The phycore-rk3288 can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for rockchip vendor prefix accordingly.
Move device tree nodes required for u-boot to rk3288-phycore-rdk-u-boot.dtsi
such as chosen, i2c_eeprom_id and it's alias.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am62x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Caleb Connolly <caleb.connolly@linaro.org> says:
This is a subset of [1]. With more platform maintainers switching to
OF_UPSTREAM I didn't want to get in the way (it has also proven more
difficult than I hoped to remove only the fully compatible header
files).
This series removes only the dt-bindings headers which contain generic
data like GPIO flags, input event codes, etc.
It then implements support for building all DTBs for a vendor with
OF_UPSTREAM_BUILD_VENDOR. This removes the need to maintain a set list
of DTBs that can be built by U-Boot and opens up the possibility of new
boards becoming supported "by default" just by landing their DT
upstream.
[1]: https://lore.kernel.org/u-boot/20240321-b4-upstream-dt-headers-v2-0-1eac0df875fe@linaro.org
MD Danish Anwar <danishanwar@ti.com> says:
The series introduces device tree and config changes and AM65x
to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
for AM65x in order to load overlay over spl.
The ICSSG2 node is added in device tree overlay so that it remains in
sync with linux kernel.
This series has been tested on AM65x SR2.0, and the ICSSG interface is
able to ping / dhcp and boot kernel using tftp in uboot.
The users need to set env variables fw_storage_interface, fw_dev_part,
fw_ubi_mtdpart, fw_ubi_volume to indicate which storage medium and
partition they want to use to load firmware files from. By default the env
fw_storage_interface=mmc and fw_dev_part=1:2 but users can modify these
envs as per their requirements.
Add ICSSG2 overlay and configuration to tispl and u-boot images.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
In Linux, we allow sleep moci to be turned off when the carrier board
supports it and the system is in suspend. In U-Boot, however, we want
the sleep moci to be always on. So we use a gpio hog and disable the
regulator. This change is necessary because we switched to upstream
device tree files with commit c07bba7a2c ("verdin-am62: move verdin
am62 to OF_UPSTREAM"). A recent upstream patch removes the gpio hog from
the Linux device tree, so we need to add it to the u-boot dtsi. The
following patch will remove the gpio hog from the Linux device tree:
https://lore.kernel.org/linux-devicetree/20240301084901.16656-1-eichest@gmail.com/
The U-Boot patch can be applied without it and will not break the build.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Adds tifsstub binaries, this is required for deepsleep functionality.
This implements the same change as commit 128f81290b ("arm: dts: k3:
binman: am625: add support for signing TIFSSTUB Images") did for TI AM62
SK board.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rework the flash.bin image generation such that it uses the new binman
nxp_imx8mimage etype. This way, the flash.bin is assembled in correct
order using plain binman, without any workarounds or sections assembled
in special DT node order.
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> # imx8mm_venice
Tested-by: Fabio Estevam <festevam@gmail.com> # imx8mm-evk and imx8mn-evk
Signed-off-by: Marek Vasut <marex@denx.de>
Include imx8mq-u-boot.dtsi in the board -u-boot.dtsi to pull in binman
configuration instead of duplicating it in the board -u-boot.dtsi again.
Drop the duplicate binman configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Enable PCIe/NVMe support on DH i.MX8M Plus DHCOM PDK3. Except for
the configuration options which are enabled, add slight adjustment
to board u-boot.dtsi, which is necessary as there is currently no
driver for the I2C PCIe clock generator. Since the generator is
strapped to be always on, it is possible to supplant the generator
functionality by fixed-clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Some variants of the ROCK Pi 4 series have an SPI flash chip populated
which can be booted from. This patch enables support in U-Boot for
building the image for the SPI flash, support for booting U-Boot from the
SPI flash chip and support in U-Boot for accessing the SPI flash using
`sf` commands.
Not all variants (e.g. ROCK Pi 4B, ROCK 4 Model C Plus, ROCK 4SE) come
populated with an SPI flash chip, but have the footprint on the board so
a user could solder their own to the board. With this patchset applied,
these board variants without an SPI flash chip still boot from MMC.
I have enabled support for both Winbond and XTX SPI flash devices since
different hardware variants have different devices populated:
- `rockpi4_v13_sch_20181112.pdf` contains a Winbond part `W25Q64FWZPIG`
- `rockpi4_v14_sch_20210114.pdf` contains an XTX part `XT25F32BWOIGT`
The ROCK Pi 4 I have is marked as "ROCK PI 4 v1.48" and contains an SPI
flash chip from XTX:
=> sf probe
SF: Detected xt25f32 with page size 256 Bytes, erase size 4 KiB, total 4 MiB
In the interest of supporting all board variants and not regressing
existing users who boot from MMC, I have enabled support for booting from
both SPI flash chip variants in the defconfig and left the environment
storage location as MMC to not break existing users who have the
environment stored on MMC.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
To prepare for ROCK Pi 4A SPI flash support, sync the DTS from Linux which
includes an SPI flash node.
Kernel tag: v6.6-rc1
Kernel commits:
- eddf73029770 ("arm64: dts: rockchip: Enable internal SPI flash for ROCK \
Pi 4A/B/C")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
The vop node should not be included in TPL/SPL control FDT, it should
only be included at U-Boot proper pre-reloc phase.
Change to use bootph-some-ram prop to fix this.
Fixes: 6794063d50 ("ARM: dts: rk3328: Enable VOP for bootph-all")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for USB OTG, RockUSB and UMS to the generic RK3588S/RK3588
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The default pinctrl for UART2 is using M1 iomux, however, all other
supported RK3588 boards in U-Boot use M0 iomux for UART2.
Change to use the M0 pinctrl for UART2 to match other supported boards.
Fixes: b54c3d0dd6 ("rockchip: board: Add minimal generic RK3588S/RK3588 board")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for USB OTG, RockUSB and UMS to the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for booting from SPI flash using the generic RK3566/RK3568
target.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing emmc_datastrobe and sdmmc0_det pinctrl to fix possible issue
reading from eMMC or SD-card. Also use correct node for mmc1 alias.
Fixes: 683f61a13f ("rockchip: board: Add minimal generic RK3566/RK3568 board")
Fixes: 363cbd5781 ("rockchip: rk3568-generic: Enable eMMC HS200 mode")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix CoolPi 4 Model B and CoolPi CM5 EVB .dtb-file entries in Makefile.
Fixes: 3e15dee38d ("board: rockchip: Add support for rk3588 based Cool Pi CM5 EVB")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the commit aca95282c1 ("Makefile: Use the fdtgrep -u flag")
bootph props is propagating to parent nodes.
Update bootph props to ensure eMMC, SD-card and SPI flash is available
in SPL and U-Boot proper pre-reloc phase also remove unneeded bootph
props that automatically is propagated to parent nodes.
Also adjust pinctrl nodes to only be included in boot phases where they
are needed and add any missing pinctrl node needed in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the commit aca95282c1 ("Makefile: Use the fdtgrep -u flag")
bootph props is propagating to parent nodes.
Update bootph props to ensure eMMC, SD-card and SPI flash is available
in SPL and U-Boot proper pre-reloc phase also remove unneeded bootph
props that automatically is propagated to parent nodes.
Also adjust pinctrl nodes to only be included in boot phases where they
are needed and add any missing pinctrl node needed in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sort nodes and props in RK356x/RK3588 u-boot.dtsi alphabetically, nodes
is sorted by reg addr then by alphabetical order.
This has no intended change beside sorting existing nodes and removing
a duplicated usbdpphy0_grf node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK35xx SoCs contain a crypto engine block that can generate random
numbers.
Enable rng node in soc u-boot.dtsi and enable Kconfig options to take
advantage of the random generator.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3308-rock-pi-s with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Also fix use of USB 2.0 otg port by removing improper use of phy-supply
and regulator-always-on props.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync device tree from linux v6.8 and rename the rockchip,rk3308-mac
compatible in gmac_rockchip driver to match upstream linux.
Also move rk3308-roc-cc gmac node to u-boot.dtsi to not break features
not enabled in upstream device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3308 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 16 2024 - 12:36:12 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Imply SPL_PINCTRL and SPL_DM_SEQ_ALIAS to apply correct pinconf before
trying to load FIT from a device.
Move u-boot,spl-boot-order to soc u-boot.dtsi and define both sdmmc and
emmc nodes as fallback.
Also fix boot from eMMC (SD NAND) on ROCK Pi S by using correct pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3308 SoC contain a crypto engine block that can generate random
numbers.
Add rng node to soc u-boot.dtsi and enable Kconfig options to take
advantage of the random generator.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs the RK3308 has cpu id programmed into OTP
memory. The rockchip_otp driver already support the RK3308 variant.
However, the device tree is missing a node to enable use of OTP.
Add the missing otp node to soc u-boot.dtsi, enable the rockchip_otp
driver and enable use of misc_init_r() to set ethaddr based on cpu id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the new device devicetree files in dts/upstream/ and delete the old
ones. Still keep the -u-boot.dtsi with all u-boot specifics around.
There is one catch and that is fsl-ls1028a-kontron-sl28-var3.dts which
is not available upstream (yet!). For now, the base dts is used for this
variant as this only differ in the compatible and the (human readable)
model name.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Schneider HMIBSC board dts has already been reviewed upstream on the
linux-arm-msm mailing list. So once it comes through the Linux kernel
release cycle into the U-Boot dts/upstream subtree, a switch to
OF_UPSTREAM can be made. For the time being maintain the U-Boot copy.
Link: https://lore.kernel.org/linux-kernel/20240403043416.3800259-4-sumit.garg@linaro.org/
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
These files are all identical (or older) than those in dts/upstream.
Drop them as we now use upstream DTS files with OF_UPSTREAM.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Remove the reference to the xo clock which is on the unsupported rpmhcc
clock controller. It isn't needed for MMC functionality.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Of all T30 transformers, only the TF700T has a FullHD DSI panel,
which is connected via tc358768 RGB to DSI bridge. Since the
bridge driver is available now, TF700T can have video support.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF700T
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
For lock and io-reset pins 0 is the default value, while 1 is disabled
and 2 is enabled. This should be corrected to avoid regressions.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TF600T is pretty picky in terms of LV pinmux configuration.
The wrong setup will cause issues with eMMC and video.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Unlike all other transformers, TF600T has an SPI flash to store
boot firmware and requires precise SPI pinmux configuration.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Paz00 can have multiple panels with different timings, but they
all share common feature - panel exposes EDID.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZiUXVA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLR5AJ9g6i7STLs6+13Oa1RF0OVucjRaHwCfUsdodreO
NWJ4C4sWE4l/KeEjbLY=
=IiTw
-----END PGP SIGNATURE-----
Merge tag 'video-20240421' of https://source.denx.de/u-boot/custodians/u-boot-video
CI: https://source.denx.de/u-boot/custodians/u-boot-video/-/pipelines/20466
- simple_panel: support timing parsing from EDID
- dw_hdmi: fix gcc-14 compiler warnings
- dw_hdmi: support vendor PHY for HDMI
- rockchip: add Rockchip INNO HDMI PHY driver
- rockchip: RK3328 HDMI and VOP support
- evb-rk3328: enable vidconsole support
- Tegra DC and DSI improvements and Tegra 114 support
- add LG LG070WX3 MIPI DSI panel driver
- add Samsung LTL106HL02 MIPI DSI panel driver
- add Toshiba TC358768 RGB to DSI bridge support
- add basic support for the Parade DP501 transmitter
- Tegra 3 panel and bridge driver improvements
- simplefb: modernise DT parsing
- fdt_simplefb: Enumerate framebuffer info from video handoff
- preserve framebuffer if SPL is passing video hand-off
- fdt_support: allow reserving FB region without simplefb
Diverge DC driver setup to better fit each of supported generations
of Tegra SOC.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Ion Agorria <ion@agorria.com> # HTC One X
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab T114
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Model: Firefly roc-rk3328-cc
DRAM: 1 GiB (effective 1022 MiB)
Video device 'vop@ff370000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'rockchip_rk3328_vop': -28
Some drivers failed to bind
initcall sequence 000000003ffcd5e8 failed at call 000000000021a5c4 (err=-28)
### ERROR ### Please RESET the board ###
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
