The RK3588-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3588.
It provides the following feature set:
* up to 16GB LPDDR4x
* on-module eMMC
* SD card (on a baseboard) via edge connector
* Gigabit Ethernet with on-module GbE PHY
* HDMI/eDP
* MIPI-DSI
* 4x MIPI-CSI (3x on FPC connectors, 1x over Q7)
* HDMI input over FPC connector
* CAN
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 host
* PCIe
- 1x PCIe 2.1 Gen3, 4 lanes
- 2xSATA / 2x PCIe 2.1 Gen1, 2 lanes
* on-module ATtiny816 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
* on-module Secure Element with Global Platform 2.2.1 compliant
JavaCard environment
The support is added for Tiger on Haikou devkit, similarly to RK3399
Puma and PX30 Ringneck.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ArmSoM Sige7 is a Rockchip RK3588 based SBC (Single Board Computer) by
ArmSoM.
There are two variants depending on the DRAM size : 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB memory LPDDR4x
Mali G610MC4 GPU
2x MIPI CSI 2 multiple lanes connector
64GB/128GB on board eMMC
uSD slot
1x USB 2.0 Type-A, 1x USB 3.0 Type-A, 1x USB 3.0 Type-C
1x HDMI 2.1 output
2x 2.5 Gbps Ethernet port
40-pin IO header including UART, SPI and I2C
USB PD over USB Type-C
Size: 92mm x 62mm
Kernel commit:
81c828a67c78 (arm64: dts: rockchip: Add ArmSom Sige7 board)
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the CoolPi 4 Model B and CoolPi CM5 EVB board to the documentation.
Fixes: 3e15dee38d ("board: rockchip: Add support for rk3588 based Cool Pi CM5 EVB")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566
SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64,
commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64
PineTab2").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-rock-pi-e with new defaults.
Remove the xPL_DRIVERS_MISC=y option, no misc driver is used in xPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_MDIO=y to ensure device tree props can be used by PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add myself as a reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-roc-cc with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands. Also add CMD_POWEROFF=y to be able to use the poweroff command.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y and PHY_REALTEK=y to support common
ethernet PHYs.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree file to MAINTAINERS and add myself as a
reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
Add documention for Rockchip rkmtd virtual block device.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.
Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.
Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.
There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR
Specifications:
CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
+ 4x Cortex-A55 (up to 1.8GHz)
GPU: Mali-G610 MP4
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
eMMC: 0GB/32GB/64GB/256GB HS400
MicroSD Slot: MicroSD SDR104
PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
supports M.2 WiFi and Bluetooth
4G Module: MiniPCIe x1, MicroSIM Card Slot x1
Audio Out: 3.5mm jack for stereo headphone output
Audio In: 2.0mm PH-2A connector for analog microphone input
Video Input: standard HDMI input port, up to 4Kp60
2x 4-lane MIPI-CSI, compatible with MIPI V1.2
Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
HDMI2.0, and HDMI1.4
2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
USB-A: USB 3.0, Type A
USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
8x PWMs, 2x I2Ss, 28x GPIOs
Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
Onboard IR receiver: 38KHz carrier frequency
RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
RTC IC HYM8563TS
5V Fan connector
Working Temperature: 0C to 70C
Power: 5.5*2.1mm DC Jack, 12VDC input
Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)
Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Update and improve documentation about build steps for SoCs that
require using TF-A and TPL binaries provided by Rockchip, such as
rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in
the list of supported boards. Minor page format improvements.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rename defconfig to include SoC name, use similar pattern as other
RK356x boards: <soc>-<name>.dts -> <name>-<soc>_defconfig
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update Rockchip documentation to include RK3566/RK3568 boards already
supported. Also list Pine64 boards under RK3566 and drop defconfig to
match other listed boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update documentation on how to write a bootable u-boot-rockchip-spi.bin
image into SPI flash. This removes the reference to a hardcoded and now
obsolete 0x60000 payload offset.
Also remove an obsolete reference to pad_cat.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the Rockchip rk3066a u-boot-tpl.bin file needs
to add the characters "RK30", while the other SoCs replace
the first 4 bytes. Bring this in line with the rest by
lowering CONFIG_TPL_TEXT_BASE and update rockchip.rst
instructions.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3588 evb1 v10 is a evalution board from Rockchip, it is a dev board for
rockchip and also a reference board for board vendors.
Hardware:
SoC: RK3588
DRAM: LPDDR4X 8GB
Debug: UART2 via USB
PCIe: 3x4 *1
SATA *2
HDMI out *2
HDMI IN *1
USB2.0 Host *2
USB3.0 Host *1
Type C *1
MIPI DSI panel
dts Sync from Linux v6.2.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the MAINTAINERS file to include the devicetree for the
rk3568-evb1-v10 board.
Also update Rockchip board docs to include information on building
RK3568 based devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to BootRom to load next stage, U-Boot SPL, into DRAM. BootRom then
jumps to U-Boot SPL to continue the normal boot flow.
However, there is no support to initialize DRAM on RK35xx SoCs using
U-Boot TPL and instead an external TPL binary must be used to generate a
bootable u-boot-rockchip.bin image.
Add CONFIG_ROCKCHIP_EXTERNAL_TPL to indicate that an external TPL should
be used. Build U-Boot with ROCKCHIP_TPL=/path/to/ddr.bin to generate a
bootable u-boot-rockchip.bin image for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add rk3066 Rikomagic MK808 to the list of
mainline supported Rockchip boards.
Include instructions for creating and programming
images to NAND and SD card.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
