Add configuration for the SC7280, copied from Linux 6.11
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now the Qualcomm controller and PHY drivers were accepted,
enable then in the qcom_defconfig file.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The upstream version has new defines use to build DT, drop
it in favor of the dts/upstream more recent one.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The ufsphy_v2_regs_layout is not used, drop it and fix:
phy-qcom-qmp-ufs.c:87:27: warning: ‘ufsphy_v2_regs_layout’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The qcom_pmic code is broken for new PMICs and should be fixed,
without the QUIRK the code is broken and the GPIOs don't work
anymore on SM8550 and SM8650 platforms.
Partially revert the revert and only add the quirk on the PM8550
PMIC, making the buttons and MMC detect gpio work again.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
On earlier platforms, the vqmmc regulator was enabled by the
previous bootloader, but on the newest (SM8650) it's not
and we need vqmmc to be enabled in order to have the card
to respond.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Set LOG_CATEGORY and pr_fmt. Also fix the time.h include.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Fastboot is very hungry when it flashes larges chunks, and 8MiB
is way too small, allocate a much bigger size like other platforms
using Fastboot.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # rb1
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
The SM8550 and SM8650 SoCs requires PINCONF to properly
setup SDC pins in order to function correctly.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Simon Glass <sjg@chromium.org> says:
Labgrid provides access to a hardware lab in an automated way. It is
possible to boot U-Boot on boards in the lab without physically touching
them. It relies on relays, USB UARTs and SD muxes, among other things.
By way of background, about 4 years ago I wrong a thing called Labman[1]
which allowed my lab of about 30 devices to be operated remotely, using
tbot for the console and build integration. While it worked OK and I
used it for many bisects, I didn't take it any further.
It turns out that there was already an existing program, called Labgrid,
which I did not know about at time (thank you Tom for telling me). It is
more rounded than Labman and has a number of advantages:
- does not need udev rules, mostly
- has several existing users who rely on it
- supports multiple machines exporting their devices
It lacks a 'lab check' feature and a few other things, but these can be
remedied.
On and off over the past several weeks I have been experimenting with
Labgrid. I have managed to create an initial U-Boot integration (this
series) by adding various features to Labgrid[2] and the U-Boot test
hooks.
I hope that this might inspire others to set up boards and run tests
automatically, rather than relying on infrequent, manual test. Perhaps
it may even be possible to have a number of labs available.
Included in the integration are a number of simple scripts which make it
easy to connect to boards and run tests:
ub-int <target>
Build and boot on a target, starting an interactive session
ub-cli <target>
Build and boot on a target, ensure U-Boot starts and provide an interactive
session from there
ub-smoke <target>
Smoke test U-Boot to check that it boots to a prompt on a target
ub-bisect <target>
Bisect a git tree to locate a failure on a particular target
ub-pyt <target> <testspec>
Run U-Boot pytests on a target
Some of these help to provide the same tbot[4] workflow which I have
relied on for several years, albeit much simpler versions.
The goal here is to create some sort of script which can collect
patches from the mailing list, apply them and test them on a selection
of boards. I suspect that script already exists, so please let me know
what you suggest.
I hope you find this interesting and take a look!
[1] https://github.com/sjg20/u-boot/tree/lab6a
[2] https://github.com/labgrid-project/labgrid/pull/1411
[3] https://github.com/sjg20/uboot-test-hooks/tree/labgrid
[4] https://tbot.tools/index.html
Link: https://lore.kernel.org/r/20241112141326.643128-1-sjg@chromium.org
[trini: Move the sjg-lab job to prior to world build, to fix pipeline
status]
Signed-off-by: Tom Rini <trini@konsulko.com>
Sometimes this breaks, so add a build to keep it working. Since sandbox
enables a lot of options, it is a good board to use. The new config is
created simply by copying the existing sandbox and turning off CMDLINE
Once we have tests for non-CMDLINE operation, this can be adjusted to
run those tests.
Create a new build which will be picked up by CI. Update the maintainer
entry as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a way to run tests on a real hardware lab. This is in the very early
experimental stages. There are only 23 boards and 3 of those are broken!
(bob, ff3399, samus). A fourth fails due to problems with the TPM tests.
To try this, assuming you have gitlab access, set SJG_LAB=1, e.g.:
git push -o ci.variable="SJG_LAB=1" dm HEAD:try
This relies on the two previous series targeted at -next as well as the
bugfix series for -master
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Use an 'r' string to avoid a warning:
test/py/tests/test_spi.py:698: DeprecationWarning: invalid escape
sequence '\s'
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Beagleplay board uses an SoC from the TI K3 family. This has both a
Cortex-R core and a Cortex-A core and the R core needs to come up before
the A core. In both cases we have U-Boot SPL then U-Boot proper being
used.
In practice this means we need two entirely separate builds to produce
an image.
Handle this in test.py by adding more parameters.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can take a while and involve multiple steps (e.g. turning the board
back off). Add a section for it and show the output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Send the Labgrid quit characters to ask it to exit gracefully. This
typically allows it to power off the board being used. Only do this when
labgrid is being used (detected with an env var).
If that doesn't work, try the less graceful approach.
The normal approach for pytest is to simply kill the child process. This
makes Labgrid exit immediately. Thus it does not get a chance to execute
the 'off' part of strategy (which may power it off) and release the
device.
Without this, every board disconnect leaves the board in a bad state,
requiring separate steps to recover the board, then power it off.
The action is conditional on since USE_LABGRID_SJG being set, so only
affects operation if the Labgrid-sjg integration is being used.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a very annoying bug at present where the terminal echos part
of the first command sent to the board. This happens because the
terminal is still set to echo for a period until Labgrid starts up and
can change this.
Fix this by disabling echo (and other terminal features) as soon as the
spawn happens.
Signed-off-by: Simon Glass <sjg@chromium.org>
We expect commands to be echoed and this should happen quite quickly,
since U-Boot is sitting at the prompt waiting for a command.
Reduce the timeout for this situation. Try to produce a more useful
error message when something goes wrong. Also handle the case where the
connection has gone away since the last command was issued.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is quite a bit of code in pytest to try to start up U-Boot on a
board, with timeouts, expects, etc.
This is tedious to maintain and is peripheral to the test system's
purpose. It seems better to put this logic in the lab itself, where is
can provide such support.
With Labgrid we can use the UbootStrategy class to get the board into a
useful state, however it needs to do it. Then it can report to pytest
by writing a suitable string along with the U-Boot version it detected.
Add support for detecting 'lab mode' and simply assume that all is well
in that case. Collect the version string when Labgrid says it is ready.
This is only used with the Labgrid-sjg integration. When Labgrid starts
the UbootStrategy it checks if U_BOOT_SOURCE_DIR is set. If so it emits
a string '{lab mode}' that tells test.py to simply wait for an
indication that the board is ready. All banner-checking is skipped. The
indication comes in the form of another string 'Lab: Board is ready'
which Labgrid sends once the board is sitting at a prompt ready to run
tests. Then test.py emits 'U-Boot is ready' and continues with testing.
Note that Labgrid has the same kind of "check for a string" logic that
is in test.py, except it's not caring about the correct number / order
of banner prints. This checking could be added, however. If something
fails, the complete output is shown, so it is possible to see what went
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
In Labgrid there is the concept of a 'role', which is similar to the
U-Boot board ID in U-Boot's pytest subsystem.
The role indicates both the target and information about the U-Boot
build to use. It can also provide any amount of other configuration.
The information is obtained using the 'labgrid-client query' operation.
Using this role, all required configuration for the board is stored
within the Labgrid environment, with pytest simply querying it. This
allows connecting to boards using an interactive console, something that
isn't possible without some kind of mapping. It also means that we don't
need to replicate the pytest functionality in tbot, since Labgrid can
handle the console and kick off builds as needed.
Make use of this in tests, so that only the role is required in gitlab
and other situations. The board type and other things can be queried
as needed.
Use a new 'u-boot-test-getrole' script to obtain the requested
information.
With this it is possible to run lab tests in gitlab with just a single
'ROLE' variable for each board.
Note that, without this feature:
- interactive use of boards with Labgrid-sjg would require repeating the
id/board in a separate configuration file
- Gitlab yaml file would need to specify both the id and board
This feature is entirely optional, however, with the code gracefully
falling back to using a separate ID and board.
Link: https://tbot.tools
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we know that the board is already running the right software,
so provide an option to allow running of tests directly, without first
resetting the board.
This saves time when re-running a test where only the Python code is
changing.
Note that this feature is open to errors, since the user must know that
the board is in a fit state to execute tests. It is useful for repeated
iteration on a particular test, where it can save quite a bit of time.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a board is finished with, the lab may want to power it off, or
perform some other function. Add a new script which is called when tests
are complete.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When Labgrid is used, it can get U-Boot ready for running tests. It
prints a message when it has done so.
Add logic to detect this message and accept it.
Note that this does not change pytest, which still (also) looks for the
U-Boot banner. This change merely makes it possible for pytest to
believe Labgrid when it says that the board is ready for use.
In several cases, the board starts up and Labgrid receives some initial
output, then pytest starts and misses some of that output, because it
came in while Labgrid had the console open. Then pytest fails because
it doesn't see the expected banners.
With this change, Labgrid handles getting U-Boot to a prompt, in a
fully reliable manner. Then pytest starts up and can simply start
running its tests.
But, again, this does not prevent pytest from handling a banner if one
is provided (e.g. if not using the Labgrid integration).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When mentioning a test name, add single quotes to make it easier to see.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This should show the test name, not the selected name, since the user
may be running all tests, in which case 'select_name' is NULL
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
Rather than returning various error codes, use assertions to check that
the test passes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
There is no particular need for the time tests to have their own test
command. Move them into the lib suite instead.
Update the test functions to match the normal unit-test signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the lib/
directory, to match its implementation. Rename it to drop the
unnecessary _ut suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
There is no particular need for the unicode tests to have their own test
suite. Move them into the lib suite instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the lib/
directory, to match its implementation. Rename it to drop the
unnecessary _ut suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
There is no particular need for the str tests to have their own test
suite. Move them into the lib suite instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the lib/
directory, to match (most of) its implementation. Rename it to drop the
unnecessary _ut suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
There is no particular need for bloblist to have its own test suite.
Move it into the common suite instead.
Add the missing help for 'common'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the common/
directory, to match its implementation. Rename it to drop the
unnecessary _ut suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the boot/
directory, to match its implementation.
This test is currently dependent on bloblist, but the real dependency is
on sandbox, so update that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
Rather than enabled DEBUG and using assert(), use the unit-test
functions now provided.
Drop a check that causes pytest to fail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
The command test was the very first test written in U-Boot, some 12
years ago. It predates the unit-test subsystem and was never converted
over.
There is no particular need for the command test to have its own
command. It is also confusing to have it separate from the normal test
suites. At present this test is not run in CI.
Move it into the cmd suite instead, updating it to become a unit test.
One of the checks is dropped to avoid an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the lib/
directory, since that is where compression is implemented.
Rename it to just 'command', since it is obviously a unit test and the
_ut suffix does not add much except to make it different from the names
of other test files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
There is no particular need for compression to have its own test suite.
Move it into the lib suite instead.
Add the missing help for 'common' and update the docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the lib/
directory, since that is where compression is implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
The trace feature is now tested in CI so there is no need for these old
script. Also they don't work. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This pointer is not used any more, so drop the declarations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
This test doesn't belong at the top level. Move it into the common/
directory, to match its implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
After calling strdup() check the returned pointer.
Avoid a memory leak if the directory is not found.
Reported-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Fixes: 22fdac381f ("fs: ext4: implement opendir, readdir, closedir")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This flag was lost by a previous change and has never been restored.
Without it, binman cannot fully handle missing blobs which are
themselves inputs to mkimage.
Discussion on this at [1] indicated that this was necessary but the
patch was not updated.
Restore the flag so that all missing blobs are reported.
Link: https://patchwork.ozlabs.org/project/uboot/patch/20221206020336.315465-1-trini@konsulko.com/
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 93685d0dcb ("Makefile: With BINMAN_ALLOW_MISSING=1 don't error")
qemu_arm64_defconfig with CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=n leads to a
build error:
arch/arm/lib/crt0_64.S:85:
Error: constant expression expected at operand 2 --
`ldr x0,=((CFG_SYS_INIT_RAM_ADDR+CFG_SYS_INIT_RAM_SIZE-480))'
We do not define CFG_SYS_INIT_RAM_ADDR and CFG_SYS_INIT_RAM_SIZE for QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have only implemented longjmp() on the EFI architectures.
Define a symbol CONFIG_HAVE_SETJMP and have it selected by the relevant
architectures.
Use CONFIG_HAVE_SETJMP to decide if the longjmp test shall be built.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Avoid a build failure when building with CONFIG_API=y, CONFIG_EXAMPLES=y:
lib/vsprintf.c:312:14: warning:
‘device_path_string’ defined but not used [-Wunused-function]
312 | static char *device_path_string(char *buf, char *end, void *dp, int field_width,
| ^~~~~~~~~~~~~~~~~~
Fixes: 64b5ba4d29 ("efi_loader: make device path to text protocol customizable")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Heinrich Schuchardt <heinrich.schuchardt@canonical.com> says:
The lib_test_uuid_to_le and lib lib_test_dynamic_uuid tests fail on
32-bit systems. But we never caught this in our CI because we never
ran any of our C unit tests on 32-bit.
Enable CONFIG_UNIT_TEST on qemu_arm_defconfig.
hextoul() cannot convert a string to a 64-bit number on a 32-bit system.
Use the new function hextoull() instead.
Link: https://lore.kernel.org/r/20241103224223.195255-1-heinrich.schuchardt@canonical.com
