BL2_AT_EL3 is an overloaded macro which has two uses:
1. When BL2 is entry point into TF-A(no BL1)
2. When BL2 is running at EL3 exception level
These two scenarios are not exactly same even though first implicitly
means second to be true. To distinguish between these two use cases we
introduce new macros.
BL2_AT_EL3 is renamed to RESET_TO_BL2 to better convey both 1. and 2.
Additional macro BL2_RUNS_AT_EL3 is added to cover all scenarious where
BL2 runs at EL3 (including four world systems).
BREAKING CHANGE: BL2_AT_EL3 renamed to RESET_TO_BL2 across the
repository.
Change-Id: I477e1d0f843b44b799c216670e028fcb3509fb72
Signed-off-by: Arvind Ram Prakash <arvind.ramprakash@arm.com>
Signed-off-by: Maksims Svecovs <maksims.svecovs@arm.com>
If ARM_ARCH_MAJOR is 9 and ARM_ARCH_MINOR is 0 we don't want need to
have "-march=armv8-a+crc" in BL2_CPPFLAGS.
Change-Id: I9ac11522fde00953da40b95eebf82ff8ab2559ba
Signed-off-by: Diego Sueiro <diego.sueiro@arm.com>
Added a platform function to set and get DRTM error.
Also, added a platform function to reset the system.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I471f2387f8c78b21a06af063a6fa02cda3646557
Added Event Log driver support for DRTM. This driver
is responsible for the doing the hash measurement of
various DRTM components as per [1], and putting these
measurements in the Event Log buffer.
[1]: https://developer.arm.com/documentation/den0113/a, section 3.16
Change-Id: I9892c313cf6640b82e261738116fe00f7975ee12
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
DRTM implementation needs crypto support in BL31 to calculate
hash of various DRTM components
Signed-off-by: Manish V Badarkhe <manish.badarkhe@arm.com>
Change-Id: I659ce8e54550946db253d23f150cca8b2fa7b880
The Arm(R) Ethos(TM)-N NPU driver now supports configuring the SMMU
streams that the NPU shall use and will therefore no longer delegate
access to these registers to the non-secure world. In order for the
driver to support this, the device tree parsing has been updated to
support parsing the allocators used by the NPU and what SMMU stream that
is associated with each allocator.
To keep track of what NPU device each allocator is associated with, the
resulting config from the device tree parsing will now group the NPU
cores and allocators into their respective NPU device.
The SMC API has been changed to allow the caller to specify what
allocator the NPU shall be configured to use and the API version has
been bumped to indicate this change.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I6ac43819133138614e3f55a014e93466fe3d5277
According to Arm CCA security model [1],
"Root world firmware, including Monitor, is the most trusted CCA
component on application PE. It enforces CCA security guarantees for
not just Realm world, but also for Secure world and for itself.
It is expected to be small enough to feasibly fit in on-chip memory,
and typically needs to be available early in the boot process when
only on-chip memory is available."
For these reasons, it is expected that "monitor code executes entirely
from on-chip memory."
This precludes usage of ARM_BL31_IN_DRAM for RME-enlightened firmware.
[1] Arm DEN0096 A.a, section 7.3 "Use of external memory by CCA".
Change-Id: I752eb45f1e6ffddc7a6f53aadcc92a3e71c1759f
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
With RSS now introduced, we have 2 Measured Boot backends. Both backends
can be used in the same firmware build with potentially different hash
algorithms, so now there can be more than one hash algorithm in a build.
Therefore the logic for selecting the measured boot hash algorithm needs
to be updated and the coordination of algorithm selection added. This is
done by:
- Adding MBOOT_EL_HASH_ALG for Event Log to define the hash algorithm
to replace TPM_HASH_ALG, removing reference to TPM.
- Adding MBOOT_RSS_HASH_ALG for RSS to define the hash algorithm to
replace TPM_HASH_ALG.
- Coordinating MBOOT_EL_HASH_ALG and MBOOT_RSS_HASH_ALG to define the
Measured Boot configuration macros through defining
TF_MBEDTLS_MBOOT_USE_SHA512 to pull in SHA-512 support if either
backend requires a stronger algorithm than SHA-256.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I4ddf06ebdc3835beb4d1b6c7bab5a257ffc5c71a
- Use the development PROTPK and SWD_ROTPK if using cca CoT.
- Define a cca CoT build flag for the platform code to provide
different implementations where needed.
- When ENABLE_RME=1, CCA CoT is selected by default on Arm
platforms if no specific CoT is specified by the user.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I70ae6382334a58d3c726b89c7961663eb8571a64
diphda platform is now being renamed to corstone1000.
These changes are to replace all the instances and traces
of diphda corstone1000.
Change-Id: I330f3a112d232b99b4721b6bf0236253b068dbba
Signed-off-by: Arpita S.K <Arpita.S.K@arm.com>
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>
The Event Log sources are added to the source-list of BL1 and BL2
images in the Event Log Makefile. It doesn't seem correct since
some platforms only compile Event Log sources for BL2.
Hence, moved compilation decision of Event Log sources to the
platform makefile.
Change-Id: I1cb96e24d6bea5e091d08167f3d1470d22b461cc
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
As Measured-Boot and Trusted-Boot are orthogonal, removed
Trusted-Boot's dependency on Measured-Boot by allowing them
to apply the Crypto module changes independently using the
CRYPTO_SUPPORT build flag.
Change-Id: I5a420e5d84f3fefe0c0092d822dab981e6390bbf
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
There might be several platforms which use the
TARGET_PLATFORM build option to differentiate the code
between the platform variants.
Use of TARGET_PLATFORM in the common code leads to build
failures instead use PLAT build option.
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Change-Id: I9724caf875bd56225e035ecffa8b9ca1a50d3401
It doesn't look correct to use mbed TLS defines directly in the Event
Log driver as this driver may use another Crypto library in future.
Hence mbed TLS Crypto dependency on Event Log driver is removed by
introducing generic Crypto defines and uses those in the Event Log
driver to call Crypto functions.
Also, updated mbed TLS glue layer to map these generic Crypto defines
to mbed TLS library defines.
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ibc9c751f60cbce4d3f3cf049b7c53b3d05cc6735
Including the FCONF Makefile today automatically places the FCONF
sources into the source list of the BL1 and BL2 images. This may be
undesirable if, for instance, FCONF is only required for BL31.
This change moves the BL1 and BL2 source appends out of the common
Makefile to where they are required.
BREAKING CHANGE: FCONF is no longer added to BL1 and BL2 automatically
when the FCONF Makefile (`fconf.mk`) is included. When including this
Makefile, consider whether you need to add `${FCONF_SOURCES}` and
`${FCONF_DYN_SOURCES}` to `BL1_SOURCES` and `BL2_SOURCES`.
Change-Id: Ic028eabb7437ae95a57c5bcb7821044d31755c77
Signed-off-by: Chris Kay <chris.kay@arm.com>
This has been introduced to simplify dependencies on the FDT wrappers.
We generally want to avoid pulling in components on a file-by-file
basis, particularly as we are trying to draw conceptual boxes around
components in preparation for transitioning the build system to CMake,
where dependencies are modelled on libraries rather than files.
Signed-off-by: Chris Kay <chris.kay@arm.com>
Change-Id: Idb7ee05a9b54a8caa3e07f36e608867e20b6dcd5
With the removal of the generic functions measured_boot_init()/finish(),
measured_boot.mk becomes specific to the TCG event log backend. Change
its file name to event_log.mk.
Also, the Event Log driver is one of the backend of measured boot hence
created a separate folder for it under the measured_boot directory.
Alongside done some cosmetic changes (adding a comment and fixing
identation).
Change-Id: I4ce3300e6958728dc15ca5cced09eaa01510606c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
In the typical TF-A boot flow, the Trusted Watchdog is started
at the beginning of BL1 and then stopped in BL1 after returning
from BL2. However, in the RME boot flow there is no return path
from BL2 to BL1. Therefore, disable the Watchdog if ENABLE_RME is set.
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>
Change-Id: Id88fbfab8e8440642414bed48c50e3fcb23f3621
We currently use ARM_PRELOADED_DTB_BASE build
variable to pass the kernel DTB base address to
the kernel when using the ARM_LINUX_KERNEL_AS_BL33
option. However this variable doesn't actually
change the DTB load address.
The DTB load address is actually specified in the
FW_CONFIG DTS (fvp_fw_config.dts) as 'hw_config'.
This patch passes the hw_config value instead of
ARM_PRELOADED_DTB_BASE allowing us to change
the kernel DTB load address through
fvp_fw_config.dts.
With this change we don't need the ARM_PRELOADED_DTB_BASE
build variable if RESET_TO_BL31 is not set.
Note that the hw_config value needs to be within the
ARM_DTB_DRAM_NS region specified by FVP_DTB_DRAM_MAP_START
and FVP_DTB_DRAM_MAP_SIZE.
This patch also expands the ARM_DTB_DRAM_NS region to 32MB.
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>
Change-Id: Idd74cdf5d2c649bb320644392ba5d69e175a53a9
Adding load, authentication, and transfer functionality from FVP R BL1 to
BL33, which will be the partner runtime code.
Signed-off-by: Lauren Wehrmeister <lauren.wehrmeister@arm.com>
Change-Id: I293cad09739dacac0d20dd57c1d98178dbe84d40
For v8-R64, especially R82, creating code to run BL1 at EL2, using MPU.
Signed-off-by: Gary Morrison <gary.morrison@arm.com>
Change-Id: I439ac3915b982ad1e61d24365bdd1584b3070425
Currently the SP package loading mechanism is only enabled when S-EL2
SPMC is selected. Remove this limitation.
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Change-Id: I5bf5a32248e85a26d0345cacff7d539eed824cfc
Renamed hw_crc32 to tf_crc32 to make the file and function
name more generic so that the same name can be used in upcoming
software CRC32 implementation.
Change-Id: Idff8f70c50ca700a4328a27b49d5e1f14d2095eb
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Added firmware update support in Arm platforms by using
FWU platform hooks and compiling FWU driver in BL2
component.
Change-Id: I71af06c09d95c2c58e3fd766c4a61c5652637151
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This commit enables trusted-firmware-a with Trusted Board Boot support
for the Diphda 64-bit platform.
Diphda uses a FIP image located in the flash. The FIP contains the
following components:
- BL2
- BL31
- BL32
- BL32 SPMC manifest
- BL33
- The TBB certificates
The board boot relies on CoT (chain of trust). The trusted-firmware-a
BL2 is extracted from the FIP and verified by the Secure Enclave
processor. BL2 verification relies on the signature area at the
beginning of the BL2 image. This area is needed by the SecureEnclave
bootloader.
Then, the application processor is released from reset and starts by
executing BL2.
BL2 performs the actions described in the trusted-firmware-a TBB design
document.
Signed-off-by: Rui Miguel Silva <rui.silva@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Change-Id: Iddb1cb9c2a0324a9635e23821c210ac81dfc305d
For Arm platforms PIE is enabled when RESET_TO_BL31=1 in aarch64 mode on
the similar lines enable PIE when RESET_TO_SP_MIN=1 in aarch32 mode.
The underlying changes for enabling PIE in aarch32 is submitted in
commit 4324a14bf
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ib8bb860198b3f97cdc91005503a3184d63e15469
Added support for HW computed CRC using Arm ACLE intrinsics.
These are built-in intrinsics available for ARMv8.1-A, and
onwards.
These intrinsics are enabled via '-march=armv8-a+crc' compile
switch for ARMv8-A (supports CRC instructions optionally).
HW CRC support is enabled unconditionally in BL2 for all Arm
platforms.
HW CRC calculation is verified offline to ensure a similar
result as its respective ZLib utility function.
HW CRC calculation support will be used in the upcoming
firmware update patches.
Change-Id: Ia2ae801f62d2003e89a9c3e6d77469b5312614b3
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Added GPT parser support in BL2 for Arm platforms to get the entry
address and length of the FIP in the GPT image.
Also, increased BL2 maximum size for FVP platform to successfully
compile ROM-enabled build with this change.
Verified this change using a patch:
https://review.trustedfirmware.org/c/ci/tf-a-ci-scripts/+/9654
Change-Id: Ie8026db054966653b739a82d9ba106d283f534d0
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
NOTE: Breaking change to the way UUIDs are stored in the DT
Currently, UUIDs are stored in the device tree as
sequences of 4 integers. There is a mismatch in endianness
between the way UUIDs are represented in memory and the way
they are parsed from the device tree. As a result, we must either
store the UUIDs in little-endian format in the DT (which means
that they do not match up with their string representations)
or perform endianness conversion after parsing them.
Currently, TF-A chooses the second option, with unwieldy
endianness-conversion taking place after reading a UUID.
To fix this problem, and to make it convenient to copy and
paste UUIDs from other tools, change to store UUIDs in string
format, using a new wrapper function to parse them from the
device tree.
Change-Id: I38bd63c907be14e412f03ef0aab9dcabfba0eaa0
Signed-off-by: David Horstmann <david.horstmann@arm.com>
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
So far the ARM platform Makefile would require that RESET_TO_BL31 is set
when we ask for the ARM_LINUX_KERNEL_AS_BL33 feature.
There is no real technical reason for that, and the one place in the
code where this was needed has been fixed.
Remove the requirement of those two options to be always enabled
together.
This enables the direct kernel boot feature for the Foundation FVP
(as described in the documentation), which requires a BL1/FIP
combination to boot, so cannot use RESET_TO_BL31.
Change-Id: I6814797b6431b6614d684bab3c5830bfd9481851
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Implemented a parser which populates the properties of
the CoT descriptors as per the binding document [1].
'COT_DESC_IN_DTB' build option is disabled by default and can
be enabled in future for all Arm platforms by making necessary
changes in the memory map.
Currently, this parser is tested only for FVP platform.
[1]:
https://trustedfirmware-a.readthedocs.io/en/latest/components/cot-binding.html
Change-Id: I2f911206087a1a2942aa728de151d2ac269d27cc
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Trace analysis of FVP_Base_AEMv8A 0.0/6063 model
running in Aarch32 mode with the build options
listed below:
TRUSTED_BOARD_BOOT=1 GENERATE_COT=1
ARM_ROTPK_LOCATION=devel_ecdsa KEY_ALG=ecdsa
ROT_KEY=plat/arm/board/common/rotpk/arm_rotprivk_ecdsa.pem
shows that when auth_signature() gets called
71.99% of CPU execution time is spent in memset() function
written in C using single byte write operations,
see lib\libc\memset.c.
This patch introduces new libc_asm.mk makefile which
replaces C memset() implementation with assembler
version giving the following results:
- for Aarch32 in auth_signature() call memset() CPU time
reduced to 20.56%.
The number of CPU instructions (Inst) executed during
TF-A boot stage before start of BL33 in RELEASE builds
for different versions is presented in the tables below,
where:
- C TF-A: existing TF-A C code;
- C musl: "lightweight code" C "implementation of the
standard library for Linux-based systems"
https://git.musl-libc.org/cgit/musl/tree/src/string/memset.c
- Asm Opt: assemler version from "Arm Optimized Routines"
project
https://github.com/ARM-software/optimized-routines/blob/
master/string/arm/memset.S
- Asm Linux: assembler version from Linux kernel
https://github.com/torvalds/linux/blob/master/arch/arm/lib/memset.S
- Asm TF-A: assembler version from this patch
Aarch32:
+-----------+------+------+--------------+----------+
| Variant | Set | Size | Inst | Ratio |
+-----------+------+------+--------------+----------+
| C TF-A | T32 | 16 | 2122110003 | 1.000000 |
| C musl | T32 | 156 | 1643917668 | 0.774662 |
| Asm Opt | T32 | 84 | 1604810003 | 0.756233 |
| Asm Linux | A32 | 168 | 1566255018 | 0.738065 |
| Asm TF-A | A32 | 160 | 1525865101 | 0.719032 |
+-----------+------+------+--------------+----------+
AArch64:
+-----------+------+------------+----------+
| Variant | Size | Inst | Ratio |
+-----------+------+------------+----------+
| C TF-A | 28 | 2732497518 | 1.000000 |
| C musl | 212 | 1802999999 | 0.659836 |
| Asm TF-A | 140 | 1680260003 | 0.614917 |
+-----------+------+------------+----------+
This patch modifies 'plat\arm\common\arm_common.mk'
by overriding libc.mk makefile with libc_asm.mk and
does not effect other platforms.
Change-Id: Ie89dd0b74ba1079420733a0d76b7366ad0157c2e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
'EHF' is used by RAS, SDEI, SPM_MM common frameworks.
If platform needs to plug-in specific handlers then
'PLAT_EHF_DESC' can be used to populate platform specific
priority levels.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Change-Id: I37af7e0e48111f87b6982604bf5c15db3e05755d
This patch adds support for Event Log generation required
for Measured Boot functionality.
Change-Id: I34f05a33565e6659e78499d62cc6fb00b7d6c2dc
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>
Fixed build error for dualroot chain of trust.
Build error were thrown as below while compiling the code for
dualroot chain of trust:
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.bss.auth_img_flags+0x0): multiple definition of `auth_img_flags';
./build/fvp/debug/bl1/cot.o:(.bss.auth_img_flags+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_size+0x0): multiple definition of `cot_desc_size';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_size+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_ptr+0x0): multiple definition of `cot_desc_ptr';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_ptr+0x0): first defined here
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I1a426c4e7f5f8013d71dafc176c7467c1b329757
CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
Change-Id: If5c35a7517ba00a9f258d7f3e7c8c20cee169a31
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Co-authored-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
When SPD=spmd and SPMD_SPM_AT_SEL2=0, that is SPMC sits at S-EL1
then there is no need for TF-A to load secure partitions individually.
In this configuration, SPMC handles secure partition loading at
S-EL1/EL0 levels.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I06a0d88a4811274a8c347ce57b56bb5f64e345df
Merge the previously introduced arm_fconf_io_storage into arm_io_storage. This
removes the duplicate io_policies and functions definition.
This patch:
- replace arm_io_storage.c with the content of arm_fconf_io_storage.c
- rename the USE_FCONF_BASED_IO option into ARM_IO_IN_DTB.
- use the ARM_IO_IN_DTB option to compile out io_policies moved in dtb.
- propagate DEFINES when parsing dts.
- use ARM_IO_IN_DTB to include or not uuid nodes in fw_config dtb.
- set the ARM_IO_IN_DTB to 0 by default for fvp. This ensure that the behavior
of fvp stays the same as it was before the introduction of fconf.
Change-Id: Ia774a96d1d3a2bccad29f7ce2e2b4c21b26c080e
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
* changes:
plat/arm: Pass cookie argument down to arm_get_rotpk_info()
plat/arm: Add support for dualroot CoT
plat/arm: Provide some PROTK files for development
Use the firmware configuration framework to retrieve information about
Secure Partitions to facilitate loading them into memory.
To load a SP image we need UUID look-up into FIP and the load address
where it needs to be loaded in memory.
This patch introduces a SP populator function which gets UUID and load
address from firmware config device tree and updates its C data
structure.
Change-Id: I17faec41803df9a76712dcc8b67cadb1c9daf8cd
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
