It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt <heinrich.schuchardt@canonical.com> says:
Since commit 348ea87850 ("cmd: hash: fix param count check") the hash
command cannot be used without the optional variable name parameter if
CONFIG_HASH_VERIFY=y. 'hash sha1 $loadaddr $filesize' returns
CMD_RET_USAGE.
The minimum number of arguments is four no matter if verification is
enabled or not.
Fix the parameter check.
Provide a unit test.
Link: https://lore.kernel.org/r/20241102100836.103005-1-heinrich.schuchardt@canonical.com
This test doesn't belong at the top level. Move it into the lib/
directory, since that is where compression is implemented.
Rename it to just 'command', since it is obviously a unit test and the
_ut suffix does not add much except to make it different from the names
of other test files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> # rpi_3, rpi_4, rpi_arm64, am64x_evm_a53, am64-sk
Currently, the "dm" suite in unit tests (ut) is only available on
sandbox. Make sure that all cmd tests that are part of this suite are
only available on sandbox and not attempted to be run on hardware (where
it will fail to be able to be started).
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
U-Boot has a fairly rigid memory map which is normally not visible
unless debugging is enabled in board_f.c
Update the 'meminfo' command to show it. This command does not cover
arch-specific pieces but gives a good overview of where things are.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to obtain the results of MSR queries as well as to update
MSR registers, so add a command these tasks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Prepare the introduction of the lwIP (lightweight IP) TCP/IP stack by
adding a new net/lwip/ directory and the NET_LWIP symbol. Network
support is either NO_NET, NET (legacy stack) or NET_LWIP. Subsequent
commits will introduce the lwIP code, re-work the NETDEVICE integration
and port some of the NET commands and features to lwIP.
SPL_NET cannot be enabled when NET_LWIP=y. SPL_NET pulls some symbols
that are part of NET (such as arp_init(), arp_timeout_check(),
arp_receive(), net_arp_wait_packet_ip()). lwIP support in SPL may be
added later.
Similarly, DFU_TFTP and FASTBOOT are not compatible with NET_LWIP
because of dependencies on net_loop(), tftp_timeout_ms,
tftp_timeout_count_max and other NET things. Let's add a dependency on
!NET_LWIP for now.
SANDBOX can select NET_LWIP but doing so will currently disable the eth
dm tests as well as the wget tests which have strong dependencies on the
NET code.
Other adjustments to Kconfig files are made to fix "unmet direct
dependencies detected" for USB_FUNCTION_SDP and CMD_FASTBOOT when
the default networking stack is set to NET_LWIP ("default NET_LWIP"
instead of "default NET" in Kconfig).
The networking stack is now a choice between NO_NET,
NET and NET_LWIP. Therefore '# CONFIG_NET is not set' should be
'CONFIG_NO_NET=y'. Adjust the defconfigs accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a new suite for 'cmd' tests, used for testing commands. These are
kept in the test/cmd directory.
For now it is empty, but it will be used for coreboot-command tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Current code allows up to 3 MBR partitions without extended one.
If more than 3 partitions are required, then extended partition(s)
must be used.
This commit allows up to 4 primary MBR partitions without the
need for extended partition.
Add mbr test unit. In order to run the test manually, mmc6.img file
of size 12 MiB or greater is required in the same directory as u-boot.
Test also runs automatically via ./test/py/test.py tool.
Running mbr test is only supported in sandbox mode.
Signed-off-by: Alex Gendin <agendin@matrox.com>
[ And due to some further changes for testing ]
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide armffa command showcasing the use of the U-Boot FF-A support
armffa is a command showcasing how to invoke FF-A operations.
This provides a guidance to the client developers on how to
call the FF-A bus interfaces. The command also allows to gather secure
partitions information and ping these partitions. The command is also
helpful in testing the communication with secure partitions.
For more details please refer to the command documentation [1].
A Sandbox test is provided for the armffa command.
[1]: doc/usage/cmd/armffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Sandbox test for the armffa command
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Adds a test for the new pci_mps command to ensure that it can set the
Maximum Payload Size (MPS) of all devices to 256 bytes in the sandbox
environment. Enables the pci_mps command in the sandbox environment so
that this test can be run.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a test which validates that exit from environment script works as
expected, including return value propagation and clipping to positive
integers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Simulate a TCP HTTP server's response for testing wget command.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.
Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.
Signed-off-by: Simon Glass <sjg@chromium.org>
The test relies on memory being available at 0x0. This in not valid for
many boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This command is being introduced with the goal of allowing user-friendly
"generic use case" U-Boot builds to pause until user input under some
situations.
The main use case would be when a boot failure happens, to pause until
the user has had time to acknowledge the current state.
Tested using:
make && ./u-boot -v -T -c 'ut lib lib_test_hush_pause'
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Simon Glass <sjg@chromium.org>
Add a basic test of the 'fdt addr' command, to kick things off.
This includes a new convenience function to run a command from a printf()
string.
Signed-off-by: Simon Glass <sjg@chromium.org>
cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.
So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.
ex: loadm $kernel_addr $kernel_addr_r $kernel_size
with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Allow pin name parameter for pimux staus command,
as gpio command to get status of one pin.
The possible usage of the command is:
> pinmux dev pinctrl
> pinmux status
> pinmux status -a
> pinmux status <pin-name>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a basic test for the newly introduced 'addrmap' command.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Rebase]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
test/cmd/setexpr.c cannot be linked with CONFIG_CMD_SETEXPR=n:
ld.bfd: test/built-in.o: in function `setexpr_test_sub':
test/cmd/setexpr.c:227: undefined reference to `setexpr_regex_sub'
ld.bfd: test/built-in.o: in function `setexpr_test_backref':
test/cmd/setexpr.c:267: undefined reference to `setexpr_regex_sub'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the command "pwm" for controlling the pwm channels. This
command provides pwm invert/config/enable/disable functionalities
via PWM uclass drivers
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This command currently has no tests. Add some for basic assignment and the
integer operations.
Note that the default size for setexpr is ulong, which varies depending on
the build machine. So for sandbox on a 64-bit host, this means that the
default size is 64 bits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add various fixes and improvements to this command that were missed in
the original version. Unfortunately I forgot to send v2.
- Fix Kconfig name
- Use a separate variable for the remaining search length
- Correct a minor bug
- Move into a separate test suite
- Add -q flag to the 'quiet' test to test operation when console is enabled
- Enable the feature for sandbox
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to find hex values and strings in a memory range.
Add a command to support this.
cmd: Fix 'md' and add a memory-search command
At present 'md.q' is broken. This series provides a fix for this. It also
implements a new memory-search command called 'ms'. It allows searching
memory for hex and string data.
END
Signed-off-by: Simon Glass <sjg@chromium.org>
