GPIO reset and power-off functionality depends on device tree data, which
is often absent in SPL or TPL. To address this, incorporate PHASE_ into the
config option and add Kconfig option or each phase.
Adjust SYSRESET_GPIO and POWEROFF_GPIO uses to address possible
regressions.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
At present there is a hex value SPL_STACK which both determines whether
SPL has its own initial stack and the hex value of that stack.
Split off the former into SPL_HAVE_INIT_STACK with SPL_STACK depending
on that and only providing the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync defconfig files]
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.
Signed-off-by: Tom Rini <trini@konsulko.com>
DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is
selected without GPIO which ends up in compilation error:
undefined reference to `dm_gpio_set_value'
undefined reference to `dm_gpio_get_value'
undefined reference to `dm_gpio_free'
undefined reference to `gpio_request_by_name'
Signed-off-by: Michal Simek <michal.simek@amd.com>
[trini: Fix configs which had relied on these select's]
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop falcon mode configs from microblaze-generic_defconfig, so that a
defconfig build will still boot into u-boot proper.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Axi qspi controller supports 32-bit & 24-bit addressing modes
for micron, macronix & spansion flash parts. But for winbond
flashes it only supports 24-bit addressing mode.
Enable CONFIG_SPI_FLASH_BAR to use extended addressing mode
to make 32-bit addressing mode work on all flashes.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f3864966c8ddd766a1702ad61b0e008a1f57462f.1665565423.git.michal.simek@amd.com
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BOOTM_LEN
As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().
Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
Enable u-boot.elf recreation from u-boot.bin to prepare for removing manul
relocation. Enable option for big endian configuration but it is not used
too much that's why it is completely untested.
By supporting this system there is a need to define LITTLE/BIG endian
Kconfig options to pass -EL/-EB flags.
Full command line for u-boot.elf recreation looks like this:
microblazeel-xilinx-linux-gnu-objcopy -I binary -B microblaze \
-O elf32-microblazeel u-boot.bin u-boot-elf.o
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e242a519fcd1c693b9103c5599b515af555ca43.1655299267.git.michal.simek@amd.com
This converts the following to Kconfig:
CONFIG_SYS_SPL_ARGS_ADDR
In doing so, we also consistently use this variable for SPL_OS_BOOT and
not CONFIG_SYS_FDT_BASE in some cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FAULT_ECHO_LINK_DOWN
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Enable this feature by default to be able to work with env import/export
commands which are done in this slightly changed variable format (There is
addtional flag fields in variable file which is changing CRC calculation).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add distro boot support for microblaze and enable jtag, qspi,
dhcp, pxe boot targets for distro boot.
Enable DISTRO_DEFAULTS config in microblaze defconfig and also
enable support for spi xilinx driver & spi vendors to access
spi flash by distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
