Changed reg_clr to use the base address + RPI3_GPIO_GPCLR,
this corrects the reg_clr address.
Signed-off-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Signed-off-by: Abhi Singh <abhi.singh@arm.com>
Change-Id: I9ca50905efd4c640f143783c5a00676b246a2e26
Add initial configuration parameters for Rasperry Pi 3's sdhost
controller, and then configure and use those parameters.
This change allows warm reboots of UEFI on Raspberry Pi 3B+ where
existing code often fails with "unknown error". See discussion at:
https://github.com/pftf/RPi3/issues/24
The basic idea is that some initial configuration parameters
(clock rate, bus width) aren't configured into the hardware before
commands start being sent. I suspect that the particular setting
that matters is the "slow card" bit, but the initial clock setting
also seemed wrong to me.
Change-Id: I526def340def143f23f3422f1fc14c12c937ca7f
Signed-off-by: Rob Newberry <robthedude@mac.com>
- Removing platform dependencies from libc modules.
- Replacing panicking with actual error handling.
- Debug macros are included indirectly from assert.h. Removing
"platform_def.h" from assert.h and adding "common/debug.h"
where the macros are used.
- Removing hack for fixing PLAT_LOG_LEVEL_ASSERT to 40.
Instead removing assert with expression, as this
does not provide additional information.
Signed-off-by: Claus Pedersen <claustbp@google.com>
Change-Id: Icc201ea7b63c1277e423c1cfd13fd6816c2bc568
There is really no reason to use and pass around a struct when its only
member is the (fixed) base address.
Remove the struct and just use the base address on its own inside the
GPIO driver. Then set the base address automatically.
This simplifies GPIO setup for users, which now don't need to deal with
zeroing a struct and setting the base address anymore.
Change-Id: I3060f7859e3f8ef9a24cc8fb38307b5da943f127
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To allow sharing the driver between the RPi3 and RPi4, move the random
number generator driver into the generic driver directory.
Change-Id: Iae94d7cb22c6bce3af9bff709d76d4caf87b14d1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To allow sharing the driver between the RPi3 and RPi4, move the mailbox
driver into the generic driver directory.
Change-Id: I463e49acf82b02bf004f3d56482b7791f3020bc0
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit improves the SDHost driver for RPi3 as following:
* Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
block reading.
* In some low probability that SEND_OP_COND might results CRC7
error. We can consider that the command runs correctly. We don't
need to retry this command so removing the code for retry.
* Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
* Increase the clock to 50Mhz in data mode to speed up the io.
* Change the pull resistors configuration to gain more stability.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
This commit adds SDHost driver for RaspberryPi3. SDHost driver uses the
GPIO driver to connect the SDCard and SDHost. By using this driver it is
able to read/write raw blocks on SDCard.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
This commit adds GPIO driver for RaspberryPi3. The GPIO driver for RPi3
also provides the way to do pinmux selections.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
