This driver is not used by any system and is long unmaintained, drop it.
There is a DWC2 OTG driver which is maintained, see CONFIG_USB_GADGET_DWC2_OTG .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
only waiting for TXEMPTY leads to corrupted messages going over the
wire - which is fixed by making use of the FIFO
this change is following the linux kernel uart driver
(drivers/tty/serial/imx.c), which also checks UTS_TXFULL
instead of UTS_TXEMPTY
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
on imx8(mm) the RXDMUXSEL needs to be set for data going over the wire
(as observable on a connected 'scope) to actually make it into the
RXFIFO
the reference manual is not overly clear about this, and only
mentiones that "UCR3_RXDMUXSEL should always be set." - and since the
CR3 register reverts to its reset values after setting the baudrate,
setting this bit is done during '_mxc_serial_setbgr'
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The ddrphy_utils.c is now deduplicated in drivers/ddr/imx/phy/ddrphy_utils.c ,
this drivers/ddr/imx/imx8m/ddrphy_utils.c is a remnant from when the
deduplication was implemented and was not removed. Remove it as it is
unused.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
wrong end address passed to flush_dcache_range.
modified the flush_dache logic for scatter list elements.
Fixes: 1919f58a8f (crypto/fsl: fsl_hash: Fix dcache issue in caam_hash_finish)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
The i.MXRT11 series has different offsets for IOCR_MUX, it also can
address 64MiB of SDRAM so add a macro for that.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The i.MXRT11 series has two new pll types but are variants of existing.
This patch adds the ability to read one of the pll types' frequency
as it can't be changed unlike the generic pll it also has the
division factors swapped.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
While testing on some Kirkwood platforms it was noticed that the timer
did not function correctly all the time. The driver did not correctly
handle 32bit timer value wrap arounds. Using the timer_conv_64()
conversion function fixes this issue.
Fixes: e9e73d78a8 ("timer: add orion-timer support")
Suggested-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
This allows to concatenate SPL and proper U-Boot without extra alignment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
These two device tree properties were not being applied.
Fixes: 1fd9eb68d6 ("i2c: stm32f7: move driver data of each instance in a privdata")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Current function stm32_i2c_message_xfer is sending a STOP
whatever the result of the transaction is. This can cause issues
such as making the bus busy since the controller itself is already
sending automatically a STOP when a NACK is generated.
Thanks to Jorge Ramirez-Ortiz for diagnosing and proposing a first
fix for this. [1]
[1] https://lore.kernel.org/u-boot/20220815145211.31342-2-jorge@foundries.io/
Reported-by: Jorge Ramirez-Ortiz, Foundries <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Functions stm32_i2c_message_start and stm32_i2c_handle_reload
both get a stop boolean indicating if the transfer should end with
a STOP or not. However no specific handling is needed in those
functions hence remove the parameter.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bits should be set to 0, not 1.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
Fman microcode is executable code (AFAICT) loaded into a
coprocessor. As such, if verified boot is enabled, it must be verified
like other executable code. However, this is not currently done.
This commit adds verified boot functionality by encapsulating the
microcode in a FIT, which can then be signed/verified as normal. By
default we allow fallback to unencapsulated firmware, but if
CONFIG_FIT_SIGNATURE is enabled, then we make it mandatory. Because
existing Layerscape do not use this config (instead enabling
CONFIG_CHAIN_OF_TRUST), this should not break any existing boards.
An example (mildly-abbreviated) its is provided below:
/ {
#address-cells = <1>;
images {
firmware {
data = /incbin/(/path/to/firmware);
type = "firmware";
arch = "arm64";
compression = "none";
signature {
algo = "sha256,rsa2048";
key-name-hint = "your key name";
};
};
};
configurations {
default = "conf";
conf {
description = "Load FMAN microcode";
fman = "firmware";
};
};
};
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Several ethernet drivers load firmware from FIT images. Convert them to
use the fit_get_data helpers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Handle the input clock of RCC USB_PHY_48, provided by USBPHYC
and named "ck_usbo_48m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
ck_usbo_48m is generated by usbphyc PLL and used by OTG controller
for Full-Speed use cases with dedicated Full-Speed transceiver.
ck_usbo_48m is available as soon as the PLL is enabled.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the counter of the PLL user n_pll_cons managed by the 2 functions
stm32_usbphyc_pll_enable / stm32_usbphyc_pll_disable.
This counter allow to remove the function stm32_usbphyc_is_init
and it is a preliminary step for ck_usbo_48m introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
System reset via the SRST extension in the SBI should be the default.
The driver checks if the extension is available when probing.
So there is no risk in enabling it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This commit sychronizes the header file for FU740 PRCI clocks with the
one from Linux 5.19.
The constant values are the same, but all constant names are changed
(most are just prefixed with FU740_).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If ethernet connected to SFP, like this:
&enetc_port0 {
phy-connection-type = "sgmii";
sfp = <&sfp0>;
managed = "in-band-status";
status = "okay";
};
Then enetc_config_phy returns -ENODEV and the memory containing the mdio interface is freed.
It's better to unregister and free mdio resources.
Signed-off-by: Siarhei Yasinski <siarhei.yasinski@sintecs.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.
There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.
Fixes: e8a7f1c32b ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The interactive mode uses large several tables of options which can be
configured. However, much of the contents of these tables are
repetetive. For example, no struct is larger than half a kilobyte, so
the offset only takes up 9 bits. Similarly, the size is only ever 4 or
8, and printhex is a boolean. Reduce the size of these fields. This
reduces the size of the options tables by around 10 KiB. However, the
largest contributor to the size of the options tables is the use of a
pointer for the strings. A better approach would be to use a separate
array of strings, and store an integer index in the options tables.
However, this would require a large re-architecting of this file.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Adding some debug prints I can see:
MMC: mmc@fe320000: Got clock clock-controller@ff760000 76
mmc@fe310000: Got clock clock-controller@ff760000 77
Unknown clock 77
rockchip_dwmmc_get_mmc_clk: err=-2
mmc@fe310000: 3, mmc@fe320000: 1, mmc@fe330000: 0
According to kernel code the SDIO clock is identical to SDMMC clock
except for the con 16->15 change.
Add support for the clock to avoid the error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently the default initialisation frequency is 50MHz. Although
this does appear to be suitable for some LPDDR4 RAM chips, training at
this low frequency has been seen to cause Column errors, leading to
Capacity check errors on others.
Here we force RAM initialisation to happen at 400MHz before ramping up
to the final value running value of 800MHz after everything has been
successfully configured.
Link: https://lore.kernel.org/u-boot/Yo4v3jUeHXTovjOH@google.com/
Suggested-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Frequency changes to 400MHz are presently reported as:
lpddr4_set_rate_0: change freq to 400000000 mhz 0, 1
This is obviously wrong by 6 orders of magnitude.
Ensure frequency changes are reported accurately.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Functions pointed to by this op pointer can return non-zero values
indicating an error. Ensure any error value is propagated back up the
call-chain.
Signed-off-by: Lee Jones <lee@kernel.org>
Tested-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Only add the dram channel when we finally setup it successfully at the
last step.
Signed-off-by: Han Pengfei <pengphei@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is useful to read information about the current TPM state, where
supported, e.g. for debugging purposes when verified boot fails.
Add support for this to the TPM interface as well as Cr50. Add a simple
sandbox test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the emulator assumes that the TPM is inited in the same phase
where it is used. But in fact SPL may init the TPM, so we don't want to
complain when U-Boot proper later uses it. Remove this check.
It might be best to save this information into the device state for the
TPM, so that we can make sure the TPM was inited at some point. For now,
this seems good enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The host will report such error message if the fastboot device work in
full-speed mode: "Duplicate descriptor for config 1 interface 0
altsetting 0, skipping"
Fastboot device ack both full and high speed interface descriptors when
work in full-speed mode, that's will cause this issue.
Fix it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: John Keeping <john@metanate.com>
The compatible values used for device nodes representing Renesas Reduced
Pin Count Interfaces were based on preliminary versions of the Device
Tree Bindings.
Correct them in both DTSi files and drivers, to match the final DT
Bindings.
Note that there are no DT bindings for RPC-IF on RZ/A1 yet, hence the
most logical SoC-specific value is used, without specifying a
family-specific value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The brute-force controller disable method can end up racing controller
initialization and causing a crash when we shut down Apple ANS2 NVMe
controllers. Do a proper controlled shutdown, which does block until
things are quiesced properly. This is nicer in general for all
controllers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Tested-by: Mark Kettenis <kettenis@openbsd.org> (firefly-rk3399)
PCIe config space has address range 0-4095. So do not allow reading from
addresses outside of this range. Lot of U-Boot drivers do not expect that
passed value is not in this range. PCI DM read function is extended to
fill read value to all ones or zeros when it fails as U-Boot callers
ignores return value.
Calling U-Boot command 'pci display.b 0.0.0 0 0x2000' now stops printing
config space at the end (before 0x1000 address).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The gpio-button driver depends on DM_GPIO, add it to Kconfig to avoid
build errors.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Add timer support for Kirkwood and MVEBU devices.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
