mirror of
https://github.com/u-boot/u-boot.git
synced 2025-04-18 02:44:37 +00:00
208fc7a9f9
Tim Harvey <tharvey@gateworks.com> says: Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC specification described as: Boot Area Partition 1 Boot Area Partition 2 RPMB Partition General Purpose Partition 1 General Purpose Partition 2 General Purpose Partition 3 General Purpose Partition 4 User Data Area These are referenced by fields in the PARTITION_CONFIG register (Extended CSD Register 179) which is defined as: bit 7: reserved bit 6: BOOT_ACK 0x0: No boot acknowledge sent (default 0x1: Boot acknowledge sent during boot operation Bit bit 5:3: BOOT_PARTITION_ENABLE 0x0: Device not boot enabled (default) 0x1: Boot Area partition 1 enabled for boot 0x2: Boot Area partition 2 enabled for boot 0x3-0x6: Reserved 0x7: User area enabled for boot bit 2:0 PARTITION_ACCESS 0x0: No access to boot partition (default) 0x1: Boot Area partition 1 0x2: Boot Area partition 2 0x3: Replay Protected Memory Block (RPMB) 0x4: Access to General Purpose partition 1 0x5: Access to General Purpose partition 2 0x6: Access to General Purpose partition 3 0x7: Access to General Purpose partition 4 Note that setting PARTITION_ACCESS to 0x0 results in selecting the User Data Area partition. You can see above that the two fields BOOT_PARTITION_ENABLE and PARTITION_ACCESS do not use the same enumerated values. U-Boot uses a set of macros to access fields of the PARTITION_CONFIG register: EXT_CSD_BOOT_ACK_ENABLE (1 << 6) EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3) EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0) EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0) EXT_CSD_BOOT_ACK(x) (x << 6) EXT_CSD_BOOT_PART_NUM(x) (x << 3) EXT_CSD_PARTITION_ACCESS(x) (x << 0) EXT_CSD_EXTRACT_BOOT_ACK(x) (((x) >> 6) & 0x1) EXT_CSD_EXTRACT_BOOT_PART(x) (((x) >> 3) & 0x7) EXT_CSD_EXTRACT_PARTITION_ACCESS(x) ((x) & 0x7) There are various places in U-Boot where the BOOT_PARTITION_ENABLE field is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a hardware partition consistent with the definition of the PARTITION_ACCESS field used by the various mmc_switch incarnations. To add some sanity to the distinction between BOOT_PARTITION_ENABLE (used to specify the active device on power-cycle) and PARTITION_ACCESS (used to switch between hardware partitions) create two enumerated types and use them wherever struct mmc * part_config is used or the above macros are used. Additionally provide arrays of the field names and allow those to be used in the 'mmc partconf' command and in board support files. The first patch adds enumerated types and makes use of them which represents no compiled code change. The 2nd patch adds the array of names and uses them in the 'mmc partconf' command. The 3rd patch uses the array of hardware partition names in a board support file to show what emmc hardware partition U-Boot is being loaded from. |
||
|---|---|---|
| .. | ||
| eeprom.c | ||
| eeprom.h | ||
| imximage-8mm-lpddr4.cfg | ||
| imximage-8mn-lpddr4.cfg | ||
| imximage-8mp-lpddr4.cfg | ||
| Kconfig | ||
| lpddr4_timing.h | ||
| lpddr4_timing_imx8mm.c | ||
| lpddr4_timing_imx8mn.c | ||
| lpddr4_timing_imx8mp.c | ||
| MAINTAINERS | ||
| Makefile | ||
| spl.c | ||
| venice.c | ||
| venice.env | ||