Some of Kconfigs are using utf-8 encoding because of used chars. Convert
all of them to ascii enconging. Based on discussion ASCII should be used in
general with the exception of names.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_mdp_ready() handles status polling for multi-die package parts that
requires to read and check status register for each die. To support
S28HS02GT(dual-die package with Octal DTR support), rename function and
use nor->rdsr_dummy in octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
During SFDP header parse and BFPT parse, structures in stack are used
to perform spi_nor_read_sfdp() which expects a dma-safe buffer.
This commit introduces spi_nor_read_sfdp_dma_unsafe() to wrap
spi_nor_read_sfdp() using a kmalloc'ed bounce buffer which is
the same implementation in Linux (drivers/mtd/spi-nor/sfdp.c).
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
MT25QU01 OPN with 4B OPCODE support is currently not supported in
source code and the driver reuses the definition for "n25q00a"
which has the same silicon ID but is a slower part.
Adding mt25u01g definition to the source code to support a faster
read response for MT25QU01 QSPI NOR Flash device.
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
[jagan: fix the id position and commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Support for GigaDevice GD55LB02GEBIR SPI NOR flash as QSPI
configuration flash
Signed-off-by: Teik Heng Chong <teik.heng.chong@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip,
as used on the Xunlong Orange Pi Zero 3 board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Compiling sandbox_defconfig with CONFIG_BOOTSTD=n fails:
/usr/bin/ld: drivers/mtd/spi/sf_bootdev.o:
in function `sf_get_bootflow':
/drivers/mtd/spi/sf_bootdev.c:43:(.text+0x96):
undefined reference to `bootmeth_set_bootflow'
Add the missing Kconfig dependency.
Fixes: Fixes: 0c1f4a9fb1 ("bootstd: Add a SPI flash bootdev")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
Add support for XMC XM25QU128C (128M-bit) Serial Flash memory. Used on
the Xunlong Orange Pi 3B, 5 and 5 Plus boards.
Datasheet:
https://www.xmcwh.com/uploads/806/XM25QU128C_Ver2.0.pdf
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
[jonas@kwiboo.se: update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for Winbond 256M-bit flash w25q256jwm.
Performed basic erase/write/readback operations on
ZynqMP zc1751+dc1 board.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
XTX changed full company name from "XTX Technology (Shenzhen) Limited
to "XTX Technology Limited" since 2020,So remove "(Shenzhen)".
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The 'tiny' SPI nor functions have the same name as their big brothers,
which can be confusing. Use different names so it is clear which
version is in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With tiny SPI flash the erasesize is 0 which can cause a divide-by-zero
error. Check for this and return a proper error instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds fixups for s25fs512s to address the following issues
from reading SFDP:
- Non-uniform sectors by factory default. The setting needs to be
checked and assign erase hook as needed.
- Page size is wrongly advertised in SFDP.
- READ_1_1_2 (3Bh/3Ch), READ_1_1_4 (6Bh/6Ch), and PP_1_1_4 (32h/34h)
are not supported.
- Bank Address Register (BAR) is not supported.
In addition, volatile version of Quad Enable is used for safety.
Based on patch by Takahiro Kuwano with s25fs_s_post_bfpt_fixup() updated
to use 4-byte address commands instead of extended address mode and the
page_size is fixed to 256
For future use, manufacturer code should be moved out from framework
code as same as in Linux.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a missing fallthrough macro to avoid a -Wimplicit-fallthrough warning.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for CHIP_ERASE opcode 0xc7 . This is useful in case the
entire SPI NOR is supposed to be erase at once, as is it considerably
faster than 4k sector erase and even slightly faster than 64k block
erase. The spi_nor_erase_chip() implementation is adapted from Linux
6.1.y as of commit 7d54cb2c26dad ("Linux 6.1.14") . The chip erase is
only used in case the entire MTD device is being erased, and the chip
does support this functionality.
Timing figures from W25Q128JW:
16 MiB erase using 4kiB sector erase opcode 0x20 ... 107.5s
16 MiB erase using 64kiB block erase opcode 0xd8 ... 39.1s
16 MiB erase using chip erase opcode 0xc7 .......... 38.7s
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
Infineon S25FS256T is 256Mbit Quad SPI NOR flash. The key features and
differences comparing to other Spansion/Cypress flash familes are:
- 4-byte address mode by factory default
- Quad mode is enabled by factory default
- Supports mixture of 128KB and 64KB sectors by OTP configuration
(this patch supports uniform 128KB only)
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rename s25hx_t prefix to s25 so that the single set of fixup hooks can
support all other S25 families.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Acked-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We need extensions to be set up before we start trying to boot any of the
bootdevs. Add a new priority before all the others for tht sort of thing.
Also add a 'none' option, so that the first one is not 0.
While we are here, comment enum bootdev_prio_t fully and expand the test
for the 'bootdev hunt' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
flash_is_locked is changed to flash_is_unlocked with commit 513c6071ce
("mtd: spi: Convert is_locked callback to is_unlocked"). sst26_is_locked()
is also changed to sst26_is_unlocked() but the logic remained same.
Invert the logic for the flash lock/unlock to work properly.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221122051833.13306-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
