mirror of
https://github.com/u-boot/u-boot.git
synced 2025-04-16 01:44:34 +00:00
752c376987
This fixture name is quite long and results in lots of verbose code. We know this is U-Boot so the 'u_boot_' part is not necessary. But it is also a bit of a misnomer, since it provides access to all the information available to tests. It is not just the console. It would be too confusing to use con as it would be confused with config and it is probably too short. So shorten it to 'ubman'. Signed-off-by: Simon Glass <sjg@chromium.org> Link: https://lore.kernel.org/u-boot/CAFLszTgPa4aT_J9h9pqeTtLCVn4x2JvLWRcWRD8NaN3uoSAtyA@mail.gmail.com/
79 lines
2.9 KiB
Python
79 lines
2.9 KiB
Python
# SPDX-License-Identifier: GPL-2.0
|
|
# (C) Copyright 2023, Advanced Micro Devices, Inc.
|
|
|
|
import pytest
|
|
import re
|
|
|
|
"""
|
|
Note: This test relies on boardenv_* containing configuration values to define
|
|
the PHY device info including the device name, address, register address/value
|
|
and write data value. This test will be automatically skipped without this.
|
|
|
|
For example:
|
|
|
|
# Setup env__mdio_util_test to set the PHY address, device names, register
|
|
# address, register address value, and write data value to test mdio commands.
|
|
# Test will be skipped if env_mdio_util_test is not set
|
|
env__mdio_util_test = {
|
|
"eth0": {"phy_addr": 0xc, "device_name": "TI DP83867", "reg": 0,
|
|
"reg_val": 0x1000, "write_val": 0x100},
|
|
"eth1": {"phy_addr": 0xa0, "device_name": "TI DP83867", "reg": 1,
|
|
"reg_val": 0x2000, "write_val": 0x100},
|
|
}
|
|
"""
|
|
|
|
def get_mdio_test_env(ubman):
|
|
f = ubman.config.env.get("env__mdio_util_test", None)
|
|
if not f or len(f) == 0:
|
|
pytest.skip("No PHY device to test!")
|
|
else:
|
|
return f
|
|
|
|
@pytest.mark.buildconfigspec("cmd_mii")
|
|
@pytest.mark.buildconfigspec("phylib")
|
|
def test_mdio_list(ubman):
|
|
f = get_mdio_test_env(ubman)
|
|
output = ubman.run_command("mdio list")
|
|
for dev, val in f.items():
|
|
phy_addr = val.get("phy_addr")
|
|
dev_name = val.get("device_name")
|
|
|
|
assert f"{phy_addr:x} -" in output
|
|
assert dev_name in output
|
|
|
|
@pytest.mark.buildconfigspec("cmd_mii")
|
|
@pytest.mark.buildconfigspec("phylib")
|
|
def test_mdio_read(ubman):
|
|
f = get_mdio_test_env(ubman)
|
|
output = ubman.run_command("mdio list")
|
|
for dev, val in f.items():
|
|
phy_addr = hex(val.get("phy_addr"))
|
|
dev_name = val.get("device_name")
|
|
reg = hex(val.get("reg"))
|
|
reg_val = hex(val.get("reg_val"))
|
|
|
|
output = ubman.run_command(f"mdio read {phy_addr} {reg}")
|
|
assert f"PHY at address {int(phy_addr, 16):x}:" in output
|
|
assert f"{int(reg, 16):x} - {reg_val}" in output
|
|
|
|
@pytest.mark.buildconfigspec("cmd_mii")
|
|
@pytest.mark.buildconfigspec("phylib")
|
|
def test_mdio_write(ubman):
|
|
f = get_mdio_test_env(ubman)
|
|
output = ubman.run_command("mdio list")
|
|
for dev, val in f.items():
|
|
phy_addr = hex(val.get("phy_addr"))
|
|
dev_name = val.get("device_name")
|
|
reg = hex(val.get("reg"))
|
|
reg_val = hex(val.get("reg_val"))
|
|
wr_val = hex(val.get("write_val"))
|
|
|
|
ubman.run_command(f"mdio write {phy_addr} {reg} {wr_val}")
|
|
output = ubman.run_command(f"mdio read {phy_addr} {reg}")
|
|
assert f"PHY at address {int(phy_addr, 16):x}:" in output
|
|
assert f"{int(reg, 16):x} - {wr_val}" in output
|
|
|
|
ubman.run_command(f"mdio write {phy_addr} {reg} {reg_val}")
|
|
output = ubman.run_command(f"mdio read {phy_addr} {reg}")
|
|
assert f"PHY at address {int(phy_addr, 16):x}:" in output
|
|
assert f"{int(reg, 16):x} - {reg_val}" in output
|