At present there is a hex value SPL_STACK which both determines whether
SPL has its own initial stack and the hex value of that stack.
Split off the former into SPL_HAVE_INIT_STACK with SPL_STACK depending
on that and only providing the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync defconfig files]
Deduplicate the config files again, move CONFIG_BOOTCOUNT_ALTBOOTCMD
into common imx8m_data_modul.config .
Fixes: 940135eea5 ("Kconfig: Move CONFIG_BOOTCOUNT_ALTBOOTCMD to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Add CONFIG_BOOTCOUNT_ALTBOOTCMD so the developer is able to add
custom altbootcmd via Kconfig when they enable BOOTCOUNT. With this now
in Kconfig, we need to move it from environment files / config.h files
and in to the defconfig file.
This was done by generating u-boot-initial-env for all platforms before
the Kconfig change, to extract altbootcmd values and then again after to
compare the result.
[trini: Perform migration to defconfigs, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
Deduplicate defconfigs for all Data Modul i.MX8M eDM SBC systems by factoring
out the common parts into generic imx8m_data_modul.config and including
those using the #include <configs/...> preprocessor macro in the current
set of board specific defconfigs. The preprocessor macro is applicable
to defconfigs as well.
This introduces no functional change, the resulting .config is almost
identical for all Data Modul i.MX8M eDM SBC systems, except for slight
alignment in DEBUG_UART and SYS_PBSIZE.
Signed-off-by: Marek Vasut <marex@denx.de>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable 'cat' command to print file from filesystem to stdout.
Enable 'xxd' command to hexdump file from filesystem to stdout.
Signed-off-by: Marek Vasut <marex@denx.de>
Switch PHY_ANEG_TIMEOUT to CONFIG_PHY_ANEG_TIMEOUT Kconfig symbol.
This removes one more configuration headers option finalizes its
Kconfig symbol conversion. No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Linux 6.6.y with KASLR enabled would print the following message on boot:
"
KASLR disabled due to lack of seed
"
Enable the 'kaslrseed' command so a random number seed can be pulled
from CAAM and inserted into the /chosen node 'kaslr-seed' property of
Linux kernel DT before boot, thus letting KASLR work properly.
Signed-off-by: Marek Vasut <marex@denx.de>
The CONFIG_SPL_BOARD_INIT lets SPL common code call spl_board_init()
during the SPL start up. On this particular system, spl_board_init()
is used to reconfigure GIC clock parent to PLL2 500M, which is the
configuration expected by the Linux kernel. Enable SPL_BOARD_INIT
and fill in the GIC clock configuration code.
Set GIC clock to 500 MHz for OD VDD_SOC. Kernel driver does not
allow to change it. Should set the clock after PMIC setting done.
Default is 400 MHz (system_pll1_800m with div = 2) set by ROM for
ND VDD_SOC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Use default SAVED_DRAM_TIMING_BASE as that is what upstream TFA expects.
Without this change, the board will fail to suspend/resume e.g. in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
