The function cdns3_ep_config() calculates the maximum packet size based
on the Endpoint Type and the Gadget Speed and stores it in the variable
"max_packet_size". This value is then programmed in the USB Controller
for the corresponding Endpoint. This may result in a mismatch between
the maximum packet size programmed in the USB controller and the maximum
packet size seen by the UDC Core via "maxpacket" member of "struct usb_ep".
Additionally, since TD_SIZE is calculated in cdns3_ep_run_transfer() on the
basis of the maximum packet size stored in the "maxpacket" member of
"struct usb_ep", it may lead to an incorrect value of TD_SIZE when compared
with what the USB controller actually expects (max_packet_size).
Fix this.
Fixes: 7e91f6ccdc ("usb: Add Cadence USB3 host and gadget driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20241007121927.1680039-1-s-vadapalli@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
When DM_REGULATOR is disabled, all calls will return -ENOSYS. Account
for that so that targets like the IOT2050 will work again.
Fixes: de451d5d5b ("usb: dwc3-generic: support external vbus regulator")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Christian Marangi <ansuelsmth@gmail.com> says:
This series is a reworked version of the previous seried:
misc: introduce STATUS LED activity function
This series port and expand the legacy concept of LED boot from
the legacy Status LED API to new LED API.
One thing that many device need is a way to communicate to the
user that the device is actually doing something.
This is especially useful for recovery steps where an
user (for example) insert an USB drive, keep a button pressed
and the device autorecover.
There is currently no way to signal the user externally that
the bootloader is processing/recoverying aside from setting
a LED on.
A solid LED on is not enough and won't actually signal any
kind of progress.
Solution is the good old blinking LED but uboot doesn't
suggest (and support) interrupts and almost all the LED
are usually GPIO LED that doesn't support HW blink.
Additional Kconfg are also introduced to set the LED boot and
activity. Those are referenced by label.
A documentation for old and these new LED API is created.
Implement LED activity API similar to BOOT LED API.
Usual activity might be a file transfer with TFTP, a flash write...
User of this API will call led_activity_on/off/blink() to signal these
kind of activity.
New Kconfig is implemented similar to BOOT LED, LED_ACTIVITY to
enable support for it.
It's introduced a new /options/u-boot property "activity-led" and
"activity-led-period" to define the activity LED label and the
default period when the activity LED is set to blink mode.
If "activity-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement LED boot API to signal correct boot of the system.
led_boot_on/off/blink() are introduced to turn ON, OFF and BLINK the
designated boot LED.
New Kconfig is introduced, CONFIG_LED_BOOT to enable the feature.
This makes use of the /options/u-boot property "boot-led" to the
define the boot LED.
It's also introduced a new /options/u-boot property "boot-led-period"
to define the default period when the LED is set to blink mode.
If "boot-led-period" is not defined, the value of 250 (ms) is
used by default.
If CONFIG_LED_BLINK or CONFIG_LED_SW_BLINK is not enabled,
led_boot_blink call will fallback to simple LED ON.
To cache the data we repurpose the now unused led_uc_priv for storage of
global LED uclass info.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ofnode_options helpers to read options in /options/u-boot to
adapt to the new way to declare options as described in [1].
[1] dtschema/schemas/options/u-boot.yaml
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We currently init the LED OFF when SW blink is triggered when
on_state_change() is called. This can be problematic for very short
period as the ON/OFF blink might never trigger.
Toggle the LED (ON if OFF, OFF if ON) on initial SW blink to handle this
corner case and better display a LED blink from the user.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add newline character in log info end.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add PCA9452 PMIC/Regulator support.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The pmic could be trimed with updated BUCK1 range, so update the range
for trimed pmic. The default value of Toff_Deb is used to distinguish
the non-trimed and trimed pmic.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
S28HS02GT is dual-die package parts and do not support chip erase.
Fixes: 16dd109510 ("mtd: spi-nor-ids: Add Infineon(Cypress) s28hs02gt ID")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
S25HL02GT and S25HS02GT are dual-die package parts and do not support
chip erase.
Fixes: c95a914aed ("mtd: spi-nor-ids: Add Cypress s25hl-t/s25hs-t")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
The S25FS064S, S25FS128S, and S25FS256S are the same family of SPI NOR
Flash devices with S25FS512S. Some difference depending on the device
densities are taken care in post SFDP fixup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
The 6th ID byte is needed to distiguish S25FL-S and S25FS-S families.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The correct 4KB erase opcode should be selected based on the address width
currently used.
Fixes: 562d166a13 ("mtd: spi-nor-core: Add fixups for s25fs512s")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The mx25u25635f entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: f0084f1dfd ("drivers/mtd/spi/spi-nor-ids.c: add mx25u25635f support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The w25q16dw entry exists twice in spi_nor_ids, remove the less
complete variant of the entry and keep only one copy of it.
Fixes: baef13ec9d ("mtd: spi-nor-ids: Add support for flashes tested by xilinx")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Some Winbond SPI NORs have special SR3 register which is
used among other things to control whether non-standard
"Individual Block/Sector Write Protection" (WPS bit)
locking scheme is activated. This non-standard locking
scheme is not supported by either U-Boot or Linux SPI
NOR stack so make sure it is disabled, otherwise the
SPI NOR may appear locked for no obvious reason.
This SR3 WPS appears e.g. on W25Q16FW which has the same ID as
W25Q16DW, but the W25Q16DW does not implement the SR3 WPS bit.
Signed-off-by: Marek Vasut <marex@denx.de>
When trying to set the DCDC4 regulator, the code was accidentally
setting the voltage register for DCDC5 (VCC-DRAM). The higher voltage
doesn't harm the DRAM chips, but upsets the Linux regulator driver: when
it tried to correct that, it tripped over a separate DT bug.
The DCDC5 DT limits are 1.425 and 1.575V, which cannot bet set with the
rail's resolution of 50mV. The kernel driver gave up, and made in turn
the system hang, as the PMIC powers essential devices.
Fix the copy&paste bug by using the correct PMIC voltage register.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Clock gates and reset lines share a common structure in the sunxi clock
driver descriptions, but use different flags to tell them apart.
The description of the Allwinner A80 MMC clock reset lines was
erroneously using the "GATE" macro, which made the reset driver ignore
that entry, complaining with:
sunxi_set_reset: (RST-reset:#0) unhandled
Change that to the correct "RESET" macro, to make the reset driver
happy.
Fixes e0c7ce7e52 ("sunxi: clk: A80: add MMC clock support")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
John Watts <contact@jookia.org> says:
I'm doing some SPI work so I tried to compile all the drivers on my
sunxi board to try and avoid some regressions. This failed, so here are
some fixes for this.
Link: https://lore.kernel.org/r/20240427-spikconfig-v1-0-8a54772522f4@jookia.org
Signed-off-by: Tom Rini <trini@konsulko.com>
These dependencies are required for building the drivers and create
compile errors if not enabled.
Signed-off-by: John Watts <contact@jookia.org>
[trini: Add ARCH_MVEBU to KIRKWOOD_SPI]
Signed-off-by: Tom Rini <trini@konsulko.com>
Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> says:
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
Add support for parallel memories in zynq_qspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories in zynqmp_gqspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories and stacked memories configuration
in read_bar and write_bar functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories flash configuration in read status
register and read flag status register functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Initializing a clock driver to read a known static clock rate can take
some time at U-Boot proper pre-reloc phase.
Change to first try and read clock rate from DT to speed up boot time,
fall back to getting the clock rate from clock driver.
This help reduce boot time by around:
- ~35ms on a Radxa ROCK Pi 4 (RK3399)
- ~15ms on a Radxa ZERO 3W (RK3566)
Time that is wasted getting a static rate known at compile time.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mediatek pinctrl drivers call mtk_gpiochip_register() to bind the child
gpio controller as part of mtk_pinctrl_common_probe(). This breaks
gpiohog support because the gpio controller is bound too late for
DM_FLAG_PROBE_AFTER_BIND (set while binding hogs) to work.
Move the mtk_gpiochip_register() to mtk_pinctrl_common_bind() and call
this as the .bind method of each of the mediatek pinctrl drivers.
Signed-off-by: Chris Webb <chris@arachsys.com>
The SSCG is active with MDSEL[12] is not set. Previous commit
99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching
with MDSEL/PE caching") inverted the conditional assignment
of priv->sscg = !(cpg_mode & BIT(12)) during conversion from
(priv->sscg ? 16 : 0) to priv->cpg_mode & BIT(core->offset) ? 16 : 0;
Invert the assignment back to the correct state.
This fixes R8A77980, R8A77990, R8A77995 and R8A774C0.
Fixes: 99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching with MDSEL/PE caching")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These are a number of assorted upstream Linux fixes to the
BRCMNAND driver.
This patch set lowers the hamming distance between the Linux
and U-Boot drivers a bit as well, while we deviate quite
a bit it is still possible to bring fixes over thanks to
exercises like this.
The patches pass the pipeline CI:
https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/22535
Backport from the upstream Linux kernel
commit c2cf7e25eb2a3c915a420fb8ceed8912add7f36c
"mtd: rawnand: brcmnand: Add support for getting ecc setting from strap"
Note: the upstream kernel introduces a new
bool brcmnand_get_sector_size_1k() function because the int
version in U-Boot has been removed in Linux. I kept the old
int-returning version that is already in U-Boot as we depend
on that in other code.
BCMBCA broadband SoC based board design does not specify ecc setting in
dts but rather use the SoC NAND strap info to obtain the ecc strength
and spare area size setting. Add brcm,nand-ecc-use-strap dts propety for
this purpose and update driver to support this option. However these two
options can not be used at the same time.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240301173308.226004-1-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Tested-by: William Zhang <william.zhang@broadcom.com>
Backport of upstream Linux
commit 8e7daa85641c9559c113f6b217bdc923397de77c
"mtd: rawnand: brcmnand: Support write protection setting from dts"
Augmented to also support the "write-protect" boolean property.
The write protection feature is controlled by the module parameter wp_on
with default set to enabled. But not all the board use this feature
especially in BCMBCA broadband board. And module parameter is not
sufficient as different board can have different option. Add a device
tree property and allow this feature to be configured through the board
dts on per board basis.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-14-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
This is a port of the read data bus interface from the Linux
brcmnand driver, commit 546e425991205f59281e160a0d0daed47b7ca9b3
"mtd: rawnand: brcmnand: Add BCMBCA read data bus interface"
This is needed for the BCMBCA RAW NAND driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Backport from upstream Linux
commit 60177390fa061c62d156f4a546e3efd90df3c183
"mtd: rawnand: brcmnand: Fix mtd oobsize"
brcmnand controller can only access the flash spare area up to certain
bytes based on the ECC level. It can be less than the actual flash spare
area size. For example, for many NAND chip supporting ECC BCH-8, it has
226 bytes spare area. But controller can only uses 218 bytes. So brcmand
driver overrides the mtd oobsize with the controller's accessible spare
area size. When the nand base driver utilizes the nand_device object, it
resets the oobsize back to the actual flash spare aprea size from
nand_memory_organization structure and controller may not able to access
all the oob area as mtd advises.
This change fixes the issue by overriding the oobsize in the
nand_memory_organization structure to the controller's accessible spare
area size.
Fixes: a7ab085d7c16 ("mtd: rawnand: Initialize the nand_device object")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-6-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Backport of upstream Linux
commit 5d53244186c9ac58cb88d76a0958ca55b83a15cd
"mtd: rawnand: brcmnand: Fix potential out-of-bounds access in oob write"
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-5-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Backport from the Linux kernel:
commit 9cc0a598b944816f2968baf2631757f22721b996
"mtd: rawnand: brcmnand: Fix potential false time out warning"
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-3-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Backport from the Linux kernel
commit 2ec2839a9062db8a592525a3fdabd42dcd9a3a9b
"mtd: rawnand: brcmnand: Fix ECC level field setting for v7.2 controller"
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-2-william.zhang@broadcom.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/22526
- Add DA9063 watchdog support for the imx6q-lxr2 board.
- Add support for DH electronics i.MX8M Plus DHCOM PicoITX
- Add DH i.MX8MP DHCOM SoM on DRC02 carrier board
- Several fsl_esdhc_imx improvements.
- Pas no-mmc-hs400 to mmc2 on imx8mm-cl-iot-gate.
