These helpers wrongly return the updated register value. As a non-zero
value indicates failure, this causes various clock operations are
considered failed.
Correct the return value to constant zero, since these simple MMIO
operations won't fail. This fixes clock enabling failures during booting
process,
In: serial@4140000
Out: serial@4140000
Err: serial@4140000
Net: Enable clock-controller@3002000 failed
failed to enable clock 0
No ethernet found.
which leads to misoperation of various peripherals.
Fixes: 5f364e072e ("clk: sophgo: cv1800b: Add clock controller driver for cv1800b SoC")
Tested-by: Yuguo Pei <purofle@gmail.com>
Signed-off-by: Yao Zi <ziyao@disroot.org>
The UUU tool excepts the interrupt-in endpoint to be ep1in, otherwise
it crashes. This is a result of the previous hard-coded EP setup in
drivers/usb/gadget/epautoconf.c which did special-case EP allocation
for SPL builds, and which was since converted to this callback, but
without the special-case EP allocation in SPL part.
This reinstates the SPL part in an isolated manner, only for NXP iMX
SoCs, only for SPL builds, and only for the ep1in interrupt-in endpoint.
Fixes: 1918b8010c ("usb: dwc3: gadget: Convert epautoconf workaround to match_ep callback")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250319220805.219001-1-marex@denx.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Make struct renesas_dbsc5_board_config {} definition public via
include/dbsc5.h, so this structure can be defined in board files
and passed into the DBSC5 DRAM driver by overriding weak function
dbsc5_get_board_data() on board level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add auto-detection and handling of Renesas R-Car V4H-3 and V4H-5
in addition to V4H-7 SoC variants based on OTP fuse programming.
The V4H-3 and V4H-5 variants have reduced DRAM frequency options.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Update the DRAM initialization code to match DBSC5 initialization code
rev.1.10 , which is currently the latest version available. This makes
DRAM initialization operational on Renesas R-Car V4H R8A779G0 rev.3.0.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reinstate missing increment by two in DBTR11 calculation based
on the original DBSC5 initialization code rev.0.80. The original
code did ... ODTLon - (js2[JS2_tODTon_min] - 1) + 1 , which was
incorrectly converted into ODTLon - js2[JS2_tODTon_min], but
should have been converted to ODTLon - js2[JS2_tODTon_min] + 2.
Add the missing +2 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The JS1 index is calculated correctly, but the limiter cannot
be the max() function because the index should be lower than
JS1_USABLEC_SPEC_HI and the max() function would unconditionally
override the JS1 index to JS1_USABLEC_SPEC_HI. Use clamp() to
limit the JS1 index instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix copy paste error in MD pin handling for 5500 Mbps and 4800 Mbps case,
each should be handled by MD[19,17] == 2 and MD[19,17] == 3 respectively.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Zynq:
- Guard code around SPL_FS_LOAD_PAYLOAD_NAME
Versal*:
- Remove tftp block size 4096
Versal:
- Use clocks per DT binding
- Store driver data in data section
Versal Gen 2:
- Fix major/minor version decoding
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZ8g41AAKCRDKSWXLKUoM
IWoUAJwLRR8n8sSD8/CFMVRpRtKeWiHhKACghZ6WQjRBGTW8kX0Kyvrz14z/7Lw=
=dzMG
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2025.04-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx changes for v2025.04-rc4
Zynq:
- Guard code around SPL_FS_LOAD_PAYLOAD_NAME
Versal*:
- Remove tftp block size 4096
Versal:
- Use clocks per DT binding
- Store driver data in data section
Versal Gen 2:
- Fix major/minor version decoding
Currently, Kconfig allows building CONFIG_DM_74X164 without
CONFIG_DM_SPI, which results in linker errors because this driver
actually uses dm_spi_* functions:
drivers/gpio/74x164_gpio.o: in function `gen_74x164_write_conf':
undefined reference to `dm_spi_claim_bus'
undefined reference to `dm_spi_xfer'
undefined reference to `dm_spi_release_bus'
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Unfortunately this change was not safe as some devices are bound before
relocation, but we don't want to probe them.
It causes 'raise: Signal # 8 caught' on jerry.
Move the bootstage timer to after autoprobe in initf_dm() since the
trace test does not tolerate any variance.
This reverts commit 21dd873572.
Signed-off-by: Simon Glass <sjg@chromium.org>
Line 171 in README is describing that before relocation
no code should use global variable because global variables
are placed to BSS section which is initialized to 0 after
relocation.
On Versal platforms clock driver is initialized before
relocation (via using dm,bootph-all flag in DT) and global
variables are initialized which works if this is used only
before relocation. But the variables are used after
relocation too but values are zeroed which is ending up
incorrect behavior.
That's why place variables to data section to ensure that
values are not cleared which is for now the quickest
temporary solution. The correct way to do it is to move
all global variables to private data to avoid it.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250218052419.1141139-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per the bindings the reference clocks naming has changed
from "pl_alt_ref_clk" to "pl_alt_ref" and "ref_clk" to "ref".
Update the same in the clock driver. Also add the fallback option
for older DT bindings.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250206091533.1447234-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When an error is detected in the TSEC receive path, the driver currently
prints an error message, but leaves the corresponding packet descriptor
in its old state (i.e. owned by the CPU side). As a result, the packet
queue can be starved of available buffers if enough errors happen.
To recover from errors, re-arm the packet buffer descriptor after an
error has been detected.
Errors can be provoked by changing a PHY with phy-mode = "rgmii-id" to
phy-mode = "rgmii".
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is necessary for the following patch. No functional change.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
These two files were using IS_ENABLED() to test for CONFIG flags but omitted
the CONFIG_ prefix and so did not work as expected.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pin count wasn't updated when the special pins were added, as a
result it was never possible to configure the special pins on SM8250
boards.
Fix the pin count and allow the special pins to be configured. This
fixes sdcard support on the RB5.
Fixes: 58fa520424 ("pinctr: qcom: sm8250: add special pins pins configuration data")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add the other LDOs that our rpmh driver can currently support. Some of
these are used on the RB5 to power the sdcard.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add support for sm8150 clock controller to clk stub driver.
Signed-off-by: Julius Lehmann <lehmanju@devpi.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Add a stub clock driver which can be used to bind clock controllers
which aren't required for the platform to boot, but which are needed for
U-Boot drivers to work.
In addition, add a NOP parent driver to allow for binding the parent
nodes of the clock.
Initially this driver supports a Qualcomm platform where the MMC driver
tries to fetch the RPM clock controller, which is not actually required
for the device to work.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
For eMMC v4 and newer that is smaller than 2 GiB, the JEDEC JESD84-B51
section 6.2.4 Configure partitions indicates that EXT_CSD SEC_COUNT
should not be used to determine device size, and instead device size
should be calculated from C_SIZE and C_SIZE_MULT.
This is not exactly accurate, the 2 GiB limit is not a hard line,
there are eMMC devices which are smaller than 2 GiB and still
require device size to be determined from EXT_CSD SEC_COUNT. The
hard line is instead OCR HCS bit, which indicates whether the device
is byte or sector addressed, the former applies to most devices
below 2 GiB, and the later applies mostly to devices above 2 GiB.
However, there are a couple of devices which are smaller than 2 GiB
and still set the OCR HCS bit to indicate they are sector addressed,
and therefore the size calculation for those devices should also
use EXT_CSD SEC_COUNT . Use mmc->high_capacity flag to discern the
devices instead of arbitrary 2 GiB limit. The mmc->high_capacity flag
reflects the OCR HCS bit state.
Fixes: 639b7827d1 ("mmc: fix the condition for MMC version 4")
Signed-off-by: Marek Vasut <marex@denx.de>
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged. Add missing GPIO3-B1 to GPIO3-B7
pinmux data to rk3328_mux_recalced_data as mux register offset for these
pins does not follow rockchip convention.
This matches changes in following Linux commits:
- e8448a6c817c ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
- 5ef6914e0bf5 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins")
- 128f71fe014f ("pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
The struct contains an iomem pointer that we later remap and update.
Remove const from the struct definition.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Pin detection on t20 depends on node name. With recent changes
in node naming, let's remove '_' to be safe about both '_' or
'-' use.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Bind SYSRESET child to parent node since it does not have
its own node in the device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Bind GPIO and SYSRESET children to parent node since they
do not have their own nodes in the device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Requesting of PMIC's GPIO child should be done by binding
GPIO driver to PMIC's node is GPIO driver does not have
its own node.
This reverts commit c03cd98d1a.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
u-boot-dfu-20250211:
CI:
- https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/24556
Android:
- Handle boot images with missing DTB
Usb gadget:
- Fix nullptr in g_dnl when serial# is unset
- Add missing schedule() in f_mass_storage gadget
- Add support for STih407 in dwc3-generic
- Fix usb clocks on STih407
- Migrate STih407 to DM_USB_GADGET
Add STi glue logic to manage the DWC3 HC on STiH407
SoC family. It configures the internal glue logic and
syscfg registers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250130163547.512990-6-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
STi will migrate to dwc3-generic driver, dwc3-sti-glue driver
can be removed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20250130163547.512990-4-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
In case "ums" command is used on platforms which don't implement
g_dnl_board_usb_cable_connected() and USB cable is not connected,
we stay inside sleep_thread() forever and watchdog is triggered.
Add schedule() call to avoid this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20241202074644.5380-1-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
emul_rtc_probe() is not called from anywhere else that's why make it
static. Issue is reported by build with W=1.
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch add support to read register base address by name if
provided.
Also devfdt_get_addr_* is changed to dev_read_addr_* to support DT
live tree.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The reg-names in mt7988.dtsi have no _base suffix. Remove the suffix
will also make it match upstream linux format.
Fixes: 8c2cb748ef (pinctrl: mediatek: mt7988: rename reg-names to upstream linux format)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Heiko Schocher <hs@denx.de> says:
In linux we have the option to create the name of a led
optionally through the following properties:
- function
- color
- function-enumerator
This series adds support for parsing this properties if there
is no label property.
Link: https://lore.kernel.org/r/20250128135246.74838-1-hs@denx.de
[trini: Document name parameter in led.h]
in linux we have the option to create the name of a led
optionally through the following properties:
- function
- color
- function-enumerator
This patch adds support for parsing this properties if there
is no label property.
The led name is created in led_post_bind() and we need some
storage place for it. Currently this patch prevents to use
malloc() instead it stores the name in new member :
char name[LED_MAX_NAME_SIZE];
of struct led_uc_plat. While at it append led tests for the
new feature.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current behaviour of this function will dereference a null pointer
if the serial# environment variable is unset. This was discovered on a
board where U-Boot did not have access to the first 256MB of ram,
resulting in a board crash.
In the event that U-Boot has full access to memory, it will still read
from address 0, which is probably not optimal.
This simple check is enough to fix it
Signed-off-by: Michael Ferolito <michaelsunn101@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20250128030945.1219589-1-michaelsunn101@gmail.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Fixes annoying warnings of the following type when built with W=1 (for
each file including fpga.h):
CC drivers/fpga/fpga.o
In file included from /mnt/data/adahl/src/u-boot/include/xilinx.h:7,
from /mnt/data/adahl/src/u-boot/drivers/fpga/fpga.c:10:
/mnt/data/adahl/src/u-boot/include/fpga.h:61:1: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
61 | const fpga_desc *const fpga_get_desc(int devnum);
| ^~~~~
/mnt/data/adahl/src/u-boot/include/fpga.h:81:1: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
81 | const fpga_desc *const fpga_validate(int devnum, const void *buf,
| ^~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/fpga.c:36:1: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
36 | const fpga_desc *const fpga_get_desc(int devnum)
| ^~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/fpga.c:53:1: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
53 | const fpga_desc *const fpga_validate(int devnum, const void *buf,
| ^~~~~
Do some type and cast cleanup on that fpga_desc type while at it.
Link: https://gcc.gnu.org/onlinedocs/gcc/Warning-Options.html#index-Wignored-qualifiers
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20250121162213.1477506-1-ada@thorsis.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If the least significant bit of the address is set to one when
using the DDR protocol for data transfer then the results are
indeterminate for few flash devices. To fix this the least
significant bit of the address is set to zero.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250106095120.800753-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
