for rk3308, all defconfigs have CONFIG_OF_LIBFDT_OVERLAY=y, so enable it
by default.
for rk3328, any defconfig doesn't have it. but there is no strong reason
not to enable it. at least it's required for ROCK Pi E.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All RK3308 boards has now been synced to Linux kernel v6.8 DTs and can
migrate to use OF_UPSTREAM.
Migrate all RK3308 boards to use OF_UPSTREAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3308-roc-cc with new defaults.
Add OF_LIBFDT_OVERLAY=y to support device tree overlays.
Remove the SPL_DRIVERS_MISC=y option, no misc driver is used in SPL.
Remove BOOTDELAY=0, SYS_CONSOLE_INFO_QUIET=y and enable more CMD to
allow use of U-Boot cmdline.
Add DM_ETH_PHY=y and PHY_REALTEK=y to support onboard ethernet PHY.
Add PHY_ROCKCHIP_INNO_USB2=y, DM_USB_GADGET=y and remove USB_DWC2=y to
allow full use of USB 2.0 host and otg ports.
Enable EFI_LOADER to allow EFI boot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When RK3308 boards run SPL from eMMC and fail to load FIT from eMMC due
to it being missing or checksum validation fails there can be a fallback
to read FIT from SD-card. However, without proper pinctrl configuration
reading FIT from SD-card may fail:
U-Boot SPL 2024.04-rc4 (Mar 16 2024 - 12:36:12 +0000)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
Card did not respond to voltage select! : -110
mmc_init: -95, time 12
spl: mmc init failed with error: -95
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices (err=-6)
### ERROR ### Please RESET the board ###
Fix this by tagging related emmc and sdmmc pinctrl nodes with bootph
props. Also sort and move common nodes shared by all boards to the SoC
u-boot.dtsi.
Imply SPL_PINCTRL and SPL_DM_SEQ_ALIAS to apply correct pinconf before
trying to load FIT from a device.
Move u-boot,spl-boot-order to soc u-boot.dtsi and define both sdmmc and
emmc nodes as fallback.
Also fix boot from eMMC (SD NAND) on ROCK Pi S by using correct pinctrl.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3308 SoC support ARMv8 Cryptography Extensions and use of the
ARMv8 crypto extensions help speed up FIT checksum validation in SPL.
Imply ARMV8_SET_SMPEN and ARMV8_CRYPTO to take advantage of the crypto
extensions for SHA256 when validating checksum of FIT images.
Imply SPL_FIT_SIGNATURE and LEGACY_IMAGE_FORMAT to enable FIT checksum
validation on all RK3308 boards.
Also disable CONFIG_SPL_RAW_IMAGE_SUPPORT in board defconfigs to ensure
SPL does not try to jump to code that failed checksum validation.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Without DOS_PARTITION support U-Boot is not able to boot an OS stored
into an SD card with MBR partitions table. This is still a quite common
case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip
RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are
the only RK boards missing of DOS_PARTITION.
Reported-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DEBUG_UART_SKIP_INIT feature is implemented only by s5p (DEBUG_UART_S5P)
and pl01x (DEBUG_UART_PL010 or DEBUG_UART_PL011) serial drivers, but all
ARCH_ROCKCHIP configs rely on default DEBUG_UART_NS16550. The ns16550
serial driver does not depends on DEBUG_UART_SKIP_INIT, so drop it from
rockchip configs.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The "cmd/Kconfig" has a TODO description for CMD_MISC that it should
really be named as CMD_SLEEP. Change it in the whole source tree.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
