mirror of
https://github.com/u-boot/u-boot.git
synced 2025-04-16 09:54:35 +00:00
f99a1e241f
Use proper binary artifact names for HSFS devices. Do not use the *_unsigned binaries. Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Reviewed-by: Dhruva Gole <d-gole@ti.com>
158 lines
4.2 KiB
ReStructuredText
158 lines
4.2 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
.. sectionauthor:: Wadim Egorov <w.egorov@phytec.de>
|
|
|
|
phyCORE-AM62x
|
|
=============
|
|
|
|
The `phyCORE-AM62x <https://www.phytec.com/product/phycore-am62x>`_ is a
|
|
SoM (System on Module) featuring TI's AM62x SoC. It can be used in combination
|
|
with different carrier boards. This module can come with different sizes and
|
|
models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family.
|
|
|
|
A development Kit, called `phyBOARD-Lyra <https://www.phytec.com/product/phyboard-am62x>`_
|
|
is used as a carrier board reference design around the AM62x SoM.
|
|
|
|
Quickstart
|
|
----------
|
|
|
|
* Download sources and TI firmware blobs
|
|
* Build Trusted Firmware-A
|
|
* Build OP-TEE
|
|
* Build U-Boot for the R5
|
|
* Build U-Boot for the A53
|
|
* Create bootable uSD Card
|
|
* Boot
|
|
|
|
Sources
|
|
-------
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_boot_sources
|
|
:end-before: .. k3_rst_include_end_boot_sources
|
|
|
|
Build procedure
|
|
---------------
|
|
|
|
Setup the environment variables:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_common_env_vars_desc
|
|
:end-before: .. k3_rst_include_end_common_env_vars_desc
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_board_env_vars_desc
|
|
:end-before: .. k3_rst_include_end_board_env_vars_desc
|
|
|
|
Set the variables corresponding to this platform:
|
|
|
|
.. include:: ../ti/k3.rst
|
|
:start-after: .. k3_rst_include_start_common_env_vars_defn
|
|
:end-before: .. k3_rst_include_end_common_env_vars_defn
|
|
.. code-block:: bash
|
|
|
|
$ export UBOOT_CFG_CORTEXR=phycore_am62x_r5_defconfig
|
|
$ export UBOOT_CFG_CORTEXA=phycore_am62x_a53_defconfig
|
|
$ export TFA_BOARD=lite
|
|
$ # we don't use any extra TFA parameters
|
|
$ unset TFA_EXTRA_ARGS
|
|
$ export OPTEE_PLATFORM=k3-am62x
|
|
$ export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y"
|
|
|
|
.. include:: ../ti/am62x_sk.rst
|
|
:start-after: .. am62x_evm_rst_include_start_build_steps
|
|
:end-before: .. am62x_evm_rst_include_end_build_steps
|
|
|
|
uSD Card creation
|
|
-----------------
|
|
|
|
Use fdisk to partition the uSD card. The layout should look similar to:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ sudo fdisk -l /dev/mmcblk0
|
|
Disk /dev/mmcblk0: 7.56 GiB, 8120172544 bytes, 15859712 sectors
|
|
Units: sectors of 1 * 512 = 512 bytes
|
|
Sector size (logical/physical): 512 bytes / 512 bytes
|
|
I/O size (minimum/optimal): 512 bytes / 512 bytes
|
|
Disklabel type: dos
|
|
Disk identifier: 0x6583d9a3
|
|
|
|
Device Boot Start End Sectors Size Id Type
|
|
/dev/mmcblk0p1 * 2048 264191 262144 128M c W95 FAT32 (LBA)
|
|
/dev/mmcblk0p2 264192 1934953 1670762 815.8M 83 Linux
|
|
|
|
|
|
Once partitioned, the boot partition has to be formatted with a FAT filesystem.
|
|
Assuming the uSD card is `/dev/mmcblk0`:
|
|
|
|
.. code-block:: bash
|
|
|
|
$ mkfs.vfat /dev/mmcblk0p1
|
|
|
|
To boot from a micro SD card on a HSFS device simply copy the following
|
|
artifacts to the FAT partition:
|
|
|
|
* tiboot3.bin from R5 build
|
|
* tispl.bin from Cortex-A build
|
|
* u-boot.img from Cortex-A build
|
|
|
|
Boot
|
|
----
|
|
|
|
Put the uSD card in the slot on the board and apply power. Check the serial
|
|
console for output.
|
|
|
|
Flash to SPI NOR
|
|
----------------
|
|
|
|
Below commands can be used to flash the SPI NOR flash; assuming
|
|
tiboot3.bin, tispl.bin and u-boot.img are stored on the uSD card.
|
|
|
|
.. code-block:: bash
|
|
|
|
sf probe
|
|
fatload mmc 1 ${loadaddr} tiboot3.bin
|
|
sf update $loadaddr 0x0 $filesize
|
|
fatload mmc 1 ${loadaddr} tispl.bin
|
|
sf update $loadaddr 0x80000 $filesize
|
|
fatload mmc 1 ${loadaddr} u-boot.img
|
|
sf update $loadaddr 0x280000 $filesize
|
|
|
|
|
|
Boot Modes
|
|
----------
|
|
|
|
The phyCORE-AM62x development kit supports booting from many different
|
|
interfaces. By default, the development kit is set to boot from the micro-SD
|
|
card. To change the boot device, DIP switches S5 and S6 can be used.
|
|
Boot switches should be changed with power off.
|
|
|
|
.. list-table:: Boot Modes
|
|
:widths: 16 16 16
|
|
:header-rows: 1
|
|
|
|
* - Switch Label
|
|
- SW5: 12345678
|
|
- SW6: 12345678
|
|
|
|
* - uSD
|
|
- 11000010
|
|
- 01000000
|
|
|
|
* - eMMC
|
|
- 11010010
|
|
- 00000000
|
|
|
|
* - OSPI
|
|
- 11010000
|
|
- 10000000
|
|
|
|
* - UART
|
|
- 11011100
|
|
- 00000000
|
|
|
|
Further Information
|
|
-------------------
|
|
|
|
Please see :doc:`../ti/am62x_sk` chapter for further AM62 SoC related documentation
|
|
and https://docs.phytec.com/phycore-am62x for vendor documentation.
|