k3_avs driver checks opp_ids when probing and overwrites the voltage
values in vd_data for the respective board. The new k3_avs_check_opp()
can be called from board files to check the efuse data and returns 0 if
valid.
Also add the same check in k3_avs_program_voltage() to error out if
the efuse data was not valid.
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance
Points as per (7.5 Operating Performance Points) section in the
Datasheet [0].
- A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM.
- A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW
voltage (though OPP_LOW voltage is recommended to reduce power
consumption).
Add OPP_LOW frequency->voltage entry to vd_data.
The actual OPP voltage for the device is read from the efuse and
updated in k3_avs_probe().
OPP_NOM corresponds to OPP_1 and OPP_LOW to OPP_0 efuse register
fields, as described in the Datasheet [0]
The register offsets and fields are described in the TRM (5.2.6.1.5
WKUP_VTM_VD_OPPVID_j Register) [1].
[0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet)
[1]: https://www.ti.com/lit/pdf/spruiu1 (J7200 TRM)
Signed-off-by: Reid Tonking <reidt@ti.com>
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Different devices have different MPU clk and dev ID. Currently it had
been hardcoded. Move it to DT based extraction.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Check if AVS could not be programmed and print a warning.
Fixes: 9d233b4e3e ("misc: k3_avs: add driver for K3 Adaptive Voltage Scaling Class 0")
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.
Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>
The ti,j7200-vtm and ti,j721e-vtm compatibles are used for voltage
and thermal monitoring (VTM) by (drivers/thermal/k3_j72xx_bandgap.c)
in Linux, but the same hardware is used for adaptive voltage scaling
(AVS) in u-boot, This brings both drivers in line with the same
compatibles.
Since the j7200 uses the config as the j721e, the data is inherited
from j721e vs creating a duplicate
Signed-off-by: Neha Francis <n-francis@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
The latest data manual SPRSP08I –NOVEMBER 2017–REVISED DECEMBER 2019[1]
for am65xx SoC states the new MPU nominal voltages to be 1.1V (OPP_NOM),
1.2V (OPP_OD) and 1.24V (OPP_TURBO). Update the nominal voltages in the
K3 AVS driver to reflect this.
[1] http://www.ti.com/lit/gpn/am6528
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Its possible that k3_avs_priv is NULL because the driver may not have
been probed yet. Therefore check if pointer is valid before
dereferencing it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
j721e SoCs have different OPP tables. Add support for the same.
Note: DM Still has lot of voltages TBD hence the correct
values need to be programmed once they are published.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Adaptive Voltage Scaling is a technology used in TI SoCs to optimize
the operating voltage based on characterization data written to efuse
during production. Add a driver to support this feature for K3 line of
SoCs, initially for AM65x.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
