f75e137c72592
The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the NPU's event and aux control registers during the SMC
reset call. The aux control register will no longer be accessible by the
non-secure world.
The API version has been given a minor bump with this change to indicate
the added functionality.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I5b099e25978aa4089c384eb17c5060c5b4eaf373
When the Arm(R) Ethos(TM)-N NPU firmware is loaded by BL2 into protected
memory, the Linux kernel NPU driver cannot access the firmware. To still
allow the kernel driver to access some information about the firmware,
SMC calls have been added so it can check compatibility and get the
necessary information to map the firmware into the SMMU for the NPU.
The API version has been given a minor version bump with this change to
indicate the added functionality.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Idb076b7bcf54ed7e8eb39be80114dc1d1c45336d
The SiP service in the Arm(R) Ethos(TM)-N NPU driver requires that there
is at least one NPU available. If there is no NPU available, the driver
is either used incorrectly or the HW config is incorrect.
To ensure that the SiP service is not incorrectly used, a setup handler
has been added to the service that will validate that there is at least
one NPU available.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I8139a652f265cfc0db4a37464f39f1fb92868e10
To workaround Arm(R) Ethos(TM)-N NPU erratum 2838783, the NPU has been
configured to allow being woken up by both secure and non-secure events
to make sure that an event always wakes up the NPU.
The API version has been given a minor version bump with this change to
indicate that this fix is included.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I429cdd6bf1e633b4dedf2e94af28937dd892a0ba
Add Juno specific Makefile to the certificate tool build. That
Makefile is included by the certificate tool Makefile to add
information about the authentication data for the
Arm(R) Ethos(TM)-N NPU's firmware binary.
Signed-off-by: Mohamed Elzahhar <Mohamed.Elzahhar@arm.com>
Signed-off-by: Rob Hughes <robert.hughes@arm.com>
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Ie4b6a1c29d73b3ed5041b57f2cd88033be18a63a
Add platform specific Makefile to add UUIDs and command options
for the Arm(R) Ethos(TM)-N NPU firmware binary and certificate
data to the FIP so that the TF-A's BL2 can later be used to load
the Arm(R) Ethos(TM)-N NPU firmware binary into memory and verify
its integrity.
Add separate driver specific include header file for the
Arm(R) Ethos(TM)-N NPU images containing UUIDs and command options
to make it easy to port the FIP support to other platforms.
Signed-off-by: Daniele Castro <daniele.castro@arm.com>
Signed-off-by: Rob Hughes <robert.hughes@arm.com>
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I8cd64fb20d58f8bd539facb085606213d6cead05
The non-secure world delegation of the register needed to determine if
the Arm(R) Ethos(TM)-N NPU is active or sleeping will be removed in the
future. In preparation for the change, a new SMC call has been added to
allow the non-secure world to ask the SiP service for the state instead.
A minor API version bump has been done with this change to indicate
support for the new functionality.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I1338341be385cf1891f4809efb7083fae6d928bc
Adds a reset type argument for the soft and hard reset SMC calls to
indicate whether to perform a full reset and setup or only halt the
Arm(R) Ethos(TM)-N NPU. For use in cases where the NPU will not be
used but must be put into a known state, such as suspending the NPU
as part of power management.
Signed-off-by: Joshua Pimm <joshua.pimm@arm.com>
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I6018af85a28b0e977166ec29d26f04739123140c
The purpose of this patch is to address the T241 erratum T241-FABRIC-4,
which causes unexpected behavior in the GIC when multiple transactions
are received simultaneously from different sources. This hardware issue
impacts NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.
This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.
Erratum documentation:
https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf
The workaround is to ensure that MMIO accesses target the GIC on the
socket that holds the data, for example SPI ranges owned by the socket’s
GIC. This ensures that the GIC will not utilize the inter-socket AXI
Stream interface for servicing these GIC MMIO accesses.
This patch updates the functions that use the GICD_In{E} registers to
ensure that the accesses are directed to the chip that owns the SPI,
instead of using the global alias.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I04e33ba64eb306bd5fdabb56e63cbe273d8cd632
Change function prototype of plat_css_get_scmi_info() to fix the GCC
sign conversion error "comparison between signed and unsigned integer
expressions". Changing channel_id type to unsigned int since it can
never be a negative value.
Signed-off-by: Tony K Nadackal <tony.nadackal@arm.com>
Change-Id: I579b21497329db40897c10d86c8fc68e4877f3db
The Arm(R) Ethos(TM)-N NPU driver now supports configuring the SMMU
streams that the NPU shall use and will therefore no longer delegate
access to these registers to the non-secure world. In order for the
driver to support this, the device tree parsing has been updated to
support parsing the allocators used by the NPU and what SMMU stream that
is associated with each allocator.
To keep track of what NPU device each allocator is associated with, the
resulting config from the device tree parsing will now group the NPU
cores and allocators into their respective NPU device.
The SMC API has been changed to allow the caller to specify what
allocator the NPU shall be configured to use and the API version has
been bumped to indicate this change.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I6ac43819133138614e3f55a014e93466fe3d5277
The current comms protocol (where arguments and return data is embedded
into the MHU message) is now protocol v0. Protocol v1 embeds pointers
into the message, and has the RSS retrieve the data via DMA.
Change-Id: I08d7f09c4eaea673769fde9eee194447a99f1b78
Signed-off-by: Raef Coles <raef.coles@arm.com>
The GIC ICC_SGI0R_EL1 register's affinity fields are 8bit wide for GIC
v3 and v4. Fix the SGIR_AFF_MASK variable accordingly.
Change-Id: I09f3fdd006708b40162776620f82abcfc6c3f782
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
This patch adds two helper functions:
- plat_ic_raise_ns_sgi to raise a NS SGI
- plat_ic_raise_s_el1_sgi to raise a S-EL1 SGI
Signed-off-by: Florian Lugou <florian.lugou@provenrun.com>
Change-Id: I6f262dd1da1d77fec3f850eb74189e726b8e24da
If the interrupt being targeted is released from the CPU before the
CLEAR command is sent to the CPU then a subsequent SET command may not
be delivered in a finite time. To workaround this, issue an unblocking
event by toggling GICR_CTLR.DPG* bits after clearing the cpu group
enable (EnableGrp* bits of GIC CPU interface register)
This fix is implemented as per the errata 2384374-part 2 workaround
mentioned here:
https://developer.arm.com/documentation/sden892601/latest/
Change-Id: I13926ceeb7740fa4c05cc5b43170e7ce49598f70
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Created a function to abort all pending NS DMA transactions to
engage complete DMA protection. This call will be used by the
subsequent DRTM implementation changes.
Signed-off-by: Manish V Badarkhe <manish.badarkhe@arm.com>
Signed-off-by: Lucian Paul-Trifu <lucian.paultrifu@gmail.com>
Change-Id: I94992b54c570327d6746295073822a9c0ebdc85d
This commit adds a driver to conduct the AP's communication
with the Runtime Security Subsystem (RSS).
RSS is Arm's reference implementation for the CCA HES [1].
It can be considered as a secure enclave to which, for example,
certain services can be offloaded such as initial attestation.
RSS comms driver:
- Relies on MHU v2.x communication IP, using a generic MHU API,
- Exposes the psa_call(..) API to the upper layers.
[1] https://developer.arm.com/documentation/DEN0096/latest
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Signed-off-by: David Vincze <david.vincze@arm.com>
Change-Id: Ib174ac7d1858834006bbaf8aad0eb31e3a3ad107
The Arm Message Handling Unit (MHU) is a mailbox controller used to
communicate with other processing element(s). Adding a driver to
enable the communication:
- Adding generic MHU driver interface,
- Adding MHU_v2_x driver.
Driver supports:
- Discovering available MHU channels,
- Sending / receiving words over MHU channels,
- Signaling happens over a dedicated channel.
Signed-off-by: Tamas Ban <tamas.ban@arm.com>
Signed-off-by: David Vincze <david.vincze@arm.com>
Change-Id: I41a5b968f6b8319cdbdf7907d70bd8837839862e
This change performs a basic configuration of the SMMU root registers
interface on an RME enabled system. This permits enabling GPC checks
for transactions originated from a non-secure or secure device upstream
to an SMMU. It re-uses the boot time GPT base address and configuration
programmed on the PE.
The root register file offset is platform dependent and has to be
supplied on a model command line.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I4f889be6b7afc2afb4d1d147c5c1c3ea68f32e07
The following SMIDs are disabled by default.
* GICD: MBIST REQ error and GICD FMU ClkGate override
* PPI: MBIST REQ error and PPI FMU ClkGate override
* ITS: MBIST REQ error and ITS FMU ClkGate override
This patch explicitly enables them during the FMU init sequence.
Change-Id: I573e64786e3318d4cbcd07d0a1caf25f8e6e9200
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
This patch updates the gic600_fmu_init function to disable all safety
mechanisms for a block ID that is not present on the platform. All
safety mechanisms for GIC-600AE are enabled by default and should be
disabled for blocks that are not present on the platform to avoid
false positive RAS errors.
Change-Id: I52dc3bee9a8b49fd2e51d7ed851fdc803a48e6e3
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
The GIC-600AE uses a range of RAS features for all RAMs, which include
SECDED, ECC, and Scrub, software and bus error reporting. The GIC makes
all necessary information available to software through Armv8.2 RAS
architecture compliant register space.
This patch introduces support to probe the FMU_ERRGSR register to find
the right error record. Once the correct record is identified, the
"handler" function queries the FMU_ERR<m>STATUS register to further
identify the block ID, safety mechanism and the architecturally defined
primary error code. The description of the error is displayed on the
console to simplify debug.
Change-Id: I7e543664b74457afee2da250549f4c3d9beb1a03
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Older Qualcomm SoCs seem to have a custom Qualcomm implementation of
the GICv2 specification. It's mostly compliant but unfortunately it
looks like a mistake was made with the GICD_PIDR registers. PIDR2 is
defined to be at offset 0xFE8, but the Qualcomm implementation has it
at 0xFD8.
It looks like the entire PIDR0-3/4-7 block is swapped compared to the
ARM implementation: PIDR0 starts at 0xFD0 (instead of 0xFE0)
and PIDR4 starts at 0xFE0 (instead of 0xFD0).
Actually this only breaks a single assert in gicv2_main.c that checks
the GIC version: assert((gic_version == ARCH_REV_GICV2) ...
In release mode everything seems to work correctly.
To keep the code generic, allow affected platforms to override the
GICD_PIDR2_GICV2 register address in platform_def.h. Since this header
is typically included very early (e.g. from assert.h), add an #ifndef
so the definitions from platform_def.h takes priority.
Change-Id: I2929a8c1726f8d751bc28796567eb30b81eca2fe
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
When an Arm Ltd GIC (Arm GIC-[567]00) is instantiated with one or more
ITSes, the ITS MMIO frames appear between the distributor and
redistributor addresses. This makes the beginning of the redistributor
region dependent on the existence and number of ITSes.
To support various FPGA images, with and without ITSes, probe the
addresses in question, to learn whether they accommodate an ITS or a
redistributor. This can be safely done by looking at the PIDR[01]
registers, which contain an ID code for each region, documented in the
Arm GIC TRMs.
We try to find all ITSes instantiated, and skip either two or four 64K
frames, depending on GICv4.1 support. At some point we will find the
first redistributor; this address we then update in the DTB.
Change-Id: Iefb88c2afa989e044fe0b36b7020b56538c60b07
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The GIC specification describes ID registers in each GIC register frame
(PIDRx), which can be used to identify a GIC component. The Arm Ltd. GIC
implementations use certain ID values to identify the distributor, the
redistributors and other parts like ITSes.
Introduce a function that reads those part number IDs, which are spread
over two registers. The actual numbers are only meaningful in connection
with a certain GIC model, which would need to be checked beforehand, by
the caller.
Change-Id: Ia6ff326a1e8b12664e4637bc8e2683d2b5c7721c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, for the supported SCMI protocols, the version returned by the SCMI
platform agent must be exactly matching the driver's version (major version).
The recent change for the required version of Power Domain protocol means that
the platform must return version 2.0. This can be however a limitation in some
cases, where a SCMI-v1.0 platform can still be considered compatible with the
driver supported in firmware.
Relax the protocol version requirement such that any version older than the
one supported by the drivers can still be compatible.
Note: For now this has effect only on Power Domain protocol, as the other
drivers still require the "base" version 1.0.
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Change-Id: I310ae1869c2e952991a8d733f394029ab64087bf
