This enables the 'rproc' command, allowing users to
start, stop, and manage co-processors as well as load firmware
images.
Useful for systems with auxiliary cores, such as M4 or R5 cores
in the AM64x soc.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Enable ENV_IS_IN_SPI_FLASH to read the environment from the SPI
flash when booting from it. The oftree, kernel and ramdisk sizes
are located in this environment and therefore required to boot
an initramfs.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable ENV_OVERWRITE to allow environment variables to be
overwritten within the board code. This is required to add
MAC addresses during SOM detection.
Additionally, set ENV_IS_NOWHERE for boot sources other than MMC.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable the GPIO command to allow access to the GPIO pins.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The phyBOARD-Electra does not include a PCA953x I2C GPIO multiplexer.
Remove this configuration as it is a remnant from another
defconfig, and enable CONFIG_DA8XX_GPIO for the DA8XX DaVinci GPIO
controller instead.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable raw & on disk capsule updates and provide configs required
for updating MTD devices. Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Include SoM dt-overlays for DT control so we can include them
into our u-boot FIT image.
While at it also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Daniel Schultz <d.schultz@phytec.de> says:
This patch stack extends the phyCORE-AM62x/AM64x U-Boot by following boot
sources:
- Load U-Boot with USB DFU
- Load a Linux and initramfs from OSPI/QSPI NOR flash
- Load a Linux and rootfs from Network
Moreover, it adds required changes to the environment to boot an A/B
system with RAUC and includes some minor fixes.
The phyCORE-AM64x board code sets an environment variable 'boot'
with the device U-Boot booted from. Use this variable in
CONFIG_BOOTCOMMAND to boot Linux from the same boot device by
default.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Enable CONFIG_OF_BOARD_SETUP to fixup kernel device tree with mtd
partitions.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more
direct way. This makes it easier to understand the options with
'make menuconfig'.
There are three different ways of specifying the offset:
- sector offset
- partition number
- partition type
So make these a choice, so it is more obvious what is going on.
Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the rtc command for testing this device. Additionally, add smc
and cache commands to boot non-Linux firmwares on the A53.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Enable mtd command and remove SPI NOR flashes we do not
populate on our SoMs.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
Update environment location to align with OSPI fixed-partition
definitions and provide a redundant environment at a 2nd location.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Daniel Schultz <d.schultz@phytec.de>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_BOARD_LATE_INIT to use PHYTECs common board_late_init()
to set handy environment variables for u-boot.
Also, resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
The phycore-am64x can be migrated to OF_UPSTREAM.
Drop redundant device tree files, update MAINTAINERS and
defconfig's DEFAULT_DEVICE_TREE for ti vendor prefix accordingly.
While at it, drop the redundant definitions of AM642_PHYBOARD_ELECTRA_DTB
& SPL_AM642_PHYBOARD_ELECTRA_DTB from the binman dtsi file.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
