Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> says:
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
Enable the SPI_ADVANCE config option for all xilinx platforms, as
this is required for parallel-memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Enable setting speed mode using mmc dev commands.
The speed mode is provided as the last argument in these commands
(ex: mmc dev 0 0 10) and is indicated using the index from enum
bus_mode in include/mmc.h. A speed mode can be set if it is enabled
from device tree or from capabilities register
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240708091755.5021-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Boards which have for example MAC address in eeprom but not in Xilinx
format (legacy or FRU) could reference it via nvmem cells.
For example:
&gem0 {
nvmem-cells = <&mac>;
nvmem-cell-names = "mac-address";
};
&eeprom {
#address-cells = <1>;
#size-cells = <1>;
mac: mac-address@f0 {
reg = <0xf0 6>;
};
};
For getting it work above DT changes are required but also CONFIG_NVMEM
should be enabled. That's why enable it by default in generic defconfigs
to be able to use it directly by changing DT only.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9c8ee7a4c7a16367438a92a4c9581bac9d968f84.1712815454.git.michal.simek@amd.com
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabled the default utilization of the NFS command across all Xilinx
platforms to facilitate the booting of images through the network
using the NFS protocol.
Fixes: 10de125707 ("disable NFS support by default")
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20240104045217.2966454-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env
variables is overwriting data at 0 offset, which is wrong. So add default
redund env offset for Zynq, ZynqMP, Versal and microblaze platforms.
Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE).
In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead
of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000.
Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of
ENV_IS_IN_SPI_FLASH config.
Below table specifies platform specific env and env redund offsets.
PLAT ENV_OFFSET ENV_OFFSET_REDUND
---- ---------- -----------------
ZYNQ 0xE0000 0xE40000
ZYNQMP 0x1E00000 0x1E80000
VERSAL 0x7F40000 0x7F00000
MICROBLAZE 0x1080000 0x10C0000
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com
Zynq can use efi capsule infrastructure that's why enable it by default.
For capsule generation for zynq you can use:
pushd spl
../tools/mkeficapsule -g "1ba29a15-9969-40aa-b424-e86121618664" boot.bin \
--index 1 ../capsule1.bin
popd
./tools/mkeficapsule -g "1a5178f0-87d3-4f36-ac63-3b31a23be305" u-boot.img \
--index 2 capsule2.bin
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a8194ecfa7932f2d8ada5ee508b2a026c782f15e.1660055571.git.michal.simek@amd.com
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
