The A/B loader [1] meant to be used for convenient CI testing.
The tool is installed into the same location as SA0, where it
conveniently fits due to its size, and where it makes use of
non-volatile PMIC registers to alternate between loading and
starting A or B copy of the BL2. The PMIC registers are used
because CPU registers are lost across reset.
In case the B copy is loaded, it is loaded from 8 MiB offset
from start of HF. In case the B copy fails to boot, a simple
reset of the system will switch back to booting previously
known working A copy and allow recovery.
The A/B loader sets MFIS bit MFISBTSTSR_BOOT_PARTITION to
pass the information which A/B copy is currently booting on
to TFA, which then loads the follow up components from 0 MiB
or 8 MiB offset, depending on whether the A or B copy is being
booted.
The MFISBTSTSR_BOOT_PARTITION interferes with regular A/B
switching during boot from eMMC as the boot media, where
the BootROM also sets MFISBTSTSR_BOOT_PARTITION bit in case
the system boots from SECOND eMMC HW BOOT partition.
Since the A/B loader is meant as a development and CI tool,
isolate the A/B loader use to RPC HF only and furthermore
isolate it behind new RCAR_RPC_HYPERFLASH_ABLOADER option
which is disabled by default.
[1] https://github.com/marex/abloader
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Change-Id: I04ecd50fa1405b78e1ba3949d54029034d4f22d8
Fixed the check of the address range which the program is loaded to.
Use the addresses and sizes in the BL31 and BL32 certificates to check
that they are within the range of the target address and size
defined inside the TF-A.
It also uses the addresses and sizes in the BL33x certificates to check
that they are outside the protected area defined inside the TF-A.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Code clean up
Change-Id: Iade15431fc86587489fb0ca9106f6baaf7e926e2
Check if next NS image invades a previous loaded image.
Correct non secure image area to avoid loading a NS image to secure
Move GZ compressed payload at 32 * compressed payload size offset,
so it is loaded in non-secure area and can be decompressed into
non-secure area too. It is unlikely that the up to 2 MiB compressed
BL33 blob would decompress to payload larger than 64 MiB .
Signed-off-by: Tobias Rist <tobias.rist@joynext.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix for compressed BL33
Change-Id: I52fd556aab50687e4791e5dbc45d425f802c8757
Make sure the length of the payload is not longer than the
DRAM size in check_load_area(), and make sure the payload
end does not cross protected area start.
Signed-off-by: Tobias Rist <tobias.rist@joynext.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I4d687be577a138352be9f92e5b0b6f596ffffba9
- Modify load destination variable of the Cert Header to static.
- Modify the return value to error (IO_FAIL) when failed to check
the Cert Header.
Signed-off-by: Koichi Yamaguchi <koichi.yamaguchi.zb@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Ief09a841ec8d2ae236de82d04855e6a47cfb43f0
In case MFISBTSTSR bit 4 is 1, that means the loader was started as
B-side. Load the remaining boot components from 8 MiB offset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I11d882f30ca4f0cf55fd28d3470ff1063d350d10
Move io driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic661e415c91a1fbfd5eee3bba86466037e51574b
2021-01-13 13:03:48 +00:00
Renamed from drivers/renesas/rcar/io/io_rcar.c (Browse further)
