mirror of
https://github.com/u-boot/u-boot.git
synced 2025-04-11 07:24:46 +00:00
c684db989e
Before adding more files, move the bootstd docs into a new directory, with an index. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
193 lines
5.7 KiB
ReStructuredText
193 lines
5.7 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
Milk-V Mars CM
|
|
==============
|
|
|
|
U-Boot for the Milk-V Mars CM uses the same U-Boot binaries as the VisionFive 2
|
|
board. In U-Boot SPL the actual board is detected and the device-tree patched
|
|
accordingly.
|
|
|
|
The Milk-V Mars CM Lite comes without eMMC and needs a different pin muxing
|
|
than the Milk-V Mars CM. The availability and size of the eMMC shows up in the
|
|
serial number displayed by the *mac* command, e.g.
|
|
MARC-V10-2340-D002E016-00000304. The number after the E is the MMC size. U-Boot
|
|
takes a value of E000 as an indicator for the Lite version. Unfortunately the
|
|
vendor has not set this value correctly on some Lite boards.
|
|
|
|
Please, use CONFIG_STARFIVE_NO_EMMC=y if EEPROM data indicates eMMC is present
|
|
on the Milk-V Mars CM Lite. Otherwise you will not be able to read from the
|
|
SD-card.
|
|
|
|
The serial number can be corrected using the *mac* command:
|
|
|
|
.. code-block::
|
|
|
|
mac read_eeprom
|
|
mac product_id MARC-V10-2340-D002E000-00000304
|
|
mac write_eeprom
|
|
|
|
.. note::
|
|
|
|
The *mac initialize* command overwrites the vendor string and the MAC
|
|
addresses. This is why it is avoided here.
|
|
|
|
By default the EEPROM is write protected. The write protection may be overcome
|
|
by connecting the "GND" and "EN" test pads on top of the module.
|
|
|
|
Building
|
|
~~~~~~~~
|
|
|
|
1. Add the RISC-V toolchain to your PATH.
|
|
2. Setup ARCH & cross compilation environment variable:
|
|
|
|
.. code-block:: none
|
|
|
|
export CROSS_COMPILE=<riscv64 toolchain prefix>
|
|
|
|
The M-mode software OpenSBI provides the supervisor binary interface (SBI) and
|
|
is responsible for the switch to S-Mode. It is a prerequisite to build U-Boot.
|
|
Support for the JH7110 was introduced in OpenSBI 1.2. It is recommended to use
|
|
a current release.
|
|
|
|
.. code-block:: console
|
|
|
|
git clone https://github.com/riscv/opensbi.git
|
|
cd opensbi
|
|
make PLATFORM=generic FW_TEXT_START=0x40000000
|
|
|
|
(*FW_TEXT_START* is not needed anymore after OpenSBI patch d4d2582eef7a
|
|
"firmware: remove FW_TEXT_START" which should appear in OpenSBI 1.5.)
|
|
|
|
Now build the U-Boot SPL and U-Boot proper.
|
|
|
|
.. code-block:: console
|
|
|
|
cd <U-Boot-dir>
|
|
make starfive_visionfive2_defconfig
|
|
make OPENSBI=$(opensbi_dir)/build/platform/generic/firmware/fw_dynamic.bin
|
|
|
|
This will generate the U-Boot SPL image (spl/u-boot-spl.bin.normal.out) as well
|
|
as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
|
|
|
|
Device-tree selection
|
|
~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Depending on the board version U-Boot sets variable $fdtfile to either
|
|
starfive/jh7110-milkv-mars-cm.dtb (with eMMC storage) or
|
|
starfive/jh7110-milkv-mars-cm-lite.dtb (without eMMC storage).
|
|
|
|
To overrule this selection the variable can be set manually and saved in the
|
|
environment
|
|
|
|
::
|
|
|
|
env set fdtfile my_device-tree.dtb
|
|
env save
|
|
|
|
or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
|
|
provide a default value.
|
|
|
|
The variable *$fdtfile* is used in the boot process to automatically load
|
|
a device-tree provided by the operating system. For details of the boot
|
|
process refer to the :doc:`/develop/bootstd/index`
|
|
description.
|
|
|
|
Boot source selection
|
|
~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
The low speed connector nRPIBOOT line is used to switch the boot source.
|
|
|
|
* If nRPIBOOT is connected to ground, the board boots from UART.
|
|
* If nRPIBOOT is not connected, the board boots from SPI flash.
|
|
|
|
Compute module boards typically have a switch or jumper for this line.
|
|
|
|
Flashing a new U-Boot version
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
U-Boot SPL is provided as file spl/u-boot-spl.bin.normal.out. Main U-Boot is
|
|
in file u-boot.itb.
|
|
|
|
Assuming your new U-Boot version is on partition 1 of an SD-card you could
|
|
install it to the SPI flash with:
|
|
|
|
::
|
|
|
|
sf probe
|
|
load mmc 0:1 $kernel_addr_r u-boot-spl.bin.normal.out
|
|
sf update $kernel_addr_r 0 $filesize
|
|
load mmc 0:1 $kernel_addr_r u-boot.itb
|
|
sf update $kernel_addr_r 0x100000 $filesize
|
|
|
|
For loading the files from a TFTP server refer to the dhcp and tftpboot
|
|
commands.
|
|
|
|
After updating U-Boot you may want to reboot and reset the environment to the
|
|
default.
|
|
|
|
::
|
|
|
|
env default -f -a
|
|
env save
|
|
|
|
Booting from UART
|
|
~~~~~~~~~~~~~~~~~
|
|
|
|
For booting via UART U-Boot must be built with CONFIG_SPL_YMODEM_SUPPORT=y.
|
|
|
|
With nRPIBOOT connected to ground for UART boot, power the board and upload
|
|
u-boot-spl.bin.normal.out via XMODEM. Then upload u-boot.itb via YMODEM.
|
|
|
|
The XMODEM implementation in the boot ROM is not fully specification compliant.
|
|
It sends too many NAKs in a row. Tio is a terminal emulation that tolerates
|
|
these faults.
|
|
|
|
::
|
|
|
|
$ tio -b 115200 --databits 8 --flow none --stopbits 1 /dev/ttyUSB0
|
|
[08:14:54.700] tio v2.7
|
|
[08:14:54.700] Press ctrl-t q to quit
|
|
[08:14:54.701] Connected
|
|
|
|
(C)StarFive
|
|
CCC
|
|
(C)StarFive
|
|
CCCCCCCC
|
|
|
|
Press *ctrl-t x* to initiate XMODEM-1K transfer.
|
|
|
|
::
|
|
|
|
[08:15:14.778] Send file with XMODEM
|
|
[08:15:22.459] Sending file 'u-boot-spl.bin.normal.out'
|
|
[08:15:22.459] Press any key to abort transfer
|
|
........................................................................
|
|
.......................................................................|
|
|
[08:15:22.459] Done
|
|
|
|
U-Boot SPL 2024.07-rc1-00075-gd6a4ab20097 (Apr 25 2024 - 16:32:10 +0200)
|
|
DDR version: dc2e84f0.
|
|
Trying to boot from UART
|
|
CC
|
|
|
|
Press *ctrl-t y* to initiate YMODEM transfer.
|
|
|
|
::
|
|
|
|
[08:15:50.331] Send file with YMODEM
|
|
[08:15:53.540] Sending file 'u-boot.itb'
|
|
[08:15:53.540] Press any key to abort transfer
|
|
........................................................................
|
|
…
|
|
...............|
|
|
[08:15:53.540] Done
|
|
Loaded 1040599 bytes
|
|
|
|
|
|
U-Boot 2024.07-rc1-00075-gd6a4ab20097 (Apr 25 2024 - 16:32:10 +0200)
|
|
|
|
Booting from SPI flash
|
|
~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
With nRPIBOOT disconnected from ground for SPI boot, power up the board. You
|
|
should see the U-Boot prompt on the serial console.
|