Users experiencing random kernel crashes due to new versions of
Marvell's DDR training algorithm can solve the issue by setting DDR
speed to 1333H.
But if kernel crashes, it has to be done in U-Boot, which is impossible
without UART connection.
In order to make it easier for users, use the rescue button mechanism:
when rescue mode 9 is selected (that is when 10 LEDs are ON), U-Boot
will train DDR in 1333H mode and also update EEPROM so that subsequent
boot will use this mode.
User has to use the `eeprom` command in U-Boot or `omnia-eeprom` command
in OS to switch back to 1600K mode.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the i2c_eeprom miscellaneous driver for reading Turris Omnia EEPROM
in U-Boot proper. Keep using dm_i2c_read() in SPL build, since adding
the i2c_eeprom driver to SPL build increases the image by 1.5 KiB.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename the variable holding the EEPROM udevice from `chip` to `eeprom`.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't set many options in the board Kconfig entry file but instead
use defconfigs, select in some cases on the target itself, or update the
"default" options of the main entries when needed. In this case we can
remove most of the board Kconfig entries and just add them to the
defconfig like other platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Support old DDR3 training code on Turris Omnia, selectable via EEPROM
field.
Users experiencing DDR3 initialization failures or random crashes of the
operating system due to incorrect DDR3 configuration can select the old
DDR3 training implementation to fix those issues by setting the EEPROM
field "Use old DDR training":
eeprom update "Use old DDR training" 1
Signed-off-by: Marek Behún <kabel@kernel.org>
Some Turris Omnia boards experience memory issues, and by
experimentation we found that some of these issues can be solved by
slowing DDR speed.
Add a new field in the extended EEPROM information structure, ddr_speed.
Support several values in this field (for now 1066F, 1333H, and the
default, 1600K) and use it to overwrite the DDR topology parameters
used by the DDR training algorithm.
Signed-off-by: Marek Behún <kabel@kernel.org>
Implement Turris Omnia EEPROM layout for the 'eeprom' command.
When the 'eeprom' command (with layout support) is enabled, we can now
use the 'eeprom print' and 'eeprom update' commands, for example:
=> eeprom print
Magic constant 34a04103
RAM size in GB 2
Wi-Fi Region
CRC32 checksum cecbc2a1
Signed-off-by: Marek Behún <kabel@kernel.org>
For board revisions where the WAN ethernet PHY reset GPIO is controllable
via MCU we currently insert a phy-reset-gpios property into the ethernet
controller node. The mvneta driver parses this property and uses the
GPIO to reset the PHY.
But this phy-reset-gpios property is not a valid DT binding in upstream
kernel. Instead, a reset-gpios property should be inserted into the
ethernet PHY node. This correct DT binding is supported by the DM ETH PHY
U-Boot driver.
Insert the reset-gpios property into the WAN PHY node instead the
phy-reset-gpios property in WAN ETH node so that Linux will correctly use
the reset GPIO.
Enable the CONFIG_DM_ETH_PHY config option so that U-Boot will also use
the correct DT property.
Note: currently there are 4 ethernet controller drivers parsing the
wrong DT property: dwc_eth_qos, fex_mxc, mvneta and mvpp2. We should
convert all relevant device-trees to use reset-gpios so that we can get
rid of these drivers parsing this property.
Fixes: 1da53ae26a ("arm: mvebu: turris_omnia: Add support for design with SW reset signals")
Signed-off-by: Marek Behún <kabel@kernel.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>
If the FEAT_CRYPTO feature bit is present in MCU features, the board
crypto is implemented by MCU and the Atmel SHA chip is not present.
Disable Atmel SHA device-tree node in that case.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
If MCU supports the FEAT_CRYPTO feature, read board ECDSA public key
from MCU and print it.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement reading board serial number, first MAC address and board
version from MCU. MCU supports board information if the FEAT_BOARD_INFO
feature bit is set in MCU features.
Prefer getting board information from MCU if supported, fallback to
Atmel SHA chip.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor MCU status word and MCU firmware features reading to make it
simpler to use.
Try reading 32 bits of features, if that fails, read 16 bits. Older MCU
firmware supports only 16-bit wide features, and if more bytes are read,
either 0xff is sent or I2C transaction fails. Handle both cases.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Since commit 8cd4bf7dc9 ("turris: Use checkboard() instead of
show_board_info()") the model is show two times during boot:
Model: Turris Omnia
Model: Turris Omnia
This is because the common function show_board_info() shows it, and
Turris' checkboard() also does.
Remove the second print.
Fixes: 8cd4bf7dc9 ("turris: Use checkboard() instead of show_board_info()")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add header containing all MCU command definitions and use it in board
code and in MCU driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When rescue mode was activated reset also bootdelay env variable to its
default value. This will ensure that reset button works and starts rescue
mode also in the case when user changed bootdelay env variable to -1 (which
has meaning to not start autoboot).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Store serial number from atsha cryptochip into the serial# env variable.
U-Boot automatically puts content of this variable into the root device
tree property serial-number when booting Linux kernel. Refactor turris
atsha code and from turris_atsha_otp_get_serial_number() function returns
directly string suitable for printing or storing into device tree. Because
during different boot stages is env storage read-only, it is not possible
to always store serial number into env storage. So introduce a new function
turris_atsha_otp_init_serial_number() which is called at later stage and
which ensures that serial number is correctly stored into env.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When Mox SFP module is connected after Topaz or Peridot module then port DT
node already contains "sfp" label. But Mox SFP module can be connected also
without Topaz or Peridot module in which case it is connected directly into
he eth1 DT node, which is without any label. So add "sfp" label into eth1
DT node in this case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel DTS files renamed spi-nor@0 node to flash@0 which effectively
broke U-Boot to boot new Linux kernel versions correctly.
So remove hardcoded spi-nor device tree path from Turris Omnia board code
and replace it by searching for mtd node by compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Sometimes fixup_mtd_partitions() prints during booting kernel error
"Failed fixing SPI NOR partitions!" because it does not have enough space
for creating all paritions nodes. So increase fdt size.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
All partitions are created by fixup_mtd_partitions() function, so they do
not have to exist just for their removal need.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
New Turris Omnia HW board revision requires that software controls
peripheral reset signals, namely PERST# signals on mPCIe slots, ethernet
phy reset and lan switch reset. Those pins are connected to MCU controlled
by MCU i2c API as GPIOs. On new HW board revision those pins stay in reset
after board reset and software has to release these peripherals from reset
manually. MCU announce this requirement by FEAT_PERIPH_MCU bit in
CMD_GET_FEATURES command.
On older HW board revisions when FEAT_PERIPH_MCU is not announced, all
those reset signals are automatically released after board finish reset.
Detect FEAT_PERIPH_MCU bit in board_fix_fdt() and ft_board_setup()
functions and insert into device tree blob pcie "reset-gpios" and eth phy
"phy-reset-gpios" properties with corresponding MCU gpio definitions.
PCIe and eth PHY drivers then automatically release resets during device
initialization. Both U-Boot and Linux kernel drivers support those device
tree reset properties.
Initialization of lan switch on new HW board revision is more complicated.
Switch strapping pins are shared with switch RGMII pins. And strapping pins
must be in specific configuration after releasing switch reset. Due to pin
sharing, it is first required to switch A385 side of switch pins into GPIO
mode, set strapping configuration, release switch from reset and after that
switch A385 pins back to RGMII mode.
Because this complicated setup is not supported by switch DSA drivers and
cannot be expressed easily in device tree, implement it manually in SPL
function spl_board_init(). So in proper U-Boot and OS/kernel would be lan
switch initialized and be in same configuration like it was on old HW board
revisions (where reset sequence did those steps at hardware level).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Different Turris Omnia HW board revisions contains different MCU.
Show type in show_board_info() to easily identify which MCU is populated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix MAINTAINERS files for Turris devices, add missing files and add Pali
as maintainer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
It does not matter what is DT node name of atsha device. So find it via
atsha driver and not by DT node name.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCIe Mini CEM 2.1 spec added support for USB3.0 mode on MiniPCIe cards.
USB3.0 and PCIe share same pins and only one function can be active at the
same time. PCIe Mini CEM 2.1 spec says that determining function is
platform specific and spec does not define any dedicated pin which could
say if card is USB3.0-based or PCIe-based.
Implement this platform specific decision (USB3.0 vs PCIe) for WWAN
MiniPCIe slot on Turris Omnia via U-Boot env variable "omnia_wwan_slot",
similarly like is implemented forced mode for MiniPCIe/mSATA slot via
"omnia_msata_slot" env variable. Value "usb3" for "omnia_wwan_slot" would
mean to set USB3.0 mode and value "pcie" original PCIe mode.
A385 SoC on Turris Omnia has configurable fifth SerDes line (exported to
MiniPCIe WWAN slot with SIM card) either to USB3.0 or PCIe functionality,
so implementation of this new PCIe Mini CEM 2.1 feature is simple, by just
configuring SerDes to USB 3.0 mode.
Other twos MiniPCIe slots on Turris Omnia do not have this new
functionality as their SerDes lines cannot be switched to USB3.0
functionality.
Note that A385 SoC does not have too many USB3.0 blocks, so activating
USB3.0 in MiniPCIe cause that one external USB3.0 USB-A port would loose
USB3.0 functionality and would be downgraded just to USB2.0.
By default this MiniPCIe WWAN slot is in PCIe mode, like before.
To set this MiniPCIe WWAN slot to USB3.0 mode, call U-Boot commands:
=> setenv omnia_wwan_slot usb3
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
