mirror of
https://github.com/u-boot/u-boot.git
synced 2025-04-17 02:15:02 +00:00
1e21f56930
When RK3328 boards run SPL from eMMC and fail to load FIT from eMMC due to it being missing or checksum validation fails there is a fallback to read FIT from SD-card. However, without proper pinctrl configuration reading FIT from SD-card will fail: U-Boot SPL 2024.04-rc1 (Feb 05 2024 - 22:18:22 +0000) Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error Trying to boot from MMC2 Card did not respond to voltage select! : -110 spl: mmc init failed with error: -95 Trying to boot from MMC1 mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph props. Also sort and move common nodes shared by all boards to the SoC u-boot.dtsi. Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
50 lines
1.1 KiB
Text
50 lines
1.1 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2016-2019 Rockchip Electronics Co., Ltd
|
|
*/
|
|
|
|
#include "rk3328-u-boot.dtsi"
|
|
#include "rk3328-sdram-ddr3-666.dtsi"
|
|
|
|
/{
|
|
gmac_clkin: external-gmac-clock {
|
|
compatible = "fixed-clock";
|
|
clock-frequency = <125000000>;
|
|
clock-output-names = "gmac_clkin";
|
|
#clock-cells = <0>;
|
|
};
|
|
|
|
vcc5v0_host_xhci: vcc5v0-host-xhci-drv {
|
|
compatible = "regulator-fixed";
|
|
enable-active-high;
|
|
gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
|
regulator-name = "vcc5v0_host_xhci";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
};
|
|
};
|
|
|
|
&gmac2io {
|
|
phy-supply = <&vcc_phy>;
|
|
phy-mode = "rgmii";
|
|
clock_in_out = "input";
|
|
snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
|
|
snps,reset-active-low;
|
|
snps,reset-delays-us = <0 10000 50000>;
|
|
assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
|
|
assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmiim1_pins>;
|
|
tx_delay = <0x26>;
|
|
rx_delay = <0x11>;
|
|
status = "okay";
|
|
};
|
|
|
|
&gmac2phy {
|
|
/* Integrated PHY unsupported by U-Boot */
|
|
status = "broken";
|
|
};
|
|
|
|
&vcc_sd {
|
|
bootph-pre-ram;
|
|
};
|