mirror of
https://github.com/ARM-software/arm-trusted-firmware.git
synced 2025-04-19 19:14:28 +00:00
9bf31a59d1
TC3 and TC4 SCP makes use of the system timer interrupt as its own timer. Previously, this timer was marked as a G1S interrupt which routes the interrupt to the secure world and also enables it. This causes spurious interrupts once the SCP has unmasked the interrupt in the timer control itself. Note that we move the inclusion of the timer interrupt from CSS_G1S_INT_PROPS to CSS_G1S_IRQ_PROPS as the former is only used by TC. This will also result in removing the timer interrupt from TC2. This is not an issue as it does not make use of this interrupt in either the SCP or AP. Change-Id: I5cc88e2adffbc93fc3c9d9d41b5ba7235dbc39d9 Signed-off-by: Jackson Cooper-Driver <jackson.cooper-driver@arm.com> Signed-off-by: Leo Yan <leo.yan@arm.com>
209 lines
6.5 KiB
C
209 lines
6.5 KiB
C
/*
|
|
* Copyright (c) 2015-2024, Arm Limited and Contributors. All rights reserved.
|
|
*
|
|
* SPDX-License-Identifier: BSD-3-Clause
|
|
*/
|
|
|
|
#ifndef CSS_DEF_H
|
|
#define CSS_DEF_H
|
|
|
|
#include <common/interrupt_props.h>
|
|
#include <drivers/arm/gic_common.h>
|
|
#include <drivers/arm/tzc400.h>
|
|
|
|
/*************************************************************************
|
|
* Definitions common to all ARM Compute SubSystems (CSS)
|
|
*************************************************************************/
|
|
#define NSROM_BASE 0x1f000000
|
|
#define NSROM_SIZE 0x00001000
|
|
|
|
/* Following covers CSS Peripherals excluding NSROM and NSRAM */
|
|
#define CSS_DEVICE_BASE 0x20000000
|
|
#define CSS_DEVICE_SIZE 0x0e000000
|
|
|
|
/* System Security Control Registers */
|
|
#define SSC_REG_BASE 0x2a420000
|
|
#define SSC_GPRETN (SSC_REG_BASE + 0x030)
|
|
|
|
/* System ID Registers Unit */
|
|
#define SID_REG_BASE 0x2a4a0000
|
|
#define SID_SYSTEM_ID_OFFSET 0x40
|
|
#define SID_SYSTEM_CFG_OFFSET 0x70
|
|
#define SID_NODE_ID_OFFSET 0x60
|
|
#define SID_CHIP_ID_MASK 0xFF
|
|
#define SID_MULTI_CHIP_MODE_MASK 0x100
|
|
#define SID_MULTI_CHIP_MODE_SHIFT 8
|
|
|
|
/* The slave_bootsecure controls access to GPU, DMC and CS. */
|
|
#define CSS_NIC400_SLAVE_BOOTSECURE 8
|
|
|
|
/* Interrupt handling constants */
|
|
#define CSS_IRQ_MHU 69
|
|
#define CSS_IRQ_GPU_SMMU_0 71
|
|
#define CSS_IRQ_TZC 80
|
|
#define CSS_IRQ_TZ_WDOG 86
|
|
#define CSS_IRQ_SEC_SYS_TIMER 91
|
|
|
|
/* MHU register offsets */
|
|
#define MHU_CPU_INTR_S_SET_OFFSET 0x308
|
|
|
|
/*
|
|
* Define a list of Group 1 Secure interrupt properties as per GICv3
|
|
* terminology. On a GICv2 system or mode, the interrupts will be treated as
|
|
* Group 0 interrupts.
|
|
*/
|
|
#define CSS_G1S_INT_PROPS(grp) \
|
|
INTR_PROP_DESC(CSS_IRQ_MHU, GIC_HIGHEST_SEC_PRIORITY, grp, \
|
|
GIC_INTR_CFG_LEVEL), \
|
|
INTR_PROP_DESC(CSS_IRQ_GPU_SMMU_0, GIC_HIGHEST_SEC_PRIORITY, grp, \
|
|
GIC_INTR_CFG_LEVEL), \
|
|
INTR_PROP_DESC(CSS_IRQ_TZC, GIC_HIGHEST_SEC_PRIORITY, grp, \
|
|
GIC_INTR_CFG_LEVEL)
|
|
|
|
#define CSS_G1S_IRQ_PROPS(grp) \
|
|
CSS_G1S_INT_PROPS(grp), \
|
|
INTR_PROP_DESC(CSS_IRQ_SEC_SYS_TIMER, GIC_HIGHEST_SEC_PRIORITY, grp, \
|
|
GIC_INTR_CFG_LEVEL), \
|
|
INTR_PROP_DESC(CSS_IRQ_TZ_WDOG, GIC_HIGHEST_SEC_PRIORITY, grp, \
|
|
GIC_INTR_CFG_LEVEL)
|
|
|
|
#if CSS_USE_SCMI_SDS_DRIVER
|
|
/* Memory region for shared data storage */
|
|
#define PLAT_ARM_SDS_MEM_BASE ARM_SHARED_RAM_BASE
|
|
#define PLAT_ARM_SDS_MEM_SIZE_MAX 0xDC0 /* 3520 bytes */
|
|
/*
|
|
* The SCMI Channel is placed right after the SDS region
|
|
*/
|
|
#define CSS_SCMI_PAYLOAD_BASE (PLAT_ARM_SDS_MEM_BASE + PLAT_ARM_SDS_MEM_SIZE_MAX)
|
|
#define CSS_SCMI_PAYLOAD_SIZE_MAX 0x100 /* 2x128 bytes for bidirectional communication */
|
|
#define CSS_SCMI_MHU_DB_REG_OFF MHU_CPU_INTR_S_SET_OFFSET
|
|
|
|
/* Trusted mailbox base address common to all CSS */
|
|
/* If SDS is present, then mailbox is at top of SRAM */
|
|
#define PLAT_ARM_TRUSTED_MAILBOX_BASE (ARM_SHARED_RAM_BASE + ARM_SHARED_RAM_SIZE - 0x8)
|
|
|
|
/* Number of retries for SCP_RAM_READY flag */
|
|
#define CSS_SCP_READY_10US_RETRIES 1000000 /* Effective timeout of 10000 ms */
|
|
|
|
#else
|
|
/*
|
|
* SCP <=> AP boot configuration
|
|
*
|
|
* The SCP/AP boot configuration is a 32-bit word located at a known offset from
|
|
* the start of the Trusted SRAM.
|
|
*
|
|
* Note that the value stored at this address is only valid at boot time, before
|
|
* the SCP_BL2 image is transferred to SCP.
|
|
*/
|
|
#define SCP_BOOT_CFG_ADDR PLAT_CSS_SCP_COM_SHARED_MEM_BASE
|
|
|
|
/* Trusted mailbox base address common to all CSS */
|
|
/* If SDS is not present, then the mailbox is at the bottom of SRAM */
|
|
#define PLAT_ARM_TRUSTED_MAILBOX_BASE ARM_TRUSTED_SRAM_BASE
|
|
|
|
#endif /* CSS_USE_SCMI_SDS_DRIVER */
|
|
|
|
#define CSS_MAP_DEVICE MAP_REGION_FLAT( \
|
|
CSS_DEVICE_BASE, \
|
|
CSS_DEVICE_SIZE, \
|
|
MT_DEVICE | MT_RW | MT_SECURE)
|
|
|
|
#define CSS_MAP_NSRAM MAP_REGION_FLAT( \
|
|
NSRAM_BASE, \
|
|
NSRAM_SIZE, \
|
|
MT_DEVICE | MT_RW | MT_NS)
|
|
|
|
#if defined(IMAGE_BL2U)
|
|
#define CSS_MAP_SCP_BL2U MAP_REGION_FLAT( \
|
|
SCP_BL2U_BASE, \
|
|
SCP_BL2U_LIMIT \
|
|
- SCP_BL2U_BASE,\
|
|
MT_RW_DATA | MT_SECURE)
|
|
#endif
|
|
|
|
/* Platform ID address */
|
|
#define SSC_VERSION_OFFSET 0x040
|
|
|
|
#define SSC_VERSION_CONFIG_SHIFT 28
|
|
#define SSC_VERSION_MAJOR_REV_SHIFT 24
|
|
#define SSC_VERSION_MINOR_REV_SHIFT 20
|
|
#define SSC_VERSION_DESIGNER_ID_SHIFT 12
|
|
#define SSC_VERSION_PART_NUM_SHIFT 0x0
|
|
#define SSC_VERSION_CONFIG_MASK 0xf
|
|
#define SSC_VERSION_MAJOR_REV_MASK 0xf
|
|
#define SSC_VERSION_MINOR_REV_MASK 0xf
|
|
#define SSC_VERSION_DESIGNER_ID_MASK 0xff
|
|
#define SSC_VERSION_PART_NUM_MASK 0xfff
|
|
|
|
#define SID_SYSTEM_ID_PART_NUM_MASK 0xfff
|
|
|
|
/* SSC debug configuration registers */
|
|
#define SSC_DBGCFG_SET 0x14
|
|
#define SSC_DBGCFG_CLR 0x18
|
|
|
|
#define SPNIDEN_INT_CLR_SHIFT 4
|
|
#define SPNIDEN_SEL_SET_SHIFT 5
|
|
#define SPIDEN_INT_CLR_SHIFT 6
|
|
#define SPIDEN_SEL_SET_SHIFT 7
|
|
|
|
#ifndef __ASSEMBLER__
|
|
|
|
/* SSC_VERSION related accessors */
|
|
|
|
/* Returns the part number of the platform */
|
|
#define GET_SSC_VERSION_PART_NUM(val) \
|
|
(((val) >> SSC_VERSION_PART_NUM_SHIFT) & \
|
|
SSC_VERSION_PART_NUM_MASK)
|
|
|
|
/* Returns the configuration number of the platform */
|
|
#define GET_SSC_VERSION_CONFIG(val) \
|
|
(((val) >> SSC_VERSION_CONFIG_SHIFT) & \
|
|
SSC_VERSION_CONFIG_MASK)
|
|
|
|
#endif /* __ASSEMBLER__ */
|
|
|
|
/*************************************************************************
|
|
* Required platform porting definitions common to all
|
|
* ARM Compute SubSystems (CSS)
|
|
************************************************************************/
|
|
|
|
/*
|
|
* The loading of SCP images(SCP_BL2 or SCP_BL2U) is done if there
|
|
* respective base addresses are defined (i.e SCP_BL2_BASE, SCP_BL2U_BASE).
|
|
* Hence, `CSS_LOAD_SCP_IMAGES` needs to be set to 1 if BL2 needs to load
|
|
* an SCP_BL2/SCP_BL2U image.
|
|
*/
|
|
#if CSS_LOAD_SCP_IMAGES
|
|
|
|
#if ARM_BL31_IN_DRAM
|
|
#error "SCP_BL2 is not expected to be loaded by BL2 for ARM_BL31_IN_DRAM config"
|
|
#endif
|
|
|
|
/*
|
|
* Load address of SCP_BL2 in CSS platform ports
|
|
* SCP_BL2 is loaded to the same place as BL31 but it shouldn't overwrite BL1
|
|
* rw data or BL2. Once SCP_BL2 is transferred to the SCP, it is discarded and
|
|
* BL31 is loaded over the top.
|
|
*/
|
|
#define SCP_BL2_BASE (BL2_BASE - PLAT_CSS_MAX_SCP_BL2_SIZE)
|
|
#define SCP_BL2_LIMIT BL2_BASE
|
|
|
|
#define SCP_BL2U_BASE (BL2_BASE - PLAT_CSS_MAX_SCP_BL2U_SIZE)
|
|
#define SCP_BL2U_LIMIT BL2_BASE
|
|
#endif /* CSS_LOAD_SCP_IMAGES */
|
|
|
|
/* Load address of Non-Secure Image for CSS platform ports */
|
|
#define PLAT_ARM_NS_IMAGE_BASE U(0xE0000000)
|
|
|
|
/*
|
|
* Parsing of CPU and Cluster states, as returned by 'Get CSS Power State' SCP
|
|
* command
|
|
*/
|
|
#define CSS_CLUSTER_PWR_STATE_ON 0
|
|
#define CSS_CLUSTER_PWR_STATE_OFF 3
|
|
|
|
#define CSS_CPU_PWR_STATE_ON 1
|
|
#define CSS_CPU_PWR_STATE_OFF 0
|
|
#define CSS_CPU_PWR_STATE(state, n) (((state) >> (n)) & 1)
|
|
|
|
#endif /* CSS_DEF_H */
|