Update and improve the building documentation of Apalis iMX8.
The following changes were made:
- imx-atf repository changed to nxp-imx GitHub.
- imx-atf branch updated to 'lf_v2.6'.
- imx-seco updated to version 5.8.7.
- nxp-imx mfgtools link updated to GitHub releases.
- General writing improvements.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Update and improve the building documentation of Colibri iMX8X.
The following changes were made:
- imx-atf repository changed to nxp-imx GitHub.
- imx-atf branch updated to 'lf_v2.6'.
- imx-seco updated to version 5.8.7.
- nxp-imx mfgtools link updated to GitHub releases.
- General writing improvements.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
- A new driver in the misc to register setting from device tree. This
also provides user a clean interface and all register settings are
centralized in one place, device tree.
- Enable Agilex5 platform for Intel product. Changes, modification and
new files are created for board, dts, configs and makefile to create
the base for Agilex5.
Build-tested on SoC64 boards, boot tested on some of them.
Please pull the updates for rockchip platform:
- Add board: rk3588 Generic, Cool Pi CM5, Theobroma-Systems RK3588 Jaguar SBC,
Toybrick TB-RK3588X;
rk3588s Cool Pi 4B;
rk3566 Pine64 PineTab2;
- Add saradc v2 support;
- Add PMIC RK806 support;
- rk3588 disable force_jtag by default;
- Migrate to use IO-domain driver for all boards;
- Use common bss and stack addresses for rk33xx and rk35xx boards;
- Other updates for driver, config and dts;
Add support to the RGxx3 device for the Powkiddy RGB10MAX3. This device
is extremely similar to all the other devices and can use the same
bootloader with the same detection logic.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 PineTab2 is a tablet computer based on the Rockchip RK3566
SoC. The table features 4/8 GB LPDDR4 RAM and 64/128 GB eMMC storage.
Features tested on a Pine64 PineTab2 8GB v2.0:
- SD-card boot
- eMMC boot
- SPI Flash boot
- USB host
Device tree is imported from linux maintainer branch v6.9-armsoc/dts64,
commit 1b7e19448f8f ("arm64: dts: rockchip: Add devicetree for Pine64
PineTab2").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3588S/RK3588 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3588S/RK3588 boards that follow reference board design.
Also fix the alphabetical order of RK3588 boards listed in Makefile and
documentation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
TB-RK3588X board is a Rockchip Toybrick RK3588 based development board.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
8/16GB Memory LPDDR4x
Mali G610MC4 GPU
2× MIPI-CSI0 Connector
1x 2Lanes PCIe3.0 Connector
1x SATA3.0 Connector
32GB eMMC Module
2x USB 2.0, 2x USB 3.0
1x HDMI Output, 1x HDMI Input
2x Ethernet Port
Functions work normally:
[1] USB2.0 Host
[2] Ethernet0 with PHY RTL8211F
More information can be obtained from the following websites:
[1] https://t.rock-chips.com/en/wiki/EN/tb-rk3588x_en/index.html
[2] http://t.rock-chips.com/
Kernel commits:
8ffe365f8dc7 ("arm64: dts: rockchip: Add devicetree support for TB-RK3588X board")
7140387ff49d ("dt-bindings: arm: rockchip: Add Toybrick TB-RK3588X")
Reviewed-by: Weizhao Ouyang <weizhao.ouyang@arm.com>
Signed-off-by: Elon Zhang <zhangzj@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-orangepi-r1-plus boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Add PHY_ROCKCHIP_INNO_USB2=y option to support the onboard USB PHY.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-nanopi-r2* boards with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_GIGE=y, PHY_MOTORCOMM=y, PHY_REALTEK=y and remove
&gmac2io to support reset of onboard ethernet PHYs. Also add DM_MDIO=y
to ensure device tree props is used by motorcomm PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add DM_REGULATOR_GPIO=y and SPL_DM_REGULATOR_GPIO=y to support the
regulator-gpio compatible.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree files to MAINTAINERS file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-rock-pi-e with new defaults.
Remove the xPL_DRIVERS_MISC=y option, no misc driver is used in xPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_MDIO=y to ensure device tree props can be used by PHY driver.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add myself as a reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3328-roc-cc with new defaults.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM. Also add LEGACY_IMAGE_FORMAT=y to keep
support for scripts.
Remove SPL_I2C=y and SPL_PMIC_RK8XX=y, the related i2c and pmic nodes is
not included in the SPL fdt.
Add CMD_GPIO=y and CMD_REGULATOR=y to add the helpful gpio and regulator
commands. Also add CMD_POWEROFF=y to be able to use the poweroff command.
Add ROCKCHIP_EFUSE=y and remove NET_RANDOM_ETHADDR=y, ethaddr and
eth1addr is set based on cpuid read from eFUSE.
Add SPL_DM_SEQ_ALIAS=y option to use alias sequence number in SPL.
Add DM_ETH_PHY=y, PHY_MOTORCOMM=y and PHY_REALTEK=y to support common
ethernet PHYs.
Remove REGULATOR_PWM=y, the pwm-regulator compatible is not used.
Add RNG_ROCKCHIP=y and DM_RNG=y options to support the onboard random
generator.
Also add missing device tree file to MAINTAINERS and add myself as a
reviewer for this board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This migrates the plaintext README in
board/theobroma-systems/ringneck_px30 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
This migrates the plaintext README in
board/theobroma-systems/puma_rk3399 to doc/board/theobroma-systems and
while doing so, update the instructions and rewrite it in rST.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Use proper binary artifact names for HSFS devices.
Do not use the *_unsigned binaries.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
TI K3 J784S4 and AM69 are new additions to the K3 SoC family.
Add documentation about the J784S4 EVM and AM69 SK.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # AM69-SK
Use the latest, mx93a1-ahab-container.img that is compatible with the
i.MX93 A1 revision.
Using mx93a1-ahab-container.img on an A0 chip and conversely causes a boot
failure without any traces on the UART.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
The MSM8916/APQ8016 Technical Reference Manual is publicly available and
contains a lot of useful register maps for many core parts of the SoC.
Include an archive.org link to it in the dragonboard410c documentation.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Replace the board specific docs with a generic board.rst file which
documents the build/boot process for the sdm845 and qcs404 boards now
that the only differences are the DTB in use.
At the same time, create a debugging page to document some useful
snippets and tips for working with Qualcomm platforms.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add document for Milk-V Duo board which based on Sophgo's CV1800B SoC.
Signed-off-by: Kongyang Liu <seashell11234455@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support for WinLink E850-96 board [1]. It's based on Exynos850 SoC
and follows 96boards specification, so it's compatible with 96boards
mezzanine boards [2]. This patch enables next features:
* Serial console
* USI
* PMU (muxing AP UART path)
* Pinctrl
* Clocks
* Timer (ARMv8 architected)
* Reset control
It's quite a minimal enablement. Features like MMC, USB and Ethernet
will be enabled later.
The rationale for config values is as follows:
* TEXT_BASE = 0xf8800000
That's where BL2 loads the U-Boot payload, so TEXT_BASE must be
exactly this value. Overall the memory map is designed in a way to
keep the bootloader in the upper 128 MiB area of RAM, which is
0xf8000000..0xffffffff. That includes bootloader's code, stack,
data, heap, MMU tables, etc. All the memory below that 128 MiB chunk
can be used for storing boot images (0x80000000..0xf8000000).
* CUSTOM_SYS_INIT_SP_ADDR = 0xf8c00000
Just 4 MiB above the TEXT_BASE address, to leave enough space for
U-Boot code and stack itself (grows downwards).
* SYS_LOAD_ADDR = 0x80000000
The beginning of RAM. That's where Linux kernel image must be
loaded.
* SYS_MALLOC_LEN = 0x81f000
8 MiB for malloc() + ENV_SIZE (128 KiB)
* SYS_MALLOC_F_LEN = 0x4000
Increase malloc() pool size available before relocation from 8 KiB
(default) to 16 KiB. Otherwise "alloc space exhausted" message
appears in U-Boot log during board_init_f() stage. There are next
reasons for doing so:
1. Having "bootph-all" flags in some dts nodes leads to binding
those during pre-relocation stage, and binding (DM) uses
dynamic memory allocation
2. clk-exynos850 driver uses CCF clocks, which in turn use dynamic
memory allocation
Device tree file was imported from Linux kernel. All nodes and boot
phase flags added in exynos850-e850-96-u-boot.dtsi are only needed to
enable serial console:
* oscclk -> cmu_top -> cmu_peri: generate UART/USI clocks
* pinctrl_alive and uart1_pins: needed to mux UART pins
* pmu_system_controller: configures AP UART path to uart1_pins
* usi_uart: configures USI block to operate as a UART protocol
* serial_0: enables serial console (UART)
[1] https://www.96boards.org/product/e850-96b/
[2] https://www.96boards.org/products/mezzanine/
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update the RGxx3 documentation to note that it now supports the
RG-ARC-D, RG-ARC-S, Powkiddy RK2023, and Powkiddy RGB30. Also update
verbiage around panel detection to note that it is no longer hard coded
to the RG503.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With latest coreboot (e.g.: v4.22.01), the instructions to enable
graphics support has changed. Refresh the doc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add brief documentation on how to build a bootable U-Boot image for the
phyGATE-Tauri-L.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Adjust the underline length so that it matches the title length.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Provide a configuration fragment to enable ACPI on QEMU.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
This commit adds a general flow to explain the usage of firewalls and
the chain of trust in K3 devices.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Recently, the U-Boot installation process has changed significantly.
This should be depicted in documentation.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Mention TI_DM argument can be used to fetch a custom DM binary in the
A72 build instructions for K3 devices.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
The mtd_debug write does not work in this context. The flashcp command does
work, provides both the erase and write functions and with the verbose
option gives good feedback.
Signed-off-by: Stephen Graf <stephen.graf@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
