Some of the rgxx3 devices do not have a way to recover from a poor
flash of a bootloader to eMMC. Set the device to always attempt to boot
from sdmmc0 first which ensures that we can override the boot from
emmc if we have a card present with a valid fit signature. The
expectation is that this will protect from the very unlikely chance
we have a valid FIT signature on the eMMC but the U-Boot stage fails
for some other reason.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove leftover DTSI files after OF_UPSTREAM conversion.
Those are no longer used and no longer necessary, remove them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com>
Javier Martinez Canillas <javier@dowhile0.org> says:
Hello,
I noticed that the IGEPv2 board did not boot anymore with mainline U-Boot.
This was caused by a driver change to allocate its platform data before
relocation and U-Boot not having enough pre-relocation heap size for this.
This series fixes this issue and also makes the board support more modern,
by enabling DM for SPL and migrating the IGEP boards to use upstream DTBs.
Enable OF_UPSTREAM to use upstream DT and add a ti/omap/ prefix to the
DEFAULT_DEVICE_TREE config option.
That way, a DTS from the upstream dts/upstream/src/ directory is used
instead of the arch/$(ARCH)/dts/ directory. These in turn are removed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This change is heavily based on commit e0cc7df9fd ("omap3_beagle: Update
for DM SPL support"), that did the same update for the OMAP3 Beagle board.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Use CSR_UCCTLCOMMAND instead of CSR_MCCTLCOMMAND
to do cache flush operation in M-mode and S-mode.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Cache could be enabled in harts_early_init board-specific hook,
so remove cache enablement in start.S
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The address we load TFA and OPTEE is configurable by the
CONFIG_K3_{ATF,OPTEE)_LOAD_ADDR, but the DT node reservations remain
static which can cause some confusion about where exactly these firmware
are exactly. Fix this by updating the reserved-memory{} nodes when the
loaded address does not match the address in DT.
Reported-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
This iRAM APM area is needed for I3C access to PMIC via APM block.
Without this mapping any access to APM iRAM leads to "Synchronous Abort"
exception.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the nodes in e850-96 appended device tree that add bootph-all
flags are not necessary. All those nodes are instantiated as
dependencies of other nodes anyway. Remove those nodes to avoid
cluttering the appended dts. 'bdinfo' reports 768 bytes reduction for
"Early malloc usage", and 'dm tree' output doesn't change. Keep only
pmu_system_controller changes, which are actually needed for serial to
work properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use upstream device tree files and bindings. To do so:
- imply (enable) OF_UPSTREAM option for E850-96 target
- point DEFAULT_DEVICE_TREE in E850-96 config to upstream dts
- remove now not needed local dts files, binding docs and headers
- update MAINTAINERS and board/samsung/e850-96/MAINTAINERS
correspondingly
Upstream device tree files for Exynos850 SoC and E850-96 board are
pretty much the same as local (removed) ones, so the conversion is
rather straightforward and painless in this case. The appended dts file
(arch/arm/dts/exynos850-e850-96-u-boot.dtsi) stays unchanged.
The only remaining local dt-bindings doc for E850-96 board is
exynos-pmu.yaml. It wasn't removed as it's quite different from Linux
kernel version. Particularly U-Boot local version of exynos-pmu.yaml
describes "samsung,uart-debug-1" property, which is not present in Linux
kernel binding. Later it might be upstreamed to Linux kernel, and once
it's done the U-Boot exynos-pmu.yaml binding can be removed.
No functional change.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
See commit 008ba0d56d ("rockchip: Add common default bss and stack
addresses") for memory layout. This migrates PX30 to use the new layout,
except for TPL. Indeed, PX30 is extremely limited in SRAM, so we need to
be extra careful about what goes into the TPL and how much we can
allocate there, so let's keep the current value for
TPL_SYS_MALLOC_F_LEN (already present in the PX30-specific Kconfig, from
an earlier commit).
This will allow us to use the same memory layout on one more Rockchip
SoC, which is always a nice thing. Additionally, this will make it
easier to fix U-Boot proper pre-reloc running out of memory on PX30 in a
subsequent commit.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
This [pull request] for master fixes framebuffer video on almost all
Qualcomm platforms where the framebuffer is initialised by the first
stage bootloader.
* We already have a header 'backtrace', there is no need to repeat the
word backtrace on every line.
* Add a blank line before the backtrace section of the crash report for
improved readability.
* If U-Boot is compiled without backtrace, there is no need to write a
message at all.
* Avoid #ifdef. We prefer functions to always be compiled and let
the linker remove them if not needed.
* Foresee 3 digits for the backtrace index.
For testing the 'exception' command can be used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The EEPROM provides information about the size of the eMMC.
Provide a new function get_mmc_size_from_eeprom() to read it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
The newly introduced carve_out_reserved_memory causes issues when
U-Boot is chained from the lk2nd bootloader. lk2nd provides a
simple-framebuffer device and marks the framebuffer region as no-map in
the supplied /reserved-memory. Consequently, the simple_video driver
triggers a page fault when it tries to write to this region.
As per Caleb's advice, this simple patch only does the carveouts for the
qcs404 SoC for which it was originally designed. The intent is to do the
carveouts for more Qualcomm SoCs in future.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Roger Quadros <rogerq@kernel.org> says:
Sync AM62 device tree files with Linux v6.9 and
add in the missing bits in -u-boot.dtsi to get CPSW
Ethernet working.
CI testing: https://github.com/u-boot/u-boot/pull/534
Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
On all Raspberry Pi platforms, we're loaded by a prior stage firmware
that has assembled and passed on a device tree binary for us to use.
Switch to using this tree by default.
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: François Ozog <francois.ozog@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Remove DTs which are now replaced by OF_UPSTREAM counterparts.
No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com> #beacon boards
Let's provide get_boot_device() for AM64, similar to what we did
in commit 2f9095e2bf ("arm: mach-k3: am625: Provide a way to obtain boot
device for non SPLs") for AM62.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
J7200 has SR1.0 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-SE SR1.0 and HS-FS SR1.0 so
add support for them.
Reported-by: Suman Anna <s-anna@ti.com>
Reported-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
J721E has SR1.1 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-FS SR1.1 so add support for
them.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Greg Malysa <greg.malysa@timesys.com> says:
This series adds support for the ADI SC5xx machine type and includes two
core drivers that are required for being able to boot any board--a UART
driver, the gptimer driver which is used as a clock reference (CNTVCNT
is not supported on the armv7 sc5xx SoCs) and the clock tree driver. Our
corresponding Linux support relies on u-boot configuring the clocks
correctly before booting, so it is not possible to boot any board
without the CGU/CDU configuration happening here. There are also no
board files, device trees, or defconfigs included here, but some common
definitions that will be used to build board files currently are. The
sc5xx SoCs themselves include many armv7 families (sc57x, sc58x, and
sc594) all using an ARM Cortex-A5, and one armv8 family (sc598) indended
to be a drop-in replacement for the SC594 in terms of peripherals, with
a Cortex-A55 instead.
Some of the configuration code in dmcinit and clkinit is quite scary and
causes a lot of checkpatch violations. It is modified from code
initially provided by ADI, but it has not been fully rewritten. There's
a question of how important it is to clean up this code--it has some
quality violations, but it has been in use (including in production) for
over two years and is known to work for performing the low level SoC
initialization, while a rewrite might introduce timing or sequence bugs
that could take a significant amount of time to detect in the future.
Add support for the SC5xx machine type from Analog Devices. This
includes support for the SC57x, SC58x, SC59x, and SC59x-64 SoCs, which
have many common features such as common ADI IP blocks, and SHARC DSP
cores. This commit introduces core functionality required for all boards
using an SC5xx SoC, such as:
- SPL configuration
- Required CPU hooks such as reset
- Boot ROM interaction to load the stage 2 bootloader in the reference
configuration. Other options are possible but not officially supported
at this time
- SoC-common configuration expected to be reused by all boards
- Early initialization for system clocks and DDR controller
Co-developed-by: Greg Malysa <greg.malysa@timesys.com>
Signed-off-by: Greg Malysa <greg.malysa@timesys.com>
Co-developed-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Ian Roberts <ian.roberts@timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
The DM37 and OMAP35 SOM-LV share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
The DM37 and OMAP35 Torpedo share a few files, but both of them
can be migrated to OF_UPSTREAM with a small update to their
respective u-boot.dtsi files to address changes made the aliases.
Both defconfigs need to properly point to the upstream directory
structure for the device trees. With those updated, the U-Boot
device tree files can be deleted.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT from Makefile
With the feature of OF_UPSTREAM now available, the device trees
for the SOM and baseboard can now deleted and the device tree
locations need to point to the ti/omap directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove DT reference from Makefile.
The da850-evm can remove the U-Boot device trees if migrated
to OF_UPSTREAM. This means pointing the device trees to the
ti/davinci directory.
Signed-off-by: Adam Ford <aford173@gmail.com>
v2: Remove DTS from Makefile.
