Add instructions on how to build and package OP-TEE for the
phycore-imx8mm based boards. The build instructions are identical for
phyGATE-Tauri-L and phyBOARD-Polis.
Also fix missig '-' for TF-A build instructions.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Add documentation for the phyBOARD-Pollux i.MX 8M Plus on OP-TEE
integration.
Also add missing '-' to TF-A build instruction while at it.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Garrett Giordano <ggiordano@phytec.com> says:
This patch set adds the phyCORE AM62Ax board support and documenation to
u-boot.
The phyCORE-AM62Ax is a SoM (System on Module) featuring TI's AM62Ax SoC. It can
be used in combination with different carrier boards. This module can come
with different sizes and models for DDR, eMMC, SPI NOR Flash and various SoCs
from the AM62x family.
A development Kit, called phyBOARD-Lyra is used as a carrier board reference
design around the AM62x SoM.
This series depends on the following two patches:
- [PATCH v2] arm: mach-k3: am62a7: Provide a way to obtain boot device for non SPL
https://lists.denx.de/pipermail/u-boot/2024-October/570156.html
- [PATCH] board: phytec: common: Introduce CONFIG_PHYTEC_K3_DDR_PATCH
https://lists.denx.de/pipermail/u-boot/2024-November/571543.html
Link: https://lore.kernel.org/r/20241118231606.3161665-1-ggiordano@phytec.com
[trini: Fix warning in board/phytec/common/k3/board.c when
CONFIG_EFI_HAVE_CAPSULE_SUPPORT is not enabled]
Signed-off-by: Tom Rini <trini@konsulko.com>
The phyCORE-i.MX 93 is available in various variants (e.g. different ram
sizes, eMMC HS400 yes/no). Enable hardware introspection for the
imx93-phyboard-segin_defconfig, so that during startup the SOM module
variant can be detected, and the hardware can be configured accordingly.
The resulting SPL and u-boot binary shall able to boot each
phyCORE-i.MX 93 module variant on each carrier board. Finally rename
imx93-phyboard-segin_defconfig to imx93-phycore_defconfig, to highlight
its SOM scope.
Signed-off-by: Christoph Stoidner <c.stoidner@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Add support for packaging the TIFS Stub as it's required for basic Low
Power Modes like Deep Sleep.
The reason it is packaged using binman and not inherently as part of the
DM firmware is because for HS devices, customer owns the customer key
and only customer has access to it.
DM is release by TI, Since TI doesn't have access to the customer key it
cannot have a component that is signed by customer key.
Hence, it's left as part of binman to be signed and packaged.
While at it, also make sure it's documented in phycore-am62x
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Use the new boot_firmwares labels that help make documentation more
specific as to which firmwares are used in which devices
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Update Flash to SPI NOR chapter for use with mtd commands.
This is more convenient as we do not have to remember any
offsets in the SPI.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
We moved our documentation to another hoster and therefore the URL
changed. Point to the latest documentation instead of release versions
to not link out-dated documentation.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Add brief documentation on how to build a bootable U-Boot image for the
phyGATE-Tauri-L.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
