When bcmgenet complete to write Rx buffer with the DMA,
some U-Boot commands write data to the buffer directly.
Those write data will become dirty in CPU cache.
After this driver calls free_pkt to the buffer,
the buffer is assigned as the future Rx buffer.
At some point, if bcmgenet writes to a buffer with DMA
and CPU cache flushes dirty data to the buffer,
the buffer is corrupted.
This patch calls flush_dcache_range in free_pkt
to immediately flush the data written by U-Boot command
and prevent data corruption.
This issue can be reproduced using wget on Raspberry Pi4.
If wget receives data larger than
RX_BUF_LENGTH * RX_DESCS = 2048 * 256 bytes,
it will timeout due to data corruption.
In addition, if LOG_DEBUG is enabled in net/tcp.c,
the following error log is output.
TCP RX TCP xSum Error
Signed-off-by: Yasuharu Shibata <yasuharu.shibata@gmail.com>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Let users configure default auto-negotiation timeout via Kconfig
instead of specifying it in board configuration headers. This is
the first step toward converting this to Kconfig fully, so far the
legacy PHY_ANEG_TIMEOUT in configuration headers takes precedence.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
The eth-uclass state machine doesn't prevent imbalanced start()/stop()
calls - to the contrary, it even provides eth_init_state_only() and
eth_halt_state_only() functions that change the state without any calls
into the driver. This means that the driver must be robust against
duplicate start() and stop() calls as well as send/recv calls while the
interface is down.
We decide not to print error messages but just to return an error in the
latter case, as trying to send packets on a disabled interface commonly
happens when the netconsole is still active after the Ethernet has been
halted during bootm.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This driver support the Synopsys Designware Ethernet 10G
IP block refer from the driver dwc_eth_qos.
The driver MAC register mapping is different between
Synopsys QoS IP and Synopsys 10G IP, and thus new file
is created meant for Sysnopsys 10G IP.
The dwc_eth_xgmac_socfpga.c is specific to a device family,
the driver support the specific configuration used in
Intel SoC FPGA Agilex5.
This driver is extensible for other device family to use.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Initialize register in cv1800b ethernet phy to make it compatible with
generic phy driver
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move cru_rk3308.h and grf_rk3308.h to arch-rockchip to match path used
for all other Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync device tree from linux v6.8 and rename the rockchip,rk3308-mac
compatible in gmac_rockchip driver to match upstream linux.
Also move rk3308-roc-cc gmac node to u-boot.dtsi to not break features
not enabled in upstream device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
-----BEGIN PGP SIGNATURE-----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=up9Y
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20240419' of https://source.denx.de/u-boot/custodians/u-boot-stm
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Use const bool for the values parsed out of DT. Drop the duplicate
assignment of false into those bool variables, assign them directly
with the content parsed out of DT. Abbreviate the variable name too.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use dev_*() only to print all the logs from this glue code,
instead of mixing dev_*(), log_*(), pr_*() all in one code.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the log_debug() calls on top of the bit manipulation code.
No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use FIELD_PREP to configure content of ETH_SEL bitfield in SYSCFG_PMCSETR
register. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Replace ifdef CONFIG_CLK with if (CONFIG_IS_ENABLED(CLK)) to improve code
build coverage. Some of the functions printed debug("%s: OK\n", __func__);
on exit with and without CLK enabled, some did not, make it consistent and
print nothing if CLK is disabled.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move board_interface_eth_init() into eqos_probe_syscfg_stm32() in STM32
driver glue code. The eqos_probe_syscfg_stm32() parses STM32 specific DT
properties of this MAC and configures SYSCFG registers accordingly, there
is nothing board specific happening in this function, move it into generic
driver code instead. Drop the now unused duplicates from board files.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The current glue code is specific to STM32MP15xx, the upcoming STM32MP13xx
will introduce another entry specific to the STM32MP13xx. Rename the current
entry to eqos_stm32mp15_config in preparation for STM32MP13xx addition. No
functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move STM32 glue code into separate file to contain the STM32 specific
code outside of the DWMAC core code. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER<christophe.roullier@foss.st.com>
Allowing multicast packets is required for IPv6 neighbor discovery
protocol.
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
In IPv6 context, the ICMP and UDP checksum byte in the RX packet
is initially set to 0, recaclculated, and then re-inserted.
This process can result in a dirty cache line. To prevent issues,
it is essential to invalidate cache for the RX buffer before freeing
the descriptor for next DMA transfer.
This ensure that the dirty cache line doesn't inadvertently written back
due to cache eviction, there by corrupting the RX buffer
Signed-off-by: Parvathi Bhogaraju <pbhogaraju@microsoft.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
MD Danish Anwar <danishanwar@ti.com> says:
Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
AM654 SR2.0.
The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
support for ICSSG driver in uboot.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
cores and RPROC cores need to be booted with the firmware. This step is
done inside driver similar to kernel.
The remoteproc driver uses request_fw_into_buf() API from fs-loader driver
to load and start rproc with the required firmwares.
This series only introduces driver files. The device tree and config
changes to enable ICSSG driver will be introduced later.
ICSSG firmware supports FDB commands. Add support to send FDB commands
from driver. Once rx_flow_id is obtained from dma, let firmware know that
we are using this rx_flow_id by sending a FDB command.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with
the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports
two slices per instance. This driver caters to both slices / ports of
the icssg subsystem.
Since it is not possible for Ethernet driver to register more than one
port for a given instance, this patch introduces top level PRUETH as
UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support
bringing up more than one Ethernet interface in U-Boot.
Since top level driver is UCLASS_MISC, board files would need to
instantiate the driver explicitly.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. Add MII helper APIs and
MACROs. These APIs and MACROs will be later used by ICSSG Ethernet driver.
Also introduce icssg_prueth.h which has definition of prueth related
structures.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
The device name is a concatenation of the device node name of the cpsw
device and of the device node name of the port. In my case that is
ethernet@8000000
port@1
First the buffer is really too small, but more importantly, there is no
boundary check. Use snprintf() and increase the buffer size.
Fixes: 38922b1f4a ("net: ti: am65-cpsw: Add support for multi port independent MAC mode")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Missing line-feeds in error messages lead to output like:
phy_startup() failed: -110FAILED: -110=>
Output like the following is much easier to read:
phy_startup() failed: -110
FAILED: -110
=>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Change to regulator_set_enable_if_allowed to avoid enable failure,
in case same phy supply shared by multiple FEC controllers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Pull the PHY GPIO reset code into separate function, since
this is and will be reused multiple times. Set up default
reset assert and deassert timing to generous 20ms and 1ms
for maximum compatibility in case those DT properties are
missing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
From the ethernet header is not on aligned, because the length
of the ethernet header is 14 bytes.
Therefore, unaligned access must be done here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
There is no need to perform the endian twice here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
shrink the first argument of log_msg_ret(), add dev_xxx() functions for
error reporting.
Fixes: 9d8f78a2a7 ("net: add hifemac Ethernet driver for HiSilicon platform")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
The initial commit used log_msg_ret() wrongly. Fix that by moving error
report to a separate dev_err() call and shrink the first argument of
log_msg_ret() to no more than 4 chars.
Fixes: 6b5c8d98e2 ("net: add hifemac_mdio MDIO bus driver for HiSilicon platform")
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
As with fixed-link phy device, the NC-SI phy devive does not
require an mdio bus. So, a condition is added to check the
NC-SI phy id to avoid accessing the bus pointer that is NULL.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Booting R-Car Gen3 arm64 U-Boot with CONFIG_UBSAN=y resulted in:
=====================================================================
UBSAN: Undefined behaviour in drivers/net/phy/phy.c:728:19
left shift of 1 by 31 places cannot be represented in type 'int'
=====================================================================
Fix it by appending the UL suffix to the numeric literal. While at it,
convert the type of "addr" variable from signed to unsigned, to protect
against shifting the numeric literal by a negative value (which would
lead to yet another undefined behavior).
Fixes: 1adb406b01 ("phy: add phy_find_by_mask/phy_connect_dev")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
* Using U-suffix for integer is sufficient.
* ffs() of non-zero value cannot be 0. But addr being unsigned is
* preferable.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Configure LEDs on BCM54210E so they would blink on activity
and indicate link speed. Without this the LEDs are always on
if cable is plugged in.
Signed-off-by: Marek Vasut <marex@denx.de>
The issue occurs the UAF (use-after-free) to cause double free
when do the realloc function for the pointers during the
reinitialization NC-SI process, and it will cause the memory
management occurs error.
So, nullify these pointers after free.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
