This change introduces a few helper variables for dealing with verbose
and silent build modes: `silent`, `verbose`, `q` and `s`.
The `silent` and `verbose` variables are boolean values determining
whether the build system has been configured to run silently or
verbosely respectively (i.e. with `--silent` or `V=1`).
These two modes cannot be used together - if `silent` is truthy then
`verbose` is always falsy. As such:
make --silent V=1
... results in a silent build.
In addition to these boolean variables, we also introduce two new
variables - `s` and `q` - for use in rule recipes to conditionally
suppress the output of commands.
When building silently, `s` expands to a value which disables the
command that follows, and `q` expands to a value which supppresses
echoing of the command:
$(s)echo 'This command is neither echoed nor executed'
$(q)echo 'This command is executed but not echoed'
When building verbosely, `s` expands to a value which disables the
command that follows, and `q` expands to nothing:
$(s)echo 'This command is neither echoed nor executed'
$(q)echo 'This command is executed and echoed'
In all other cases, both `s` and `q` expand to a value which suppresses
echoing of the command that follows:
$(s)echo 'This command is executed but not echoed'
$(q)echo 'This command is executed but not echoed'
The `s` variable is predominantly useful for `echo` commands, where you
always want to suppress echoing of the command itself, whilst `q` is
more useful for all other commands.
Change-Id: I8d8ff6ed714d3cb401946c52955887ed7dca602b
Signed-off-by: Chris Kay <chris.kay@arm.com>
Coverity Issue 21268351
Fixed unused value of xspi read while reading training values from
xspi during warm reset.
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I779587afedb1c73d174a132bbfbcb21bf45bdff8
TF-A wants to eventually enable -Wold-style-definition globally. Convert
the rare few instances where this is still the case.
Signed-off-by: Boyan Karatotev <boyan.karatotev@arm.com>
Change-Id: I9c450fc875cf097e6de2ed577ea3b085821c9f5e
Fixed coverity issue for "shifting by a negtive value", returned
before go to the next shifting code.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I00171b057b8948cb9e9ec5d9405b2e32aba568fb
Coverity Issue detail:
underrun-local: Underrunning array bin[i].cl[k].caslat
at element index -1 (byte offset -1)
using index j (which evaluates to -1).
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I1ec4833bbd5db1ac51436eac606484eefc4338ee
Timing CFG 0 and Timing CFG 4 are ddr controller registers that
have been affected by 1d phy training during cold boot. They are
needed to be stored and restored along with phy training values.
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I29c55256e74456515aaeb098e2e0e3475697a466
we need to apply the value of CDD write to write for the write to
read CDD delay calculations. Since the current implementation always
provide a negative value of CDDwr so a value of zero was selected.
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I6829997d2ea6ba6cddaaab8332b82b8c66752d7e
Firmware buffer has already been mapped when loading 1D firmware,
so the same buffer address will be re-mapped when loading 2D
firmware. Move the buffer mapping to be out of load_fw().
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Idb29d504bc482a1e7ca58bc51bec09ffe6068324
Set the receiver gain to max value to recover
cold temp marginality issue for phy-gen2
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: If639fa3ed404cf6e1b8abcc2b7137db1fdd0b2c2
New UDIMM 18ADF2G72AZ-2G6E1 has raw card ID = 0x1F
Also, changing mask for raw card ID from - 0x8f -> 0x9f
Changing the mask need the raw card to changed from 0x0f -> 0x1f
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Iee8e732ebc5e09cdca6917be608f1597c7edd9f9
Corrects mapping of HNFs nodes with SNFs nodes based on their
proximity in CCN508 ring when disabling unused ddr controller.
When DDRC 2 disabled and DDR 1 is active the mapping is 0x3/3/8/8/8/8/3/3.
When DDRC 1 is disabled and DDR2 is active the mapping is 0x
18/18/13/13/13/13/18/18 .
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Signed-off-by: JaiPrakash Singh <JaiPrakash.singh@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I6ec1e02f8ad7e8bb8628913625ff5313a054dcc6
Use long instead of long long on aarch64 for 64_t stdint types.
Introduce inttypes.h to properly support printf format specifiers for
fixed width types for such change.
Change-Id: I0bca594687a996fde0a9702d7a383055b99f10a1
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
1. Refined struct soc_info_t definition.
2. Refined get_soc_info function.
3. Fixed some SVR persernality value.
4. Refined API to get cluster numbers and cores per cluster.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I3c20611a523516cc63330dce4c925e6cda1e93c4
NXP drivers header files are moved:
- from: drivers/nxp/<xx>/*.h
- to : include/drivers/nxp/<xx>/*.h
To accommodate these changes each drivers makefiles
drivers/nxp/<xx>/xx.mk, are updated.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I3979c509724d87e3d631a03dbafda1ee5ef07d21
DDR driver for NXP layerscape SoC(s):
- lx2160aqds
- lx2162aqds
- lx2160ardb
- Other Board with SoC(s) like ls1046a, ls1043a etc;
-- These other boards are not verified yet.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ic84a63cb30eba054f432d479862cd4d1097cbbaf
