Implement support for LED activity. If the feature is enabled,
make the defined ACTIVITY LED to signal traffic.
Also turn the ACTIVITY LED OFF if a CTRL-C is detected in the main
net loop function.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the lmb_read_check() function to verify if it is safe to use a
region of memory to load data from a tftp command. The current logic
checks the amount of free memory available, starting from the 'load
address'. This call fails if the same region of memory has been used
earlier. This used to work earlier as the LMB memory map had a local
scope and was not persistent. Fix this issue by using the
lmb_read_check() call instead which only returns an error in case the
memory region has been marked for not allowing re-use.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
With the changes to make the LMB reservations persistent, the common
memory regions are being added during board init. Remove the
now superfluous lmb_init_and_reserve() function.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With the introduction of separate config symbols for the SPL phase of
U-Boot, the condition checks need to be tweaked so that platforms that
enable the LMB module in SPL are also able to call the LMB API's. Use
the appropriate condition checks to achieve this.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current LMB API's for allocating and reserving memory use a
per-caller based memory view. Memory allocated by a caller can then be
overwritten by another caller. Make these allocations and reservations
persistent using the alloced list data structure.
Two alloced lists are declared -- one for the available(free) memory,
and one for the used memory. Once full, the list can then be extended
at runtime.
[sjg: Use a stack to store pointer of lmb struct when running lmb tests]
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
[sjg: Optimise the logic to add a region in lmb_add_region_flags()]
Option Acknowledgment (OACK) is an extension of TFTP protocol (see rfc2347).
Not all tftp servers implements it. For example it does not supported by
tftpd server from debian-11 (https://packages.debian.org/bullseye/tftpd).
Starting the "tftpput $loadaddr $size out_file" command with such server
will results in the following packets flow:
192.168.27.3 192.168.27.1 TFTP Write Request, ...
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 0
192.168.27.3 192.168.27.1 TFTP Write Request, ...
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 0
192.168.27.3 192.168.27.1 TFTP Write Request, ...
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 0
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 0
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 0
...
so, no data transfer happening.
Here is a packets flow for tftp-server with OACK support
(tftpd-hpa: https://packages.debian.org/stable/tftpd-hpa)
192.168.27.3 192.168.27.1 TFTP Write Request, ...
192.168.27.1 192.168.27.3 TFTP Option Acknowledgement, ...
192.168.27.3 192.168.27.1 TFTP Data Packet, Block: 1
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 1
192.168.27.3 192.168.27.1 TFTP Data Packet, Block: 2
192.168.27.1 192.168.27.3 TFTP Acknowledgement, Block: 2
and this time data transfer starts normally.
As we can see there is no OACK packet in the first case. Investigating
an issue we'll find out:
1) tftp_start() sets
tftp_state = STATE_SEND_WRQ;
2) on OACK tftp_handler() sets
tftp_state = STATE_DATA;
and send a first DATA packet.
3) on ACK tftp_handler() will call a tftp_send() function.
tftp_send() will
* tftpd with OACK support:
Current state is STATE_DATA, so transmittion of data packet will
happen.
* tftpd without OACK support
Current state is STATE_SEND_WRQ, so retransmission of WRQ packet
will happen. Thus tftpd-server will retransmit an ACK.
This will repeats until timeout happens.
According to RFC1350 this is wrong. We should start data transfer
instead of WRQ retransmission.
This patch fix an issue, so tftpput works fine with both types of servers.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now it is clear that the feature actually depends on efi interfaces,
not "bootefi" command. efi_set_bootdev() will automatically be nullified
if necessary efi component is disabled.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
One extra character was being checked in the IPv6 string which caused the
last character of the address to be neither '\0' nor ':'. This raises an
error condition and causes the function to always return an error. This
issue was resolved by this fix.
Signed-off-by: Ehsan Mohandesi <emohandesi@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
In rfc7440, if an ACK is not received by the server or if the
last data block in a window is dropped, the server will timeout and
retransmit the window. In this case, the block count received will be
less than the internal block count. In this case, the client
should not ACK. ACK should only be sent if the received block
count is greater than the expected block count.
Signed-off-by: Sean Edmond <seanedmond@linux.microsoft.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The command tftpboot uses IPv4 by default. Add the possibility to use IPv6
instead. If an address in the command is an IPv6 address it will use IPv6
to boot or if there is a suffix -ipv6 in the end of the command it also
force using IPv6. All other tftpboot features and parameters are left
the same.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-Boot does not support IP fragmentation on TX (and unless
CONFIG_IP_DEFRAG is set, neither on RX). So the blocks we send must
fit in a single ethernet packet.
Currently, if tftpblocksize is set to something like 5000 and I
tftpput a large enough file, U-Boot crashes because we overflow
net_tx_packet (which only has room for 1500 bytes plus change).
Similarly, if tftpblocksize is set to something larger than what we
can actually receive (e.g. 50000, with NET_MAXDEFRAG being 16384), any
tftp get just hangs because we never receive any packets.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Nothing inside this block depends on NET_TFTP_VARS to be set to parse
correctly. Switch to C if() in preparation for adding code before
this (to avoid a declaration-after-statement warning).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
[trini: Update to cover CONFIG_TFTP_PORT case as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
No platforms enable the functionality to tftp directly to NOR flash, and
this is discouraged by the documentation. Remove this code. Further,
this highlights an oddity of the code. Un-indent the start of this
function.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some globals where not properly initialized causing timeouts
as data packets where not immediately acknowledged.
Fixes: cc6b87ecaa ("net: tftp: Add client support for RFC 7440")
Signed-off-by: Arjan Minzinga Zijlstra <arjan.minzingazijlstra@fox-it.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
in tftpboot, if ack was already sent previously for this
packet, don't send again.
Fixes: cc6b87ecaa ("net: tftp: Add client support for RFC 7440")
Reported-by: Suneel Garapati <suneelglinux@gmail.com>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Suneel Garapati <suneelglinux@gmail.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When the tftp server did not send any OACK, the tftp_next_ack variable
was not set to the correct value . As the server was transmitting
blocks we generated a lot of 'Received unexpected block: $n, expected
$n+1' error messages. Depending on the timeout setting the transfer
could still complete though.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Ramon Fried <rfried.dev@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Up to now the bootefi command used the last file loaded to determine the
boot partition. This has led to errors when the fdt had been loaded from
another partition after the EFI binary.
Before setting the boot device from a loaded file check if it is a PE-COFF
image or a FIT image.
For a PE-COFF image remember address and size, boot device and path.
For a FIT image remember boot device and path.
If the PE-COFF image is overwritten by loading another file, forget it.
Do not allow to start an image via bootefi which is not the last loaded
PE-COFF image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When load the last block, the "len" might not be a block size. This cause
loading the incorrect last block data.
The fix change "len" to tftp_block_size and minus one tftp_block_size
for offset calculation.
Use same offset calculation formula as in store_block().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
tftp_cur_block start with 1 for first block, but tftp_cur_block counter is
start with zero when block number is rollover. The existing code
"tftp_cur_block - 1" will cause the block number become -1 in store_block()
when tftp_cur_block is 0 when tftp_cur_block is rollover.
The fix pass in tftp_cur_block to store_block() and minus the
tftp_block_size when do the offset calculation.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Fixes missing update to tftp_prev_block counter before increase
tftp_cur_block counter when do the tftpput operation.
tftp_prev_block counter is used in update_block_number() function to
check whether block number (sequence number) is rollover. This bug
cause the tftpput command fail to upload a large file when block
number is greater than 16-bit (0xFFFF).
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Add support for RFC 7440: "TFTP Windowsize Option".
This optional feature allows the client and server
to negotiate a window size of consecutive blocks to send as an
alternative for replacing the single-block lockstep schema.
windowsize can be defined statically during compilation by
setting CONFIG_TFTP_WINDOWSIZE, or defined in runtime by
setting an environment variable: "tftpwindowsize"
If not defined, the windowsize is set to 1, meaning that it
behaves as it was never defined.
Choosing the appropriate windowsize depends on the specific
network topology, underlying NIC.
You should test various windowsize scenarios and see which
best work for you.
Setting a windowsize too big can actually decreases performance.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
RFC2348, RFC2349:
- Option string is case in-sensitive.
- Client must generate ERR pkt in case option value mismatch in server OACK
- Fix debug print for options
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
During packet sequence number wraparound the show_block_marker() API was
not called, as a result the progress marker doesn't stay within column
boundary. Use position in file instead of sequence number to align the
marker.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Remove the unneeded define TFTP_MTU_BLOCKSIZE.
Since the KConfig migration done by commit b618b37076 ("net:
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig"), CONFIG_TFTP_BLOCKSIZE
is always defined and can be used directly to avoid confusion
(fallback to 1468 in code is never used).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
During testing of qemu-riscv32 with a 2GiB memory configuration,
tftp always fails with a error message:
Load address: 0x84000000
Loading: #
TFTP error: trying to overwrite reserved memory...
It turns out the result of 'tftp_load_addr + tftp_load_size' just
overflows (0x100000000) and the test logic in store_block() fails.
Fix this by adjusting the end address to ULONG_MAX when overflow
is detected.
Fixes: a156c47e39 ("tftp: prevent overwriting reserved memory")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a follow-up, change the name of the newly introduced function
'lmb_get_unreserved_size' to 'lmb_get_free_size', which is more
appropriate.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix test/lib/lmb.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes CVE-2018-18439 ("insufficient boundary checks in network
image boot") by using lmb to check for a valid range to store
received blocks.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Always build lib/lmb.o on LMB and lib/fdtdec.o on OF_LIBFDT]
Signed-off-by: Tom Rini <trini@konsulko.com>
The same basic parsing was implemented in tftp and nfs, so add a helper
function to do the work once.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
For strncpy() select a minimal string length of destination and source
strings, here DEFAULT_NAME_LEN is preferable to MAX_LEN.
Due to the NUL-terminated contents of default_string the change is
a noop, however it removes a compilation warning if SH2/3/4 platform
specific strncpy() function is used:
In file included from include/linux/string.h:21:0,
from include/common.h:28,
from net/tftp.c:9:
net/tftp.c: In function 'tftp_start':
arch/sh/include/asm/string.h:52:42: warning: array subscript is above array bounds [-Warray-bounds]
: "0" (__dest), "1" (__src), "r" (__src+__n)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
